Cisco TelePresence SX20 Quick Set Installation Sheet

Hide thumbs Also See for TelePresence SX20 Quick Set:

Quick Links

Installing Cisco TelePresence SX20 Quick Set
SX20 Quick Set components
SX20 Codec
HDMI cable for monitor
y
y
(1 default and 1 optional)
y
Camera options
y
Ethernet cable for LAN
A: PrecisionHD 1080p 12X
VGA to DVI-A cable
y
B: PrecisionHD 1080p 4XS2
for PC connectivity
y
Table Mic 20 microphone
y
Camera cable
(1 default and 1 optional)
Power supply and
y
Remote control and
y
power cable
four AAA batteries
y
Camera mounting bracket
In addition to the SX20 Quick Set you must provide a monitor or
projector, and a loudspeaker (external or built-in to the monitor) to
complete your video conferencing system.
User guides
A 级声明 (A Class product declaration)
User guides and compliance and safety information for this product,
is available at http://www.cisco.com/go/telepresence/docs.
Navigate to your product in the right pane; start by selecting
本产品为 A 级 ITE,在其使用说明,铭牌等显著位置中已包含如下内容的声明
TelePresence Solutions
Platform.
(We declare here that the subject product is A class ITE product, and the
following statement is clearly marked in the user manual or nameplate):
EMC Class A declaration
警告
此为 A 级产品。在生活环境中,该产品可能会造成无线电干扰。在这种
情况下,可能需要用户对干扰采取切实可行的措施。
WARNING:
WARNING:
This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be required to take
This is a class A product. In a domestic environment this
adequate measures.
product may cause radio interference in which case the user may be
required to take adequate measures.
78-20385-01 SX20 Quick Set Installation Sheet | 2011 DECEMBER | © 2011 Cisco Systems, Inc. All rights reserved.
声明所在位置 (Position of the Declaration):
使用说明 User Manual
Recommended room setup
The following should be regarded as
guidelines only. Try things out on-site
before fixing any mounting positions.
To learn more about optimizing your
office or meeting room for video
conferencing, please read the
Video
conferencing room primer
and
Guidelines for video conferencing
room acoustics
documents available
on our web site.
Place the camera just above
the monitor to enhance the
perceived eye contact.
If using the camera mounting
bracket, fasten it to the monitor
with the Velcro.
The lower edge of the monitor
should be vertically aligned with
the table top.
Monitors larger than 55" should
be placed slightly lower.
Camera option A:
Camera option B:
PrecisionHD 1080p 12X
PrecisionHD 1080p 4XS2
Snap on the lens hood to
The camera is
prevent stray light from
fastened to the bracket
disturbing your video
with a screw.
experience.
Tool: 4 mm Allen Key
The camera snaps to the
(not provided).
magnets on the bracket.
When placing the monitor and
camera, use the camera self
view function to make sure all
participants are captured by the
camera.
Aim for good illumination of a
person's face to avoid shadows.
Also avoid direct light on the
monitor to prevent reflections.
Place the microphone(s) as
close to all meeting participants
as possible.
loading

Summary of Contents for Cisco TelePresence SX20 Quick Set

  • Page 1 78-20385-01 SX20 Quick Set Installation Sheet | 2011 DECEMBER | © 2011 Cisco Systems, Inc. All rights reserved. 声明所在位置 (Position of the Declaration): 使用说明...
  • Page 2 When the button lights steadily (this may take a few minutes) the system is ready for configuration. 78-20385-01 SX20 Quick Set Installation Sheet | 2011 DECEMBER | © 2011 Cisco Systems, Inc. All rights reserved.