Table of Contents
Quick Links
Table of Contents
Summary of Contents for LG HECTO Series
- Page 1 Install Manual HECTO Series Screen (HECTO/HECTO2/HECTOB) Please read the safety information carefully before using this product. (Refer to this manual when installing the screen with the Ez bracket and the ceiling-type bracket.) SC200 www.lg.com *MFL67864907* P/NO.: MFL67864907 (1405-REV01)
-
Page 2: Safety Precautions
SAFETY PRECAUTIONS SAFETY PRECAUTIONS Please take note of safety instructions to prevent any potential accident or misuse of the product. Safety precautions are given in two forms, i.e. WARNING and CAUTION as detailed below. WARNING: Failure to follow the instructions may cause serious injury and even death. - Page 3 SAFETY PRECAUTIONS When drilling holes into the wall, make sure you use a drill and drill bit with the specified diameter. Ensure that you also follow the instructions regarding the depth of the holes. - Otherwise, this product may not be installed properly and cause safety issues.
- Page 4 PREPARATION PREPARATION Accessories Check the accessories provided with the product. The picture may be different from the actual product. Accessories are subject to change without prior notice in order to improve the performance of the product. New accessories may be added or old ones may be removed.
-
Page 5: Installation Position
PREVIEW OF THE SCREEN INSTALLATION PREVIEW OF THE SCREEN INSTALLATION Installation position The picture may be different from the actual product. Screen HECTO* Installation procedure Decide the desired position of your HECTO* screen and place the HECTO* in the center of the position. Attach the guide paper according to the HECTO*'s position. -
Page 6: Positioning The Screen
INSTALLING INSTALLING Positioning the screen Place the guide paper at a height of 1470 mm from the tabletop. Align the centers of the guide paper and the HECTO*. While keeping the guide paper level with the floor, attach it to the wall. Guide paper 1470 mm CAUTION... - Page 7 INSTALLING Drill the holes using the Ф 8 mm drill bit, according to the holes marked on the guide paper. Remove the paper and insert the anchors into all of the holes. Using the Ф 8 mm screws, fix the wall bracket on the wall while matching the reference dots and the holes.
- Page 8 INSTALLING Two people lift the screen and hang it onto the wall bracket while keeping the Up ar- row facing up. (When installing the ceiling type, attach the screen upside down while keeping the Up arrow facing down.) Down Back CAUTION Be careful not to scratch the film on the back of the screen.
- Page 9 INSTALLING Power on the HECTO* Activate the Test Pattern, referring to the user manual. When installing with the Ez bracket, make the projected image rectangular, referring to the User Guide for Correcting Image Distortion. (Without Ez brackets, move the HECTO* to make the projected image rectangular.) As shown below, adjust the position of the screen to match the projected image.
- Page 10 INSTALLING Aligning the screen by adjusting the screen height If you need to adjust the screen height, unscrew the wall brackets and move the refer- ence dots up or down and fix them again. The distance between two dots is 10 mm. (Height: adjustable up to + 40 mm upwards, and -30 mm downwards) Reference Dots...
- Page 11 INSTALLING Fixing the screen On the point that is 310 mm away from the both side edges and 28 mm high from the bottom edge, drill 8 mm holes and attach the space steels using the 8 mm screws. 310 mm 310 mm Attach three magnets to each of the steel spacers attached to the lower holes.
- Page 12 INSTALLING Installing with Ez Bracket Install the Ez bracket after completing all the screen installations in the order described below. Screen Wall Anchor Washer Bolt Ez braket Make holes on the wall and insert the anchors into the holes. Make sure that the anchors, washers and Ez bracket holes are in line and then tighten the bolts.
-
Page 13: Watching Images
INSTALLING Watching images When all the steps have been completed, the projected image matches the screen, as shown in the figure below. When the projected image is bent The screen may not be flat in some cases. If the projected image is bent, as shown below, even after all the adjustments have been made, attach one or more sponges or papers etc. - Page 14 FIXING THE ANCHORS AND SCREWS FIXING THE ANCHORS AND SCREWS Fixing the anchors and screws CAUTION Check the wall material and thickness of the finish material. You can use the included anchors and screws with the screen for walls made of concrete, lightweight concrete, soft fieldstone, hard fieldstone, brick, or hollow blocks.
-
Page 15: Specifications
SPECIFICATIONS SPECIFICATIONS 33 ± 1 mm (C) 2248 ± 5 mm (A) Model name SC200 A (width) 2248 mm ± 5 mm B (height) 1275 mm ± 3 mm C (thickness) 33 mm ± 1 mm Weight Up to 16 kg...