Summary of Contents for RAM XH-PCMS-H-SD
- Page 1 V E R TI CAL & HO RI ZO N AL CE MEN T M I X ER XH-PCMS-H-SD INSTRUCTION MANUAL I M POR TAN T : Pl eas e c are ful l y re ad this manua l b e fo re using this d e v ic e an d s ave this manu a l for fu ture re fe re nc e .
-
Page 2: Important Safety Instructions
IM POR TAN T S AF E T Y INST RU C T I ONS SAFETY GUIDELINES DEFINITIONS DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. -
Page 3: Electrical Safety
OBSERVE WORK AREA CONDITIONS (CONTINUED) WARNING: • Keep children and bystanders away while operating the cement mixer. • Work area should be clear of debris and obstructions. • Ensure all tools and other equipment are removed from area and he cement mixer drum before operating. -
Page 4: Personal Safety
PERSONAL SAFETY DANGER: • Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. • Do not place hands or tools (ie. shovel) in or around the drum while operating. Personal injury could occur. -
Page 5: Specifications
NOTE: • Keep the cement mixer clean. Clean after each use. • Ensure drum is rotating when filling or emptying the mixer. This ensures a good mix and prevents damage to the motor. • Be familiar with concrete mix being used, particularly quick set formulas. This is import- ant when motor overload protection shuts off the motor to prevent motor damage. -
Page 6: Parts Diagram
PAR T S D I AGR AM... -
Page 7: Parts Lists
PAR T S LIST S Item# Description QTY Item# Description Mixing Drum Motor and Gear Box Nut M12 Bolt (M10 x 75 mm) Washer Ø12 Washer Ø8 Screw (M12 x 21mm) Rear Stand Mixing Paddle Handle Large Cotter Pin Cover Nut 10”... - Page 8 A S SE MBLY 1. Insert left handle (19 into rear stand (18), align fixing hole with chassis (9) using screws (16), washers (17), nuts (20). Repeat for right hand side. (Fig. 1) DO NOT COMPLETELY TIGHTEN ALL FASTENERS 2. Assemble reinforced pole (22) between two handles (19) using washer (17), nuts (20).
- Page 9 A S SE MBLY 3. Slide the wheels (7) onto the axles of the frame (9), secure the wheels with the big cotter pins (6). (Fig. 3) 4. Attach the motor and gearbox assembly (15) via the four studs through the frame (9) using washers (23) and nuts (24).
- Page 10 5. To mount the Drum (1), align the Guide Notch at the bottom of the mixing Drum (1) to the Positioning Pin (28) on the gear box shaft. (Fig. 5 & Fig. 6) Guide Notch Fig. 6 Drum Positioning Pin T-Bolt...
- Page 11 Assembly Instructions (Continued) STEP 5: T-BOLT SLEEVE Tightly secure the Drum using the T-Bolt with T-Bolt Sleeve provided . Slide the Spring Washer (12) and T-Bolt Washer M14X5 mm (13) onto the T-Bolt (11) . Then slide the T-Bolt Sleeve (14) over the T-Bolt handle, see below .
-
Page 12: Before Use
OPER AT I ONS BEFORE USE • Before each use, inspect that the cotter pins are in place and that all nuts, bolts and screws are fully tight. • Inspect the product before each use for worn and damaged parts. Do not operate if you find broken and worn parts. -
Page 13: Maintenance
MAI N TE N AN CE NOTE: OVERLOAD POWER PROTECTOR • The motor has a thermal overload protector. If the motor overheats for any reason, the overload protector will shut off the motor. Unplug the cement mixer and allow te motor to cool down before restarting. -
Page 14: Troubleshooting
TR O U BLE SH O OTING ELECTRICAL PROBLEM RESOLUTION Check power connection. Connect if needed. Ensure the green ON (I) button is pressed. Motor does not run before loading concrete. Do not use an extension cord that is below 14AWG 3-Prong. -
Page 15: Warranty
WARR AN T Y 1-Year Limited Warranty This product is guaranteed for a period of one (1) year from the date of original retail purchase, against defects in materials and workmanship. Subject to the conditions and limitations described below, this product, if returned to us with proof of purchase within the stated warranty period and if covered under this warranty, will be repaired or replaced (with the same model, or one of equal value or specification), at our option. - Page 16 RAM International Enterprise Ltd / Inter-Pacific Trading Corp. #113 - 11280 TWIGG PLACE RICHMOND BC CANADA V6V0A6 www.raminternational.ca...