1. Manuals
  2. Brands
  3. GE Manuals
  4. Receiver
  5. GEC-4VDPBC
  6. Installation sheet

GE GEC-4VDPBC Installation Sheet

Hide thumbs
Table of Contents

Quick Links

GE
Security
Multi-Channel VPD Combiner
Receiver Installation Sheet
Introduction
GE Security Multi-Channel Video Power Data Combiner Receivers combine video,
PTZ data, and camera power over a single 4-pair UTP cable to simplify CCTV
installations in a structured wiring environment. They support up to 16 cameras
and should be installed in the control room.
The GEC-4VDPBC and GEC-16VDPBC need to be used along with external class II
power supplies. The GEC-8PVPDTCHUB and GEC-16PVPDTCHUB come with built-
in 8 and 16 channel fully isolated class II 24/28 VAC power supplies. Each camera
power output in addition to an auto-reset fuse is equipped with a 2 A glass fuse
that is easily accessible from the front panel.
At the camera end a video balun/combiner provides video, power and data on
separate outputs. The video connections are through BNC connectors to the DVR
or matrix switches. The data connections to the DVR are through RJ-45
connectors. There is a separate data connection for each camera. All equipment
follows industry-standard EIA/TIA 568B pin-outs.
The following model numbers are covered in this document:
•
GEC-4VDPBC
•
GEC-16VDPBC
•
GEC-8PVPDTCHUB
•
GEC-16PVPDTCHUB
1 of 11
P/N 1069686 • REV 1.0 • ISS 10MAR10
© 2010 GE Security, Inc.
Table of Contents
loading

Related Manuals for GE GEC-4VDPBC

Summary of Contents for GE GEC-4VDPBC

  • Page 1 They support up to 16 cameras and should be installed in the control room. The GEC-4VDPBC and GEC-16VDPBC need to be used along with external class II power supplies. The GEC-8PVPDTCHUB and GEC-16PVPDTCHUB come with built- in 8 and 16 channel fully isolated class II 24/28 VAC power supplies.

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with a dry cloth. 7) Do not block any ventilation openings. 8) Install in accordance with the manufacturer’s instructions.
  • Page 3 We recommend using short 18 AWG solid wires for ground connections. • GE VPD products follow the EIA/TIA 568 standard. There are two wire color- code standards: EIA/TIA 568A and EIA/TIA 568B. Either standard can be used for making connections as long as the RJ-45 jacks at both ends of each cable follow the same standard.

  • Page 4: Important Safety Warnings

    To reduce the risk of fire or electrical shock, do not expose these products to rain, moisture, dripping or splashing. • No objects filled with liquids, such as vases, shall be placed on GE equipment. • DO NOT block ventilation openings to let sufficient airflow to the UTP devices.

  • Page 5: Application Drawing

    Cat-5 Cable: Connect the RJ-45 connector attached to the camera end of Cat-5 cable to the RJ-45 Jack of the GE single combiner receiver. Make sure that the pin-out of the RJ-45 connector matches the pin-out of the GE single combiner receiver.
  • Page 6 DVR. Then run the outputs of the data distributor to RJ-45 data connectors of the combiner. You may need to use a 110 junction block to connect the output of the GE data distributor to the RJ-45 data connectors. Camera Cable: Connect each camera RJ-45 connector to the appropriate camera Cat-5 cable.

  • Page 7: Diagnostic Leds

    If (DVideo) > 750 feet Use a combiner at Mid-span location closer to the cameras. Use an active receiver hub at control room. Step 3: Use a single channel GE combiner transceiver on the camera side considering the camera voltage. Diagnostic LEDs...

  • Page 8: Technical Specifications

    GEC-8PVPDTCHUB: Extruded Aluminum and sheet metal GEC-16PVPDTCHUB: Extruded Aluminum and sheet metal Dimensions (W x H x D) GEC-4VDPBC: 4.97 x 1.74 x 1.77 in. (12.6 x 4.2 x 4.5 cm) GEC-16VDPBC: 18 x 1.74 x 1.77 in. (45.7 x 4.2 x 4.5 cm) GEC-8PVPDTCHUB: 17 x 1.74 x 10.5 in.

  • Page 9: Included Accessories

    Mounting brackets for front, rear or wall installations • Rubber feet for desk applications • 8 or 16 2 ft. (60 cm) coax jumper cables (excluding GEC-4VDPBC) • RJ-45 Adapters (excluding GEC-4VDPBC) • Molded IEC power inlet cord 7 ft. (200 cm) EIA/TIA 568A, B Color Codes P/N 1069686 •...
  • Page 10 Camera side RJ-45 Connections Control Room Data Connections Figure 2: GEC-4VDPBC (Cameras 1-4 only) 16VDPBC 8PVPDTCHUB 16PVPDTCHUB (Cameras 1–8) Figure 3: GEC-16VDPBC 16PVPDTCHUB (Cameras 9-16) 10 of 11 P/N 1069686 • REV 1.0 • ISS 10MAR10...

  • Page 11: Regulatory Information

    EU authorized manufacturing representative: GE Security B.V., Kelvinstraat 7, 6003 DH Weert, The Netherlands Regulatory N4131 information Note: C-Tick mark applies to models GEC-4VDPBC and GEC-16VDPBC only. North American UL 60065 standards FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

This manual is also suitable for:

Gec-16pvpdtchubGec-16vdpbcGec-8pvpdtchub

Table of Contents