Related Manuals for Sony PVS-R102
Summary of Contents for Sony PVS-R102
- Page 1 2-347-513-22 (1) Matrix Switcher Operating Instructions Before operating the unit, please read this manual thoroughly and retain if for future reference. PVS-R102 2002 Sony Corporation...
- Page 2 • Increase the separation between the Refer to them whenever you call upon maintenance (servicing) equipment and receiver. your Sony dealer regarding this product. instructions in the literature • Connect the equipment into an outlet accompanying the appliance. on a circuit different from that to Model No.
-
Page 3: Table Of Contents
Table of Contents Features Provided with the universal switching system that can Features ................3 afford to three types of the video signal. Location and function of parts ........... 4 4 composite video inputs, 2 component video inputs, and 4 Front panel ................ -
Page 4: Location And Function Of Parts
Location and function of parts Front panel MATRIX SWITCHER PVS-R102 INPUT POWER VIDEO COMPONENT/VIDEO LOCK OUTPUT 1 OUTPUT 2 /MONITOR INPUT 10 AUDIO 0dBu 0dBu 0dBu 0dBu 0dBu 0dBu 0dBu 0dBu 0dBu 0dBu AUDIO INPUT LEVEL -10dBu -10dBu -10dBu -10dBu... -
Page 5: Rear Panel
OUTPUT 1 crosspoint. several equipment such as a projector (component When Sony's projector is connected, connect OUT- signal) and monitor (composite signal). PUT 1 with INPUT A terminal of the projector, and plasma display is connected;... - Page 6 Location and function of parts 6 OUTPUT 2/MONITOR terminals (Video) • PROJECTOR position In this case, the same output signal is coming as These are RGB/Y R-Y B-Y output and VIDEO output same as OUTPUT 1. terminals. Select this side when connecting a multi-scan It outputs video signal of the INPUT channel which display to which 15k component signals can be was selected at the crosspoint of OUTPUT 2.
-
Page 7: How To Control Display
No control RS-232C terminal Connect the CONTROL 1 terminal with the OUTPUT 1 For the connection of a Sony projector and plasma display, output, and CONTROL 2/REMOTE terminal with the connect them as following diagram. OUTPUT 2 output of the projector or plasma display. -
Page 8: System Configuration
System Configuration System configuration using two projectors... -
Page 9: System Configuration Using A Projector And Monitors
System configuration using a Projector and Monitors... -
Page 10: Projector
System configuration System configuration using other manufacuture’s projector... -
Page 11: How To Control This Unit From External Controller
Pin No. Function Pin No. Functioncrosspoint 1 - 1 tally1 - 1 PVS-R102 crosspoint 1 - 2 tally1 - 2 crosspoint 1 - 3 tally1 - 3 crosspoint 1 - 4 tally1 - 4 Input terminals... -
Page 12: Block Diagram
Block Diagram VIDEO INPUT INPUT1 INPUT2 3D Comb INPUT3 filter NTSC / PAL Video (For NTSC) Color INPUT4 Switch 2D Comb Decorder filter OUTPUT1 (For PAL) Y R-Y B-Y R / R-Y G / Y B / B-Y Component RGB HD VD COMPONENT/VIDEO INPUT Video Y R-Y B-Y... -
Page 13: Dimensions
Dimensions 132(5 1/4) 482(19) POWER 336(13 1/4) Unit : mm (inches) *This drawing includes the supplied 430(17) feet. Specifications Color system NTSC, PAL AUDIO Reference level -10 dBu (Phono) VIDEO +4 dBu (XLR) Input terminal Frequency response 10 Hz – 100 kHz +0.5/-1.0 dB, 1 Vp-p (75 Ω... -
Page 14: Troubleshooting
Troubleshooting Before contacting a Sony Sales office or Dealer, check the following again. If the trouble persists, contact your local Sony Sales office or Dealer. Symptom Couses Remedy Connect the power cable securely in the AC Inlet and the wall Power cannot be turned ON.