Tests the integrity of a flow metering system by altering a number of flow measurement
parameters and measuring the values returned from the flow measuring system. (52 pages)
Page 2
Other than under explicit contractual com- mitments, in no event shall ABB be responsible or liable for any loss or damage resulting from the use of this manual or the application of the equipment. In case of discrepancies between the English and any other language version, the wording of the English version shall prevail.
Dangerous voltages can occur on the connectors, even though the auxiliary voltage has been disconnected. Non-observance can result in death, personal injury or substantial property damage. Only trained and qualified persons are allowed to connect and operate BIO-Tester Relion REX640. National and local electrical safety regulations must always be followed.
Page 4
4 B I O -T E S T E R R E X 6 4 0 Q U I C K O P E R AT I O N G U I D E 1. BIO-Tester overview Figure 1: BIO-Tester Relion® REX640 in a waterproof case and required cables Figure 2: Front view of BIO-Tester Relion®...
Page 5
B I O -T E S T E R R E X 6 4 0 Q U I C K O P E R AT I O N G U I D E 2. Preparations Refer to the local safety rules and regulations before starting any operations with BIO-Tester Relion® REX640. The auxiliary supply voltages of both the REX640 protection relay and the LHMI need to be switched off before the preparations.
Page 6
6 B I O -T E S T E R R E X 6 4 0 Q U I C K O P E R AT I O N G U I D E Connect the separate earth protection lead of BIO-Tester to the protective earth pin of the protection relay.
Page 7
B I O -T E S T E R R E X 6 4 0 Q U I C K O P E R AT I O N G U I D E Connect the correct connector cables between the BIO-Tester and the protection relay.
Page 8
8 B I O -T E S T E R R E X 6 4 0 Q U I C K O P E R AT I O N G U I D E Loosen the protective earth screw T20 on the LHMI but DO NOT remove the existing LHMI's earth lead.
Page 9
B I O -T E S T E R R E X 6 4 0 Q U I C K O P E R AT I O N G U I D E Push the cable connector in place and secure it by turning it clockwise.
Page 10
10 B I O -T E S T E R R E X 6 4 0 Q U I C K O P E R AT I O N G U I D E 3. Using BIO-Tester Relion® REX640 See the BIO-Tester Relion® REX640 User Manual for more information on using BIO-Tester. Select IED test mode.
Page 11
B I O -T E S T E R R E X 6 4 0 Q U I C K O P E R AT I O N G U I D E BIO1001/1003 BIO1002/1004 Push the BI button of each BIO module on BIO-Tester. SPO1 SPO2 SPO3...
Page 12
12 B I O -T E S T E R R E X 6 4 0 Q U I C K O P E R AT I O N G U I D E After successful testing: • Switch off the power supply. Ensure the de-energized state of both REX640 protection relay under testing and the BIO-Tester.
With regard to purchase orders, the agreed par- ticulars shall prevail. ABB OY does not ac- cept any responsibility whatsoever for po- tential errors or possible lack of information in this document.
Page 14
14 B I O -T E S T E R R E X 6 4 0 Q U I C K O P E R AT I O N G U I D E This page is intentionally left blank...
Page 15
B I O -T E S T E R R E X 6 4 0 Q U I C K O P E R AT I O N G U I D E This page is intentionally left blank...