Table of Contents
Assembly Instructions
SMARTCASE S520
Assembly Instructions
SMARTCASE S520 & D3654-B / D3664-B
________________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________________________________
Page 1 of 12
V1.1 - 07/2019
www.fujitsu.com
Table of Contents
Related Manuals for Fujitsu SMARTCASE S520
Summary of Contents for Fujitsu SMARTCASE S520
- Page 1 Assembly Instructions SMARTCASE S520 Assembly Instructions SMARTCASE S520 & D3654-B / D3664-B ________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________ Page 1 of 12 V1.1 - 07/2019 www.fujitsu.com...
-
Page 2: Table Of Contents
Assembly Instructions SMARTCASE S520 Table of Contents Step 1 Preparing the Chassis ............................3 Step 2 Inserting additional Modules (Memory / M.2 / …)....................4 Step 3 Mainboard Assembly ............................6 Step 4 Installing the Heatsink ............................7 Step 5 Installing optional HDD Tray [updated] ....................... 8 Step 6 Optional Components ............................ -
Page 3: Step 1 Preparing The Chassis
Assembly Instructions SMARTCASE S520 Step 1 Preparing the Chassis Open the chassis with two hands by putting some pressure on your thumbs to push the cover reverse. Rear Cover Remove top cover and unpack the accessories. Remove the tape (transportation lock) of the thermal pad carefully! -
Page 4: Step 2 Inserting Additional Modules (Memory / M.2
Assembly Instructions SMARTCASE S520 Step 2 Inserting additional Modules (Memory / M.2 / …) The following picture shows some possible M.2 modules M.2 2230 WLAN + Antenna Mainboard Speaker + mount rubber SATA + Power cable 2,5” Storage / M.2 SSD 2280 Memory Attention: Do not touch any pins! Touch the memory at the outside edges only. - Page 5 Assembly Instructions SMARTCASE S520 WLAN module / M.2. module assembly First remove the M.2 mounting screws. 2230 screw / nut position 2280 screw / nut position Insert M.2 modules angular into the socket (while paying attention to the coding / notch).
-
Page 6: Step 3 Mainboard Assembly
Assembly Instructions SMARTCASE S520 Step 3 Mainboard Assembly 1. Slide in the mainboard carefully below the power button light towards the front I/O holes(red circle) 2. Move the mainboard carefully down to the final position Take care the thermal pad and the EMI gasket stay in the right position. -
Page 7: Step 4 Installing The Heatsink
Assembly Instructions SMARTCASE S520 Step 4 Installing the Heatsink Fujitsu provides an active heatsink solution. Before assembling the mainboard into the chassis, it is recommended to install the optional onboard components like cooler, RAM, M.2, etc. Active Heatsink Hold the heatsink with one hand so that it doesn’t tilt while installing the... -
Page 8: Step 5 Installing Optional Hdd Tray [Updated]
Assembly Instructions SMARTCASE S520 Step 5 Installing optional HDD Tray [updated] Install the SSD into the tray with four M3x3.5 srews (0.25Nm) and plug in the SATA/Power connectors. Plug the SATA and power cable to the onboard connectors. Then insert the HDD Tray carefully into the chassis and assemble the four screws (M3x4.5;... -
Page 9: Step 6 Optional Components
Assembly Instructions SMARTCASE S520 Step 6 Optional Components Installing WLAN Antennas Please check the color-coding of the antennas. On the chassis front side the antenna bays are marked black respectively gray . Please note that the plastic front bezel has to be removed first. -
Page 10: Speaker Assembly
Assembly Instructions SMARTCASE S520 Speaker Assembly Please note that the plastic front bezel has to be removed first. Speaker Rubber Speaker speaker location Insert speaker into “rubber” Install speaker / rubber in front bezel Speaker cable lead to mainboard via appropriate chassis aperture. -
Page 11: Step 7 Closing The Chassis [Updated]
Note: As the mainboard D3664-B provides an additional USB type-C port a different rear chassis wall is required for SMARTCASE S520. This chassis wall (K1056-B520) is included in the D3664-B mainboard delivery kit. __________________________________________________________________________________________________________________________________________________________ Page 11 of 12 V1.1 - 07/2019... -
Page 12: Step 8 Adding Stands
Assembly Instructions SMARTCASE S520 Step 8 Adding Stands The chassis kit includes a desk stand for vertical use and four rubber feet for horizontal use. They desk stand can be fixed by plastic clips, in addition there are screws included for more secure stand assembly.