Quick Links
General Installation Manual
General Installation Manual for SANYO HIT Photovoltaic (PV) Modules.
Please read this manual completely before installing or using the modules.
This manual is applied for the following products::w
INTRODUCTION
Thank you for choosing SANYO HIT PV
modules. With proper operation and
maintenance, SANYO HIT PV modules
will provide you with clean, renewable
solar electricity for many years.
Retain this manual for reference. This
manual contains important information
about installation, maintenance and
safety.
Please retain it for future reference.
Disclaimer of Liability
SANYO does not assume responsibility
and expressly disclaims liability for loss,
damage, or expense arising out of or in
any way connected with such installation,
operation use or maintenance by using
this manual.
SANYO assumes no responsibility for
any infringement of patents or other
rights of third parties that may result from
use of the module.
No license is granted by implication or
under any patent or patent rights. The
information in this manual is believed to
be reliable, but does not constitute an
expressed and implied warranty.
SANYO reserves the right to make
changes to the product, specifications, or
manual without prior notice.
General Information
The installation of solar modules requires
a great degree of skill and should only be
performed by qualified licensed
professional, including, without limitation,
licensed contractors and licensed
electricians.
W A R N I N G
All instructions should be read
and understood before attempting to
install, wire operate and maintain the
photovoltaic module. Contact with
electrically active parts of the module
such as terminals can result in burns,
sparks, and lethal shock whether the
module is connected or
disconnected.
The installer assumes the risk of
all injury that might occur during
installation, including, without
:w
:w
:w
HIP-190BE3, HIP-180BE3, HIP-175BE3, HIP-167BE3
limitation, the risk of electric shock.
PV modules generate DC
electrical energy when exposed to
sunlight or other light sources.
Although single modules produce
only a low voltage and current,
shocks and burns are still a potential
hazard.
To avoid the hazard of electric
shock and injury, cover all over the
front surface of PV modules with a
dense opaque material such as the
cardboard box during installing and
handling modules.
The shock hazard increases as
modules are connected in parallel
producing higher current. The
shock hazard increases as modules
are connected in series producing
higher voltages.
To avoid the hazard of electric
shock, work only under dry
conditions, with dry module and
tools.
Do not stand or step on a
module to avoid the hazard of injury
and the damage to a module.
Do not damage the back sheet of
a module, to avoid the hazard of
electric shocks and fire.
To avoid the hazard of electric
shock and injury, Children and
unauthorized persons should not be
allowed near the installation of the
solar cell modules.
To avoid the hazard of electric
shock and injury, be sure to ground
the modules completely.
To avoid the hazard of electric
shock, fire and injury, do not
disassemble the module, or remove
any part installed by the
manufacturer.
Unauthorized persons except
the qualified licensed professional
should not open the cover of the
junction box to avoid the hazard of
electric shock.
Do not touch terminals while a
module(s) is exposed to light.
Provide suitable guards to prevent
yourself contacting directly with 30
VDC or greater to avoid the hazard of
electric shock or injury.
When carrying a module, more
than two persons should carry it by
the frame and wear non-slip gloves to
avoid the hazard of injury by slipping
1
down the module on a foot or cutting
by an edge of the frame and so on.
Do not carry a module by wire or
junction box to avoid the hazard of
electric shock and injury or any
troubles in a module, which it may
cause.
Do not drop anything on the
surfaces of modules to avoid the
hazard of electric shock and injury or
any troubles that it may cause.
To avoid the hazard of electric
shock and fire, be sure that other
system components do not cause
any hazard of any mechanical or
electrical nature to the module.
Since sparks may be generated,
do not install module where
flammable gases or vapors are
present.
Never leave a module
unsupported or unsecured.
drop module and do not allow
objects to fall on module to avoid the
hazard of injury or any troubles in
modules that it may cause.
Do not use or install broken
modules to avoid the hazard of
electric shock and injury.
Do not artificially concentrate
sunlight on module to avoid the
hazard of fire or any trouble.
Do not touch the Junction box
terminals to avoid the hazard of
electric shock and injury.
Do not change wiring of bypass
diodes to avoid the hazard of electric
shock and injury.
CAUT IONS
Use module for its intended
function only.
Do not treat the back sheet and
front surface with paint or adhesives
to avoid any troubles.
Printed in Japan 04.09.22.000
Do not
Related Manuals for Sanyo HIP-190BE3
Summary of Contents for Sanyo HIP-190BE3
-
Page 1: General Information
General Installation Manual General Installation Manual for SANYO HIT Photovoltaic (PV) Modules. Please read this manual completely before installing or using the modules. This manual is applied for the following products::w HIP-190BE3, HIP-180BE3, HIP-175BE3, HIP-167BE3 INTRODUCTION limitation, the risk of electric shock. - Page 2 Metal fitting This section contains electrical and (4 places) mechanical specifications before using your SANYO photovoltaic modules. • Modules should be firmly fixed in place in a manner suitable to withstand all expected loads, including Mounting wind and snow loads.
-
Page 3: Specifications
Fig2. Then, a maximum loading of 2170N/m (45PSF, in static state) on the module surface is possible. CERTIFICATION Dimensions HIP-190BE3, 180BE3, 175BE3, (Module type : HIP-190BE3, -180BE3, -175BE3, -167BE3B¶B¶B¶ B¶B¶B¶ B¶B¶B¶ B¶B¶B¶ with connector and cable) 167BE3 Module comply with the... -
Page 4: Junction Box
(10). of electric shock or injury. • The following SANYO solar modules, HIP- 190BE3, 180BE3, 175BE3, 167BE3 are not designed to...