1. Manuals
  2. Brands
  3. Sony Manuals
  4. Motherboard
  5. BKP-5090
  6. Installation and maintenance manual

Sony BKP-5090 Installation And Maintenance Manual

Camera upgrade board
Hide thumbs

Quick Links

CAMERA UPGRADE BOARD
BKP-5090
INSTALLATION AND MAINTENANCE MANUAL
1st Edition (Revised 1)
loading

Summary of Contents for Sony BKP-5090

  • Page 1 CAMERA UPGRADE BOARD BKP-5090 INSTALLATION AND MAINTENANCE MANUAL 1st Edition (Revised 1)
  • Page 2 ! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
  • Page 3 For the customers in the U.S.A. and Canada CAUTION RECYCLING NICKEL-CADMIUM BATTERIES Danger of explosion if battery is incorrectly replaced. Nickel Cadmium batteries are Replace only with the same or equivalent type recyclable. You can help preserve our recommended by the manufacturer. environment by returning your unwanted Dispose of used batteries according to the batteries to your nearest point for...
  • Page 5 Manual Structure Purpose of this manual ..................5 (E) Contents ....................... 5 (E) Related manuals ....................6 (E) 1. Installation 1-1. Configuration of BKP-5090 ..............1-1 (E) 1-2. Installation Procedure................1-2 (E) 1-3. Installing the Backup battery ..............1-2 (E) 1-4. Attaching PR-242/AT-126 board to Camera ........1-3 (E) 1-5.
  • Page 6 Electrical Parts List ..................5-2 5-3. Supplied Accessories ................5-11 6. Semiconductor Pin Assignments 7. Block Diagrams Block Diagram Index .................. 7-1 BVP-550 Overall Block ................7-2 BVP-500 Overall Block ................7-4 PR-242 ......................7-8 AT-126 ...................... 7-10 2 (E) BKP-5090...
  • Page 7 8. Schematic Diagrams Schematic Diagram Index ................8-1 PR-242......................8-2 AT-126 ......................8-9 9. Board Layouts AT-126 ......................9-1 PR-242......................9-2 3 (E) BKP-5090...

  • Page 9: Manual Structure

    Section 1 Installation Describes the components that constitute the unit and the procedures to install the BKP-5090 in the color video camera BVP-500/500P/550/550P. Section 2 Electrical Alignment Describes electrical adjustment necessary after the unit is installed to BVP-500/ 500P/550/550P.
  • Page 10 When servicing the upgraded camera, see the BKP-5090 installation and maintenance manual and BVP-550/550P maintenance manual together..BVP-500/500P Operation Manual (Supplied with BVP-500/500P) This manual is necessary for application and operation of the BVP-500/500P.
  • Page 11 The BKP-5090 is the camera upgrade boards for the color video camera BVP-500/500P/550/550P. By installing the BKP-5090 in the camera, it will be upgraded to a 12-bit digital signal processing camera. To install proceed as follows. When upgrading the camera with the 16:9/4:3 switchable OHB incorporat- ed, the wide screen DSP board BKP-5091 (separately available) is also required.

  • Page 12: Installation Procedure

    Install the supplied battery into the battery holder (BT1) on the AT-126 board. Ensure that the battery is installed with “+” and “_” poles connected to the correct terminals. An improper connection may cause an explosion or leakage of fluid. 1-2 (E) BKP-5090...
  • Page 13 1-4. Attaching PR-242/AT-126 board to Camera If attaching the PR-242 board to the BVP-500/500P, a long-blade screwdriver (200 mm long or more) is required. Sony Part No.: 7-700-739-01 (or equivalent) 1. Open the both side panels. 2. Pull out the AT-95 board and insert the AT-126 board instead.
  • Page 14 (2) Attach the heat sink and the CN-1672 board (supplied with the unit) to the PR-242 board..BVP-550/550P Sheet B Radiation sheet Sheet A Heat sink PR-242 board B3 x 5 B3 x 4 CN-1672 board B3 x 5 Heat sink 1-4 (E) BKP-5090...
  • Page 15 B3 x 4 CN-1672 board 5. Place the UP GRADE label (supplied with the unit) as shown in the figure..BVP-550/550P ..BVP-500/500P UP GRADE label UP GRADE label 1-5 (E) BKP-5090...
  • Page 16 1-5. Modifying VA-163 Board 1-5. Modifying VA-163 Board The following are not supplied with the unit. Get them ready. Description Q’ty Sony Part No. Res, chip, metal 3.3 kZ 1-218-704-11 Res, chip, metal 15 kZ 1-218-720-11 Res, chip, metal 0 Z 1-216-295-11 1.
  • Page 17 6. Solder a 5 kZ variable resistor (RV1) between pin 16 of IC35 and R197. (See Fig. 2.) 7. Apply a Sony bond (glue) to variable resistor RV1 to fix it. 8. Cut the trace at pin 43 of CN1, then solder pins 43 and 44 of CN1. (See Fig.3.) 9.
  • Page 18 ROM version for IC10 on the CPU-171 board of the MSU-700 is Ver. 3.00 or higher and that the ROM versions for IC4 and IC5 on the AT-89 board of the CNU-700 are Ver. 2.70 or higher. If ROM replacement is required, please consult your local Sony Sales Office/Service Center. ROM Version [MSU-700] IC10/CPU-171 board Ver.
  • Page 19 Section 2 Electrical Alignment This section explains adjustment items required after the BKP-5090 is installed in the camera. Adjust- ment procedure differs depending on the camera in which the BKP-5090 is installed, BVP-500/500P or BVP-550/550P. Adjustments are performed by using the setup menu. For the setup menu operation, refer to Section 3 (for BVP-550/550P) or Section 4 (for BVP-500/500P).
  • Page 20 BVP-550/550P.) [BVP-500/500P/550/550P: By using the MSU-700 (for system use)] (1) Press and light the LEVEL button in the AUTO SETUP block of MSU. (2) Press and light the START/BREAK button in the AUTO SETUP block of MSU. 2-2 (E) BKP-5090...
  • Page 21 CCU-700A/700AP. Measuring equipment Oscilloscope: Tektronix 2465B or equivalent Waveform/Vector monitor: Tektronix 1750R or equivalent (for NTSC) Tektronix 1751R or equivalent (for PAL) Connection and settings during adjustment Refer to the BVP-550/550P maintenance manual, Section 4 for details. 2-3 (E) BKP-5090...
  • Page 22 Execute the file store. Press the MENU SEL switch twice referring to Section 4-3-3 “Test Out Adjustment” in to execute. the BVP-550/550P maintenance manual. MENU : Trimming File PAGE : Trimming File (T1) ITEM : File Store 2-4 (E) BKP-5090...
  • Page 23 (For PAL) monitor. File Store: Execute the file store. Press the MENU SEL switch twice to execute. MENU : Trimming File PAGE : Trimming File (T1) ITEM : File Store (For NTSC) (For PAL) 2-5 (E) BKP-5090...
  • Page 24 MENU : System config PAGE : Y/Chroma (S2) ITEM : SC-H Phase Specification : Position the luminous lines of the burst (SC) and the beam spot of H as shown in the figure. For NTSC) (For PAL) 2-6 (E) BKP-5090...
  • Page 25 : System config . RGB/ENC switch (on the side panel) → ENC PAGE : Y/Chroma (S2) ITEM : VF Specification : B = 100 ± 2 IRE (for NTSC) B = 700 ± 14 mV (for PAL) 2-7 (E) BKP-5090...
  • Page 26 4-3-7 “Test 1 Adjustment” in the BVP-550/550P maintenance manual and readjust each level for the above specifications. Resetting after the Confirmation: . Set the menu as follows. MENU : System config PAGE : PR/VA/Test (S3) : Test → Off ITEM 2-8 (E) BKP-5090...
  • Page 27 11. Set the menu as follows, and adjust the pre knee 1 for B by using the MENU SEL switch. Test Point : TEST OUT connector Adjustment Point: MENU : System config PAGE : PreKnee/Zebra (S4) ITEM : PreKnee1[B] Specification : Minimize the carrier leakage B. (Waveform Monitor) 2-9 (E) BKP-5090...
  • Page 28 1CT300/VA-163 board 1CT400/VA-163 board Specifications : B/A > 70 % 5 MHz 100 IRE (NTSC) 700 mV (PAL) TEST RV50 CT200 R GAIN (Waveform Monitor) RV200 CT300 G GAIN RV300 CT400 B GAIN RV400 VA-163 BOARD (A SIDE) 2-10 (E) BKP-5090...
  • Page 29 A = 400 ± 100 nS (NTSC) A = 1100 ± 100 nS (PAL) TP3 (Y) TP5 (B-Y) Resetting after Adjustment: Set the menu as follows. MENU : Paint PAGE : Video Level (P1) ITEM : Clear 2-11 (E) BKP-5090...
  • Page 30 Tektronix 1751R or equivalent 2. Set the menu as follows. (for PAL) MENU : System config PAGE : Y/Chroma (S2) Connection and settings during adjustment : CB → On ITEM Refer to the BVP-500/500P maintenance manual, Section 5 for details. 2-12 (E) BKP-5090...
  • Page 31 (For PAL) (Waveform Monitor) (20MHz B/W LIMIT → ON) File Store: Execute the file store. Throw the MENU SELECT switch twice to ENTER to execute. MENU : Trimming File PAGE : Trimming File (T1) ITEM : File Store 2-13 (E) BKP-5090...
  • Page 32 ENTER twice to execute. corresponding frames on the vector monitor. MENU : Trimming File PAGE : Trimming File (T1) ITEM : File Store (For NTSC) (For PAL) 2-14 (E) BKP-5090...
  • Page 33 : Y/Chroma (S2) : CB → On ITEM (For PAL) File Store: Execute the file store. Throw the MENU SELECT switch to ENTER twice to execute. MENU : Trimming File PAGE : Trimming File (T1) ITEM : File Store 2-15 (E) BKP-5090...
  • Page 34 5. Set the menu as follows and adjust the video level using the MENU SELECT knob/switch. Adjustment Point: MENU : System config PAGE : Y/Chroma (S2) ITEM : VF Specification : B = 100 ± 2 IRE (for NTSC) B = 700 ± 14 mV (for PAL) 2-16 (E) BKP-5090...
  • Page 35 6. If the specification is not satisfied, carry out Section 5-8 “Test 1 Adjustment” in the BVP-500/500P maintenance manual and readjust each level for the above specifications. Resetting after the Confirmation: TEST 1 button/MSU operation panel → OFF (Goes out) 2-17 (E) BKP-5090...
  • Page 36 . MASTER GAIN button/MSU operation panel → 0 dB . TEST 1 button/MSU operation panel → OFF (Goes out) . Set the menu as follows. MENU : Paint PAGE : W.Clip/Knee (P6) : Auto Knee → Off ITEM 2-18 (E) BKP-5090...
  • Page 37 1CT300/VA-163 board 1CT400/VA-163 board Specifications : B/A > 70 % 5 MHz 100 IRE (NTSC) 700 mV (PAL) TEST RV50 CT200 R GAIN (Waveform Monitor) RV200 CT300 G GAIN RV300 CT400 B GAIN RV400 VA-163 BOARD (A SIDE) 2-19 (E) BKP-5090...
  • Page 38 A = 400 ± 100 nS (NTSC) A = 1100 ± 100 nS (PAL) TP3 (Y) TP5 (B-Y) Resetting after Adjustment: Set the menu as follows. MENU : Paint PAGE : Video Level (P1) ITEM : Clear 2-20 (E) BKP-5090...
  • Page 39 PR-243 board 2-5. CCD Dynamic Range Adjustment Additional adjustment is required in order to obtain optimum CCD’s dynamic range in accordance with the serial number of OHB. For detail, see “Note” in the beginning of Section 1. 2-21 (E) BKP-5090...
  • Page 40 2. Storing the reference file After upgrading the camera by the BKP-5090, data stored as the reference file in the camera will become invalid and data stored in the setup card will, too. Restore the reference file after the following adjust- ments and settings are completed.
  • Page 41 Camera Adaptor CA-530/550/570 series Supply power from a camera control unit CCU-700A/700AP, AC adaptor AC-550/550CE or VTR..Switches and Button DISP switch DISP MENU MENU SEL switch LEVEL CANCEL button CANCEL 3-1 (E) BKP-5090...
  • Page 42 To confirm the ROM version easily proceed as follows: 1. Set the DISP switch to OFF. 2. Power the unit on while holding down the MENU SEL switch. The indication of ROM version is displayed for about three seconds. 3-2 (E) BKP-5090...
  • Page 43 Shifts vertically the location of the box cursor on the screen. Box WIDTH 00 to 99 ([41]) Sets the width of the box cursor. Box Hight 00 to 99 ([10]) Sets the height of the box cursor. 3-3 (E) BKP-5090...
  • Page 44 The change of aspect ratio using this menu is disabled because the CCU’ s setting has a priority when the CCU is connected. If you want to change the aspect ratio when the CCU is connected, use the Others page of the Paint menu. When you attempt to change using this menu, a message “Use Paint MNU” is displayed. 3-4 (E) BKP-5090...
  • Page 45 Press MENU SEL Sets the skin detail hue function automatically. switch to execute. (Locate the desired skin color within the gate marker of VF and measure.) Shaded pattern shows an area weighed in the auto-iris detection mode. 3-5 (E) BKP-5090...
  • Page 46 Select a lens file appropriate for the mounted lens from 16 kinds of the lens files which are stored in the RAM IC26/AT-126 board. An additional data such as a center marker is also stored in the selected lens file. 3-6 (E) BKP-5090...
  • Page 47 Press MENU SEL Sets all settings on the Detail 1 page to 0. switch to execute. (When you press MENU SEL switch, the “Clear” indication flashes. Press MENU SEL switch again to execute; press CANCEL button to cancel.) 3-7 (E) BKP-5090...
  • Page 48 Press MENU SEL Sets all settings on the Skin Detail page to 0. switch to execute. (When you press MENU SEL switch, the “Clear” indication flashes. Press MENU SEL switch again to execute; press CANCEL button to cancel.) 3-8 (E) BKP-5090...
  • Page 49 Press MENU SEL Sets all settings on the W.Clip/Knee page to 0. switch to execute. (When you press MENU SEL switch, the “Clear” indication flashes. Press MENU SEL switch again to execute; press CANCEL button to cancel.). 3-9 (E) BKP-5090...
  • Page 50 If the shutter mode selection is made both by the SHUTTER switch in the camera front and from the setup menu, last-set item is selected. If the Shutter and ECS are both set to ON in the menu, the ECS mode is automatically selected. And if the ECS and S-EVS are both set to ON, the S-EVS mode is. 3-10 (E) BKP-5090...
  • Page 51 Press the MENU SEL switch again to execute; press CANCEL button to cancel.) When the master modulation shading is adjusted, the V. Saw component for the R and B V-modulation shadings of the prism is simultaneously compensated. 3-11 (E) BKP-5090...
  • Page 52 Execute to recalculate. After execution, the color matrix data is temporarily reflected in the OHB matrix of the System config menu. Execute the OHB File Store of the Trimming File menu to store the color matrix data. 3-12 (E) BKP-5090...
  • Page 53 : Settings of Detail, Gamma and so on are returned as they were. Master _99 to 99 ([0]) Adjusts the master black in measuring the S/N ratio and modulation Black depth. [On], Off Detail [On], Off Chroma [On], Off Gamma [On], Off Matrix [On], Off Flare 3-13 (E) BKP-5090...
  • Page 54 ← Lens name Lens : 25 : A8.5 x 5.5 ← Lens extender value EX : 1.0 If the power is turned off without execution of the File Store after clearing the file, the original setting is restored. 3-14 (E) BKP-5090...
  • Page 55 1, 2, [Off] Test Selects a test signal to be output in setting each item on the PR/VR/ Test page. : Outputs the sawtooth test signal : Outputs the 3-step waveform test signal : No test signal is output 3-15 (E) BKP-5090...
  • Page 56 3 or C 5600 K 4300 K 4 or D 5600 K 6300 K y) The adjustment value is cleared by turning off and on the power sequentially because it is the temporary setting value for adjustment. 3-16 (E) BKP-5090...
  • Page 57 Execute the OHB File Store of the Trimming File menu to store the color matrix data. Adjust with the Matrix of the Paint menu turned OFF. Execute the OHB File Store of the Trimming File menu to store the adjustment values. 3-17 (E) BKP-5090...
  • Page 58 DISP switch set to ON when the self-diagnosis result is NG (no good) and so on. [RVS1], RVS 2, Off PinP RET RVS Selects the indication mode of VF display in PinP mode. (Does not function in the unit.) 3-18 (E) BKP-5090...
  • Page 59 (This function is sometimes not activated depending on the type of OHB which is incorporated in the camera.) [0], 6 dB Sensitivity 0: Normal mode 6: Select only when the gain is raised by 6 dB on the spot 3-19 (E) BKP-5090...
  • Page 60 Refer to the maintenance manual supplied with the camera adaptor for descriptions on columns of CA. When other equipment than the CA-550/550P/570/570P is connected to the camera, or when the CA-550/ 550P/570/570P is connected to the camera but is not connected to the CCU, the columns 8 will display “– –”. 3-20 (E) BKP-5090...
  • Page 61 RET 2 RET 1 POWER FILTER LOCAL CURSOR H-POSI V-POSI WIDTH HEIGHT STORE CENTER SAFETY PinP MENU SELECT MARKER ZONE UP TALLY MIX VF DISPLAY POSITION ENTER CALL MENU CANCEL MENU SELECT switch DISPLAY switch MENU SELECT knob 4-1 (E) BKP-5090...
  • Page 62 To confirm the ROM version easily proceed as follows: 1. Set the DISP switch to OFF. 2. Power the unit on while pushing up the MENU SELECT switch to ENTER. The indication of ROM version is displayed for about three seconds. 4-2 (E) BKP-5090...
  • Page 63 Shifts vertically the location of the box cursor on the screen. Box WIDTH 00 to 99 ([41]) Sets the width of the box cursor. Box Hight 00 to 99 ([10]) Sets the height of the box cursor. 4-3 (E) BKP-5090...
  • Page 64 The change of aspect ratio using this menu is disabled because the CCU’ s setting has a priority when the CCU is connected. If you want to change the aspect ratio when the CCU is connected, use the Others page of the Paint menu. When you attempt to change using this menu, a message “Use Paint MNU” is displayed. 4-4 (E) BKP-5090...
  • Page 65 Throw MENU SELECT Sets the skin detail hue function automatically. switch to ENTER (Locate the desired skin color within the gate marker of VF and measure.) to execute. Shaded pattern shows an area weighed in the auto-iris detection mode. 4-5 (E) BKP-5090...
  • Page 66 Fifty kinds of lenses are registered at the factory in the ROM IC26/AT-126 board. Up to 16 of these lenses can be stored as the lens file in the RAM IC26/AT-126 board. An additional data such as a center marker is also stored in the selected lens file. 4-6 (E) BKP-5090...
  • Page 67 Sets all settings on the Detail 1 page to 0. switch to ENTER (When you throw MENU SELECT switch to ENTER, the “Clear” to execute. indication flashes. Throw MENU SELECT switch to ENTER again to execute; throw to CANCEL to cancel.) 4-7 (E) BKP-5090...
  • Page 68 Sets all settings on the Skin Detail page to 0. switch to ENTER (When you throw MENU SELECT switch to ENTER, the “Clear” to execute. indication flashes. Throw MENU SELECT switch to ENTER again to execute; throw to CANCEL to cancel.) 4-8 (E) BKP-5090...
  • Page 69 Sets all settings on the W.Clip/Knee page to 0. switch to ENTER (When you throw MENU SELECT switch to ENTER, the “Clear” to execute. indication flashes. Throw MENU SELECT switch to ENTER again to execute; throw to CANCEL to cancel.) 4-9 (E) BKP-5090...
  • Page 70 The aspect ratio normally corresponds to the CCU’s setting when the CCU is connected. To forcibly select, use this menu. u) If the Shutter and ECS are both set to ON in the menu, the ECS mode is automatically selected. And if the ECS and S-EVS are both set to ON, the S-EVS mode is. 4-10 (E) BKP-5090...
  • Page 71 Throw MENU SELECT switch to ENTER again to execute; throw to CANCEL to cancel.) When the master modulation shading is adjusted, the V. Saw component for the R and B V-modulation shadings of the prism is simultaneously compensated. 4-11 (E) BKP-5090...
  • Page 72 Execute to recalculate. After execution, the color matrix data is temporarily reflected in the OHB matrix of the System config menu. Execute the OHB File Store of the Trimming File menu to store the color matrix data. 4-12 (E) BKP-5090...
  • Page 73 : Settings of Detail, Gamma and so on are returned as they were. _99 to 99 ([0]) Master Black Adjusts the master black in measuring the S/N ratio and modulation depth. [On], Off Detail [On], Off Chroma [On], Off Gamma [On], Off Matrix [On], Off Flare 4-13 (E) BKP-5090...
  • Page 74 No. : 1 ← Lens name to execute. Lens:25:A8.5 x 5.5 ← Lens extender value EX: 1.0 If the power is turned off without execution of the File Store after clearing the file, the original setting is restored. 4-14 (E) BKP-5090...
  • Page 75 1, 2, [Off] Test Selects a test signal to be output in setting each item on the PR/VR/ Test page. : Outputs the sawtooth test signal : Outputs the 3-step waveform test signal : No test signal is output 4-15 (E) BKP-5090...
  • Page 76 3 or C 5600 K 4300 K 4 or D 5600 K 6300 K y) The adjustment value is cleared by turning off and on the power sequentially because it is the temporary setting value for adjustment. 4-16 (E) BKP-5090...
  • Page 77 Execute the OHB File Store of the Trimming File menu to store the color matrix data. Adjust with the Matrix of the Paint menu turned OFF. Execute the OHB File Store of the Trimming File menu to store the adjustment values. 4-17 (E) BKP-5090...
  • Page 78 Camera output RET 1 (2, 3) video Camera output is displayed on the whole screen. (Small screen is not displayed.) * To output RET 3 video signal, press RET 1 and 2 switches at the same time. 4-18 (E) BKP-5090...
  • Page 79 (This function is sometimes not activated depending on the type of OHB which is incorporated in the camera.) [0], 6 dB Sensitivity 0: Normal mode 6: Select only when the gain is raised by 6 dB on the spot 4-19 (E) BKP-5090...
  • Page 80 RF is out of specs. * • Improper connection of the board * Only when no video signal is input. When the BVP-500/500P is not connected to the CCU, the columns 8,9 and 0 will display “– –”. 4-20 (E) BKP-5090...
  • Page 81 Spare Parts 5-1. Notes on Repair Parts 1. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. Parts list has the present standardized repair parts.
  • Page 82 8-759-711-50 s IC NJU7022M 1-135-157-21 s TANTALUM, CHIP 10uF 10% 6.3V LOT NO. 803 through 901 IC12 8-759-711-50 s IC NJU7022M 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V BKP-5090...
  • Page 83 1-216-794-11 s METAL, CHIP 5.6 5% 1/16W 1-216-829-11 s METAL, CHIP 4.7K 5% 1/16W 1-216-864-11 s METAL, CHIP 0 5% 1/16W 1-216-829-11 s METAL, CHIP 4.7K 5% 1/16W 1-216-821-11 s METAL, CHIP 1K 5% 1/16W 1-216-864-11 s METAL, CHIP 0 5% 1/16W BKP-5090...
  • Page 84 1-216-841-11 s METAL, CHIP 47K 5% 1/16W R136 1-216-841-11 s METAL, CHIP 47K 5% 1/16W R137 1-216-821-11 s METAL, CHIP 1K 5% 1/16W R138 1-216-809-11 s METAL, CHIP 100 5% 1/16W R139 1-216-821-11 s METAL, CHIP 1K 5% 1/16W BKP-5090...
  • Page 85 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V C123 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V C124 1-113-682-11 s TANTALUM, CHIP 33uF 20% 10V C125 1-113-682-11 s TANTALUM, CHIP 33uF 20% 10V C126 1-162-974-11 s CERAMIC, CHIP 0.01uF 50V BKP-5090...
  • Page 86 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V C245 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V C184 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V C246 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V C185 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V C247 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V BKP-5090...
  • Page 87 8-759-471-89 s IC 74VHC02MTCX IC22 8-759-086-41 s IC X24C02S-3.0 C337 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V IC23 8-759-996-82 s IC MSM82C55A-2GS C338 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V C339 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V C340 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V BKP-5090...
  • Page 88 1-218-723-91 s METAL, CHIP 20K 0.50% 1/16W 1-410-385-11 s INDUCTOR, CHIP 22uH 1-218-724-11 s METAL, CHIP 22K 5% 1/16W 1-410-373-31 s INDUCTOR CHIP 2.2uH 1-218-692-11 s METAL, CHIP 1K 0.50% 1/16W L400 1-410-389-31 s INDUCTOR, CHIP 47uH 1-218-692-11 s METAL, CHIP 1K 0.50% 1/16W BKP-5090...
  • Page 89 1-218-668-11 s METAL, CHIP 100 0.50% 1/16W R169 1-218-714-11 s METAL, CHIP 8.2K 0.50% 1/16W 1-218-644-11 s METAL, CHIP 10 0.50% 1/16W R170 1-218-728-11 s METAL, CHIP 33K 0.50% 1/16W 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W R171 1-218-716-11 s METAL, CHIP 10K 0.50% 1/16W BKP-5090...
  • Page 90 1-218-693-11 s METAL, CHIP 1.1K 0.50% 1/16W R510 1-215-437-00 s METAL 4.7K 1% 1/6W R236 1-218-660-91 s METAL, CHIP 47 0.50% 1/16W LOT NO. 902 and higher R238 1-218-644-11 s METAL, CHIP 10 0.50% 1/16W R239 1-218-644-11 s METAL, CHIP 10 0.50% 1/16W 5-10 BKP-5090...
  • Page 91 1-239-409-11 s RESISTOR BLOCK, CHIP 47X4 RB48 1-239-409-11 s RESISTOR BLOCK, CHIP 47X4 RB49 1-239-409-11 s RESISTOR BLOCK, CHIP 47X4 1-241-828-21 s RES, ADJ, METAL 500 1-241-828-21 s RES, ADJ, METAL 500 1-241-828-21 s RES, ADJ, METAL 500 5-11 BKP-5090...
  • Page 93 TL064CPW-E05 ....6-16 XN6534 ......6-2 MB88351PFV-ER ... 6-13 TL084CPW-E05 ....6-17 XN6534-TW ...... 6-2 MC74HC4052DTR2 ..6-8 TL084CPW-E20 ....6-17 MC74HC4053DTR2 ..6-18 TLC0820ACDW ....6-17 MSM82C55A-2GS ..6-13 TLC0820ACDWR .... 6-17 MSM82C55A-2GS-VK ..6-13 UPD4702G ..... 6-17 BKP-5090...
  • Page 94 74LCX32MTCX (NS)FLAT PACKAGE 74VHC32MTCX (NS)FLAT PACKAGE C-MOS QUAD 2-INPUT OR GATES —TOP VIEW— —TOP VIEW— 2SK853-K5 2SK853-T1K5 —TOP VIEW— Y = A + B = A • B XN6501 XN6501-TW XN6534 XN6534-TW 0 : LOW LEVEL 1 : HIGH LEVEL BKP-5090...
  • Page 95 2 - 13 EN = • • EN3 : LOW LEVEL 12-BIT ERROR ANA+ 3-STATE PIPELINED : HIGH LEVEL CORRECTION D0 - D11 OUTPUTS ANA_ A/D CONVERTER LOGIC : DON’T CARE REFERENCE LADDER AND DRIVER REFERENCE AND MODE SELECT BKP-5090...
  • Page 96 AD8041AR (AD)FLAT PACKAGE CXD1171M (SONY)FLAT PACKAGE AD8041AR-REEL CXD1171M-TH 160 MHz RAIL-TO-RAIL OPERATIONAL AMPLIFIER WITH DISABLE C-MOS 8-BIT D/A CONVERTER —TOP VIEW— —TOP VIEW— : DISABLE/POWER DOWN INPUT VREF IREF : CLOCK INPUT VREF : BLANKING PULSE INPUT D0 - 7...
  • Page 97 CXD2306Q (SONY) CXD2307R-T4 (SONY)FLAT PACKAGE CXD2307R-T6 C-MOS 10-BIT 1CH D/A CONVERTER —TOP VIEW— C-MOS 10-BIT 50 MSPS RGB 3CHANNEL D/A CONVERTER —TOP VIEW— 25 AGND DGND DGND VREF SREF IREF : BLANKING PULSE INPUT SIGNAL SIGNAL : CHIP ENABLE : CLOCK INPUT...
  • Page 98 CXD8354R (SONY) C-MOS DIGITAL ENCODER/GENLOCK —TOP VIEW— INPUT : 18 MHz CLOCK : 2fH : 36 MHz CLOCK ARDTI : AREA DETECT PULSE/SKIN TONE GATE ASET : IIC ASET : BURST FLAG BLKG : BLANKING BY0 - BY10 : B-Y DATA...
  • Page 99 CXD8355AR (SONY) HC-MOS AUTO WHITE/BLACK SHADING CORRECTION —TOP VIEW— INPUT ASET : IIC ASET B0 - B9 : B CHANNEL : 18 MHz CLOCK : POWER ON RESET G0 - G9 : G CHANNEL : HORIZONTAL SYNC R0 - R9...
  • Page 100 CXD8933AR (SONY) C-MOS IMAGE ENHANCER —TOP VIEW— INPUT BI00 - BI11 : B CHANNEL VIDEO DATA : CLOCK EXTSC : EXTERNAL SUBCARRIER EXTSYNC : EXTERNAL SYNC FSC4 : 4 fsc GI00 - GI11 : G CHANNEL VIDEO DATA : HORIZONTAL DRIVE...
  • Page 101 CXD8934AR (SONY) C-MOS PROCESSER —TOP VIEW— INPUT BPI00 - BPI11 : B CHANNEL SIGNAL : L: PARALLEL I/O CHIP ENABLE : MASTER CLOCK DTL00 - DTL11 : DETAIL GPI00 - GPI11 : G CHANNEL SIGNAL : HORIZONTAL DRIVE : IRIS CPU PRESENCE...
  • Page 102 CXD9058R (SONY) C-MOS ASPECT RATIO CONVERTER —TOP VIEW— INPUT : SCAN TEST ATG MODE CABI0 - CABI3 : RINGING CONTROL COEFFICIENT CCI0 - CCI3 : RINGING CONTROL COEFFICIENT CK1I, CK2I : CLOCK DLI0, DLI1 : DELAY SIGNAL : HORIZONTAL DRIVE...
  • Page 103 : OUTPUT ENABLE INPUT I/O5 I/O6 I/O7 MODE I/O TERMINAL I/O8 NOT SELECT HIGH IMPEDANCE NOT SELECT HIGH IMPEDANCE OUTPUT DISABLE HIGH IMPEDANCE READ OUTPUT DATA WRITE INPUT DATA : LOW LEVEL : HIGH LEVEL : DON’T CARE 5 30 6-11 BKP-5090...
  • Page 104 32 k BYTE CONTROLLER INTERRUPT CONTROLLER DATA TRANSFER CONTROLLER EXTAL SERIAL XTAL 8-BIT COMMUNICATION TIMER INTERFACE STBY 16-BIT FREE PWM TIMER RUNNING TIMER (x 3 CHANNEL) (x 3 CHANNEL) 10-BIT WATCHDOG A/D CONVERTER TIMER PORT 9 PORT 8 PORT 7 6-12 BKP-5090...
  • Page 105 TC7S00FU(TE85R) (TOSHIBA)CHIP PACKAGE OPEN C-MOS 2-INPUT NAND GATE —TOP VIEW— GND 4 CONT. INPUT GND 3 Y = A • B = CHANNEL : LOW LEVEL : HIGH LEVEL OPEN : DON’T CARE : LOW LEVEL : HIGH LEVEL 6-13 BKP-5090...
  • Page 106 : LATCH CLOCK INPUT —TOP VIEW— : SHIFT CLOCK INPUT RESET : SHIFT-REGISTER RESET INPUT : SERIAL N QA - QH : PARALLEL OUTPUT : SERIAL OUT RESET CONT. IN CHANNEL : LOW LEVEL : HIGH LEVEL : DON’T CARE 6-14 BKP-5090...
  • Page 107 —TOP VIEW— TC7SH04FU (TOSHIBA)CHIP PACKAGE Y = A • B = A + B GND 3 TC7SH04FU-TE85R C-MOS INVERTER —TOP VIEW— 0 : LOW LEVEL 1 : HIGH LEVEL GND 3 0 : LOW LEVEL 1 : HIGH LEVEL 6-15 BKP-5090...
  • Page 108 GND 4 : WRITE CONTROL INPUT/OUTPUT : SERIAL DATA INPUTS OUTPUTS FUNCTION Qn+1 Qn+1 CLEAR PRESET NOTE : – TYPE PIN 7 – : LOW LEVEL NM24C16 – : HIGH LEVEL X24C02 NO CHANGE : DON’T CARE X24C04 TEST 6-16 BKP-5090...
  • Page 109 TL084CPW-E20 (TI)FLAT PACKAGE RESET : COUNTER RESET INPUT : LATCH STROBE SIGNAL INPUT OPERATIONAL AMPLIFIER (J FET INPUT) —TOP VIEW— RESET CARRY PHASE 8-BIT DISCRIMINATION UP/DOWN COUNTER EDGE DETECTOR BORROW 8-BIT LATCH TRI-STATE OUTPUT 12-15 CD0 - CD7 6-17 BKP-5090...
  • Page 110 B BLK MC74HC4053DTR2 (MOTOROLA)FLAT PACKAGE VCBL C-MOS TRIPLE 2-CHANNEL ANALOG MULTIPLEXER/DEMULTIPLEXER —TOP VIEW— OPEN OPEN OPEN = +3 V to +12 V < GND CONTROL INPUTS SELECT ON CHANNEL : LOW LEVEL : HIGH LEVEL OPEN : DON’T CARE 6-18 BKP-5090...
  • Page 111 Index Section 7 Block Diagrams Block Diagram Index Page BVP-550 Overall Block ..........7-2 BVP-500 Overall Block ..........7-4 PR-242 ................7-8 AT-126 ................. 7-10 BKP-5090...
  • Page 112 ABNORMAL WHITE SW-730 TIME G TALLY DISP/MENU CLOCK MENU MENU SG-234 AT-126 C DATA MONI EXP. CONTROL C DATA SHUTTER EXP. AWB/ABB VF CONTROL SW-732 ENC/RGB RM VSB(X) START /STOP AUDIO CH1 CONT 1120 CONTROL INCOM LEVEL SW-731 CN-1122 BKP-5090...
  • Page 113 TALLY TALLY GEN LOCK(G)/H CONT DRIVE H CONT TALLY ON V RESET/CF CONTROL CONTROL REC TALLY REC TALLY IF-510 C DATA VF CONTROL VF CONTROL BATT ALARM RM VSB(X) RM VBS(X) 1120 CONTROL 1120 CONTROL CN-1120 BVP-550 Overall Block BKP-5090...
  • Page 114 S200 S503 EXP. DISPLAY ENTER S201 CANCEL MENU SELECT POSITION EXP. S202 S504 PIN P S505 STORE FILTER LOCAL S203 D502 SPARE SW-795 BKP-5090...
  • Page 115 TALLY ON IF-538 BVP-500 Overall Block (1/2) BKP-5090...
  • Page 116 AU-211 BKP-5090...
  • Page 117 SCRIPT FUSE PGM(X) INTERCOM UNREG(SCRIPT) INCOM VR INTERCOM EXT DC PGM VR INCOM 7.5V ENG/PROG +48V ENG/ +24V PROG INCOM 1 MIC ON +7.5V MIC ON PS-392 SW-805 RM SD REMOTE2 CN-1239 CHU UP TALLY LE-130 BVP-500 Overall Block (2/2) BKP-5090...
  • Page 118 VA, 1-89 36MHz (X) IN 1-126 +3.1V POWER ON 172-174 BFB0-2 2-12 VA, 1-58 B FEEDBACK OUT RESET2 GEN. IC30, 32-35, 38 159, 161-165 IC43 167-169 TST0-8 TEST SAW (X) OUT 2-21 VA, 1-26 SG, 1-61 1-109 36MHz (X) OUT BKP-5090...
  • Page 119 CHAR VF IN 1-44 AT, 1-28 IC30 CHRGT CHAR BACK IN 1-46 AT, 1-27 IC69 IC30 IC30 MKBC CURSOR2 OUT 1-45 IF, 1-9 5, 6 MARK CURSOR1 OUT 1-43 IF, 1-10 IC63 PR-242 18MHz (X) OUT 1-107 SG, 1-59 BKP-5090...
  • Page 120 VTR S/S OUT 1-52 MB, 12-6 Q3 (1/2) BUFF PET EN OUT 1-50 MB, 12-15 IC15 WINDOW OUT 1-45 IF, 1-25 FTOA2 FTOA1 V RESET OUT 1-23 SG, 1-21 FTOA3 PEAK RST OUT 1-46 IF, 1-26 AT-126 CONTROL BUS 7-10 7-10 BKP-5090...
  • Page 121 Index Section 8 Schematic Diagrams Schematic Diagram Index Page PR-242 ................8-2 AT-126 ................8-9 BKP-5090...
  • Page 122 0.001 100k R354 C345 C700 CN2(15/24) B(G) IN REFT C346 3.1V R353 R352 4.7k 2.5V VREF R351 C108 IC18 74LCX541MTCX IC73 P2,5 TC4W53FU(TE12R) PR-242 (1/5) -2.5V B/0-11 P3,5 BOARD NO. 1-669-860-11 NOTE: LOT NO. 803- NM: NO MOUNT B-¥BKP5090-PR242-11 BKP-5090...
  • Page 123 SN74HCT244APW-E0 5 CN2(24/24) MB,23-13 H CLP IN R506 PR-242 (2/5) CN1(47/140) VA,1-8/AT,1-22/SG,1-38 A HD OUT CN1(49/140) VA,1-7/AT,1-24/SG,1-37 A VD OUT BOARD NO. 1-669-860-11 NOTE: LOT NO. 803- IC69(6/8) IC69(5/8) HDVD1 P3,5 NM: NO MOUNT SN74HCT244APW-E0 5 SN74HCT244APW-E0 5 B-¥BKP5090-PR242-11 BKP-5090...
  • Page 124 RO09 DTL07 2.5V 2.5V 2.5V C125 :TA-CB C179 C200 C156 :TA-CB C184 C192 :TA-CB 2.5V :TA-CB 2.5V 2.5V 2.5V P1,5 B/0-11 P1,5 G/0-11 IC41(1/4) 74LCX32MTCX P1,5 R/0-11 2.5V C167 IC41(4/4) IC41(3/4) 74LCX32MTCX 74LCX32MTCX IC41(2/4) 74LCX32MTCX HDVD2 VFDTL0-9 P2,4 CLK3 BKP-5090...
  • Page 125 18 B-Y5 C226 36M(G)OUT S CK OUT :TA-CB B-Y4 B-Y4 B-Y3 B-Y3 B-Y2 B-Y2 B-Y1 B-Y1 TO/FROM PR-243(CN-1672) HDVD3 B-Y0 13 B-Y0 SKINGATE PA/0-8 PD/0-7 RB-Y PR-242 (3/5) BOARD NO. 1-669-860-11 LOT NO. 803- NOTE: NM: NO MOUNT B-¥BKP5090-PR242-11 BKP-5090...
  • Page 126 DA,1-76 Q405 R454 R183 SREF CN1(118/140) R170 -2.5V 2SA1611T1-M5M6 1.8k R188 HI-Y(G) OUT VREF 4.8V R167 IC64 HI-Y DVss DVss AVss AD8041AR-REEL 2SA1226-T1E3E4 -2.5V R186 C208 R171 C194 C196 R174 C206 4.3k 3.3k 6.3V C211 R187 1.5k P2,3,5 SDA0 BKP-5090...
  • Page 127 2.5V C233 RB27 RB37 CN1(44/140) CHAR VF IN AT,1-28 CN1(46/140) CHAR BACK IN AT,1-27 CN1(40/140) TITLE IN AT,1-26 CN1(42/140) TITLE BACK IN AT,1-25 PR-242 (4/5) RB28 IC72(2/4) 74LCX32MTCX NOTE: BOARD NO. 1-669-860-11 NM: NO MOUNT LOT NO. 803- BKP-5090 B-¥BKP5090-PR242-11...
  • Page 128 PR-242 (5/5) C169 ASET CN2(12/24) RB13 B FEEDBACK VA,1-58 C144 C152 C153 C154 -2.5V CN2(13/24) B SHADING GND BOARD NO. 1-669-860-11 TEST CN2(21/24) TEST SAW(X) OUT VA,1-26 CN2(22/24) LOT NO. 803- TEST SAW GND NOTE: B-¥BKP5090-PR242-11 NM: NO MOUNT P1,2 BKP-5090...
  • Page 129 :RN-C :RN-C AUDIO 0.01 IC12(2/2) IC12(1/2) IC13 NJU7022M-TE2 NJU7022M-TE2 MB88351PFV-ER 560k R164 R165 300k 330k 1/16W 1/16W AT-126 (1/2) 0.01 560k 270k BOARD NO. 1-670-466-11 NOTE: 0.01 NM: NO MOUNT LOT NO. 803- CN1(61/100) MB,32-5 IRIS CONT OUT B-¥BKP5090-AT126-11 BKP-5090...
  • Page 130 PR,1-52 R92 10 CN1(30/100) WR(PR) PR,1-50 R93 10 CN1(40/100) CE0(PR) PR,1-70 IC23(1/2) R94 10 CN1(29/100) CE1(PR) PR,1-48 TC74VHC20FT(EL) R95 10 CN1(42/100) A0(PR) PR,1-72 R96 10 CN1(41/100) A1(PR) PR,1-74 14 15 16 17 18 19 20 IC39 TC74VHC244FT(EL) 8-10 8-10 BKP-5090...
  • Page 131 MB,12-17 R151 R152 R153 100p 100p 100p 100k CN1(49/100) BATT ALARM IN MB,31-A4 R154 100p R155 NOTE: 100k CN1(80/100) MB,31-B7 NM: NO MOUNT Q3(2/2) CN1(79/100) IMH2-T110 NC(VF 7) AT-126 (2/2) BOARD NO. 1-670-466-11 LOT NO. 803- B-¥BKP5090-AT126-11 8-11 8-11 BKP-5090...
  • Page 133 * B4 R111 R112 * B4 R113 * A2 R114 * A2 R115 * B4 R116 * A2 R117 * A2 R118 *F4 * A2 R119 *F4 * B1 R120 *F4 R121 *G2 * A3 R122 * B3 R123 *G2 BKP-5090...
  • Page 134 R194 *E4 R454 * D7 * F3 C186 C290 C187 C291 *D2 IC35 * A5 Q407 * C7 R195 *D4 R455 * C7 * F3 C188 C300 *D2 IC36 * A3 Q408 * D7 R196 *E4 R456 * C7 BKP-5090...
  • Page 135 IC56 IC55 IC46 C162 R456 C181 C134 R408 C191 C173 R170 R404 RB12 L401 C269 C266 C268 C265 C186 C133 R104 C176 Q402 C197 C195 C208 R406 PR-242 PR-242 -A SIDE- -B SIDE- SUFFIX : -11 SUFFIX : -11 BKP-5090...
  • Page 137 Dies ist eine Einrichtung, welche die Funk-Entstörung nach Klasse B besitzt. The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual.
  • Page 138 Printed in U.S.A. Sony Corporation BKP-5090 (SY) J, E 1999. 6 76 Broadcasting & Professional Systems Company 3-200-629-02 ©1998...