Bosch Rexroth IndraDrive Troubleshooting Manual page 425
Hide thumbs
Also See for Rexroth IndraDrive:
- Applications manual (100 pages) ,
- Project planning manual (128 pages) ,
- Instruction manual (26 pages)
Table of Contents
13-8
Index
Rexroth IndraDrive
Not homed 8-28
Not ready for power on 8-45
O
Operating mode configuration (->S-0-0022) not allowed 9-60
operating states 5-1
Optional encoder not available 9-117
Optional encoder unknown 9-33
Oscillations of input signal outside tolerance range 9-106
Overcurrent external braking resistor 7-28
Overcurrent in power section 7-15, 8-2
Overflow of target position preset memory 7-98
Overvoltage in power section 8-1
P
P0 5-2
P1 5-2
P2 5-2
P3 5-2
Parameter calculation error (->S-0-0022) 9-50
Parameter conversion error (->S-0-0021) 9-18
Parameter default value incorrect (-> S-0-0021) 9-76, 9-79
Parameter limit error (->S-0-0022) 9-50
Parameters not copyable 9-75
Phase switching without ready signal 7-53
Phase synchr. lagless, encoder 1, real master axis 6-21
Phase synchr. lagless, encoder 1, virtual master axis 6-20
Phase synchr. lagless, encoder 2, real master axis 6-21
Phase synchr. lagless, encoder 2, virtual master axis 6-20
Phase synchronization, encoder 1, real master axis 6-19
Phase synchronization, encoder 1, virtual master axis 6-18
Phase synchronization, encoder 2, real master axis 6-19
Phase synchronization, encoder 2, virtual master axis 6-18
PL 5-2
PL Load parameter default values 7-79
Plausibility error actual position value 7-38
Plausibility error during commutation fine adjust 7-88
Plausibility error of actual position values 7-60, 8-15
Plausibility error of safety parameters 7-67, 8-16
Plausibility error of safety related operating mode 8-17
Plausibility error of selection 7-67
Plausibility error parameterized - effective threshold 7-37
Plausibility error safety related operating mode 7-39
PLC - Error nr. 1 7-80
PLC - Error nr. 2 7-81
PLC - Error nr. 3 7-81
PLC - Error nr. 4 7-82
PLC - Warning no. 1 8-19
PLC - Warning no. 2 8-19
PLC - Warning no. 3 8-19
PLC - Warning no. 4 8-20
PLC ? 4-2
PLC watchdog 7-55
Pos. window for safety rel. operational stop exceeded 7-35
Position control lagless, encoder 2 6-14
Position control lagless, encoder 2 drive controlled 6-31
Position mode lagless, encoder 1 6-14
Position mode lagless, encoder 1 drive controlled 6-31
Position mode with encoder 1 6-13
Position mode with encoder 1 drive controlled 6-30
Position mode with encoder 2 6-13
Position mode with encoder 2 drive controlled 6-30
Position of data record in MDT (S-0-0009) even 9-22
Position spindle command 9-6
Positioning block mode lagless, encoder 1 6-32
Positioning block mode lagless, encoder 2 6-33
Positioning block mode, encoder 1 6-32
Positioning block mode, encoder 2 6-33
DOK-INDRV*-GEN-**VRS**-WA01-EN-P
LSA Control S.L. www.lsa-control.com [email protected] (+34) 960 62 43 01
- Quick Links:
- Coded Diagnostic Drive Messages
- Error
Hide quick links:
Table of Contents
