Cisco 1100 Series Manual

Cisco 1100 Series Manual

Install and upgrade internal modules and field replaceable units
Hide thumbs Also See for 1100 Series:

Quick Links

Install and Upgrade Internal Modules and Field
Replaceable Units
The Cisco 1100 Series Integrated Services Routers have internal modules and field-replaceable units (FRUs)
that can be quickly and easily removed and replaced without having to send the entire router for repair.
This section describes how to install and upgrade the internal modules and FRUs in the Cisco 1100 Series
ISRs. The information is contained in the following sections:
Access Internal Modules
To access the internal modules on the router, you must first disconnect the power source and then remove the
chassis cover. See the Replacing the Chassis Cover section for instructions on how to remove and later
replace the chassis cover on the routers.
Warning
Only trained and qualified personnel should be allowed to install, replace or service this equipment. Statement
1030.
Warning
Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network
voltages. Statement 1041.
Warning
Power off the unit before you begin. Statement 237.
Access Internal Modules, on page 1
Locate Internal and External Slots for Modules, on page 3
Install an LTE Pluggable Module, on page 3
Install and Remove Small Form Pluggable Modules, on page 10
Install and Upgrade Internal Modules and Field Replaceable Units
1
loading

Summary of Contents for Cisco 1100 Series

  • Page 1 This section describes how to install and upgrade the internal modules and FRUs in the Cisco 1100 Series ISRs. The information is contained in the following sections: •...
  • Page 2 Replace the Chassis Cover The Cisco 1100 Series ISRs have a removable cover. Do not attempt to run the router without the cover. This can cause the router to overheat very quickly. To remove the chassis cover, use a number-2 Phillips screwdriver...
  • Page 3: Replace The Cover

    Install and Upgrade Internal Modules and Field Replaceable Units Replace the Cover Replace the Cover Warning The covers are an integral part of the safety design of the product. Do not operate the unit without the covers installed. Statement 1077 To replace the cover, perform the these steps: Step 1 Disconnect the power supply before you begin replacing the chassis cover.
  • Page 4 Install and Upgrade Internal Modules and Field Replaceable Units Install a Micro-SIM Card onto a USB LTE Dongle Figure 1: Micro-SIM Card Slot with Dust Cover Step 1 To insert a micro-SIM card into a USB LTE dongle, do these steps: a.
  • Page 5 Install and Upgrade Internal Modules and Field Replaceable Units Install a Micro-SIM Card onto a USB LTE Dongle Figure 2: LTE USB 2.0 Dongle for C1101-4P Number Description Supporting ring Magnet Extend outward 30mm Plug-in direction Number Description Supporting ring Dongle holder with magnet Router-C1101-4PLTEPW Install and Upgrade Internal Modules and Field Replaceable Units...
  • Page 6 Install and Upgrade Internal Modules and Field Replaceable Units Install an LTE Pluggable Module on a C1101-4P Follow the same procedure to install the USB LTE dongle onto routers with a vertical USB slot. Install an LTE Pluggable Module on a C1101-4P To insert the LTE pluggable module into the router, do these steps: Step 1 Insert and then gently push the LTE pluggable into the pluggable slot of C1101-4P until firmly fixed.
  • Page 7 Install and Upgrade Internal Modules and Field Replaceable Units Install an LTE Pluggable Module on a C1101-4P Figure 4: LTE Pluggable - C1127X-8PLTEP Item Description GPS Antenna LTE Antenna Ground Lug Kensingston Lock Slot Install and Upgrade Internal Modules and Field Replaceable Units...
  • Page 8 Install and Upgrade Internal Modules and Field Replaceable Units Install an LTE Pluggable Module on a C1101-4P Figure 5: LTE Pluggable - C1118-8PLTEP Item Description Mini-PCIE Common heat spreader + thermal interface Enclosure base to support 4-antenna 4-1 SMA-MHF4 cable assembly SMA Diversity Antenna for usability and Micro-USB port access Figure 6: LTE Pluggable - C1118-8PLTEP Back Panel Install and Upgrade Internal Modules and Field Replaceable Units...
  • Page 9 Install and Upgrade Internal Modules and Field Replaceable Units Install an LTE Pluggable Module on a C1101-4P Figure 7: C1118-8PLTEP with Micro SIM Slots This section describes how to insert a Micro-SIM card into an LTE pluggable module. To insert the Micro-SIM cards into an LTE Pluggable module: 1.
  • Page 10 Micro-SIM 0 (Away from the device) Install and Remove Small Form Pluggable Modules This section describes how to install and remove Small Form Pluggable (SFP) modules in the Cisco 1100 Series ISRs. The information is contained in the following sections:...
  • Page 11 Install and Upgrade Internal Modules and Field Replaceable Units Remove Small Factor Pluggable Module Step 1 Disconnect the power supply before you remove any module. Step 2 Disconnect all cables from the SFP. Step 3 Disconnect the SFP latch. Note SFP modules use various latch designs to secure the module in the SFP port.
  • Page 12 Install and Upgrade Internal Modules and Field Replaceable Units Remove Small Factor Pluggable Module Install and Upgrade Internal Modules and Field Replaceable Units...

This manual is also suitable for:

C1101-4p