Hide thumbs Also See for SIMATIC HMI IFP V2:

Quick Links

Gerät einbauen
1
Mounting the device
Vor Einbau und Inbetriebnahme – Before mounting and commissioning
1.1
WICHTIG: Beachten Sie alle dem Gerät beiliegenden
Dokumente und die Betriebsanleitung, bevor Sie das
Gerät einbauen und anschließen. Die vollständige
Dokumentation des Geräts finden Sie auf der beiliegen-
den DVD "Documentation and Drivers" und im Internet
(https://www.siemens.de/simatic-ipc-doku-portal).
IMPORTANT: observe all documents enclosed with the
device and the operating instructions manual before
mounting and connecting the device. You find the
complete documentation of the device on the enclosed
"Documentation and Drivers" DVD and on the internet
(https://www.siemens.com/simatic-ipc-doku-portal).
Das Handbuchsymbol weist auf detaillierte Informationen in der Betriebsanleitung hin.
The manual symbol refers to detailed information in the operating instructions.
Zulässige Einbaulagen – Valid Mounting positions
1.2
Montage an der Rückseite
Mounting at the rear side
1.3 Einbau vorbereiten – Preparing for mounting
Montageschiene befestigen
Fixing the mounting rail
2
PZ2
0,8 Nm
1
1.4 Gerät montieren – Mounting the device
Hutschienenmontage
Mounting on a standard rail
1
Informationen zu weiteren Montagevarianten / Information on additional mounting variants
Wandmontage / Wall mounting
Befestigen Sie die Transceiver Unit mit zwei Schrauben M4 über die beiden Langlöcher der
Montageschiene.
Fix the Transceiver Unit with two screws M4 via the two oblong holes of the mounting rail.
Material
Bohrungsdurchmesser Befestigungselement
Entsprechend der
Beton
Vorgabe des verwendeten
Befestigungselements
Gipskarton, mind. 13 mm dick
wählen
Metall, mind. 2 mm dick
Material
Bore diameter
Select according to the
Concrete
specification of the
mounting elements used
Plasterboard, min. 13 mm thick
Metal, min. 2 mm thick
50 °C
0 °C
Montage an einer Seite
Mounting at one side
Erforderlicher Frairäume
Required clearances
3
2
Dübel, ∅ 6 mm, 40 mm lang
Schraube, ∅ 4 mm, 40 mm lang
Kippdübel, ∅ 12 mm, 50 mm lang
Schraube M4 x 15
Mutter M4
Fixing element
Anchor, ∅ 6 mm, 40 mm long
Screw, ∅ 4 mm, 40 mm long
Toggle plug, ∅ 12 mm, 50 mm long
Screw M4 x 15
M4 nut
Gerät anschließen
2
Connecting the device
2.1 Potenzialausgleich – Equipotential bonding
1 1
6 mm
2
3
2.2 Stromversorgung anschließen – Connecting the power supply
Verwenden Sie für die DC 24 V-Versorgung nur Netzgeräte mit sicherer elektrischer Trennung nach
IEC 61010-2-201 oder IEC 60950-1 gemäß dem Standard SELV/PELV.
Die Versorgungsspannung darf nur innerhalb des angegebenen Spannungsbereichs liegen.
mm
Use only power supply units with safety isolation complying with IEC 61010-2-201 or IEC 60950-1
according to the SELV/PELV standard, for the 24 V DC supply.
The supply voltage must be within the specified voltage range.
1
6 mm
2
3
mitgelieferten
Ferrit wie
abgebildet
montieren.
6
Mount enclosed
ferrite as shown.
2.3 Leitungen sichern – Securing the cables
1
4
TX 20
M4
4 mm
5
I F P
I F P
1
1 5
5 0
5 0
0 0
0
0
0
0
V 2
V
V
V 2
V
5
4
Den
max. 200 mm
2
3
²
²
16 mm
7
0/OFF
M
8
L +
Sichern Sie die angeschlossenen
Leitungen zur Zugentlastung mit
Kabelbindern an den markierten
Befestigungselementen.
Achten Sie darauf, dass die
Leitungen durch die Kabelbinder
nicht gequetscht werden.
Use cable ties to secure the
connected cables to the selected
fixing elements for strain relief.
Make sure that the cables are not
crushed by the cable tie.
For use in Canada:
Arrêtez les câbles raccordés
pour une décharge de traction
avec les attache-câbles sur les
éléments de fixation marqués.
Veillez à ce que les câbles ne
soient pas écrasés par les
serre-câbles.
loading

Summary of Contents for Siemens SIMATIC HMI IFP V2

  • Page 1 Dokumente und die Betriebsanleitung, bevor Sie das Gerät einbauen und anschließen. Die vollständige Dokumentation des Geräts finden Sie auf der beiliegen- den DVD "Documentation and Drivers" und im Internet (https://www.siemens.de/simatic-ipc-doku-portal). 6 mm IMPORTANT: observe all documents enclosed with the device and the operating instructions manual before mounting and connecting the device.
  • Page 2 Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. Siemens AG Digital Industries Postfach 48 48 90026 NÜRNBERG DEUTSCHLAND Kopieren Sie die DVD “Documentation and Drivers“...

This manual is also suitable for:

Simatic hmi ifp v2 pro