ABB Magne 3 Series Excerpts From The Original Instructions

ABB Magne 3 Series Excerpts From The Original Instructions

Electromagnetic process lock
Hide thumbs Also See for Magne 3 Series:
Table of Contents
Available languages

Available languages

Quick Links

Excerpts from the original instructions
Magne 3 and 4
– Electromagnetic process lock
The complete Product Manual can be
found at:
www.abb.com/jokabsafety
[EN]
General description
Magne is an electromagnetic process lock that locks a door or hatch with a holding
force of up to 1500 N.
Magne 3 keeps a door locked to protect a process from unwanted interruptions. It
needs to be complemented by external interlocking devices if used in safety
applications.
Magne 4 has an integrated Eden sensor, which provides a high safety level of guard
interlocking protection. Magne 4 is available with built-in Adam DYN (DYNlink) or
Adam OSSD using an M12-5 or M12-8 connector.
Magne can be mounted on a door or a hatch with a JSM mounting kit, available for
either sliding doors or conventional doors (5–15 mm door gap). Y-connectors can be
used to connect several units. Magne 4 requires an Eva (which uses either a general or
unique code), an anchor plate “32B” (with built-in permanent magnet) or “32A”
(without permanent magnet) and a cellular rubber.
Electrical connections
M12 5-pole connector
M12 5-pole connector
M12 8-pole connector
1) Brown: +24 VDC
1) Brown: Locking signal +24 VDC
1) White: DYNlink signal in
2) White: DYNlink signal in
2) White: Not used
2) Brown: +24 VDC
3) Blue: 0 V
3) Blue: 0 V
3) Green: Locking signal +24 VDC
4) Black: DYNlink signal out
4) Black: Not used
4) Yellow: 0 V
5) Grey: Locking signal +24 VDC
5) Grey: Info output, locked
5) Grey: Info output (Eden &
locked)
6) Pink: DYNlink signal out
7) Blue: 0 V
8) Red: Not used
Warning! The info output is
non-failsafe and shall therefore
never be used to control a safety
application.
Warning! The safe signals
from the interlocking device Eden
are used to control the safety
application.
M12 8-pole connector
M12 8-pole connector
Warning! Always use shielded
1) White: OSSD1 Out
cables to connect the unit to the
2) Brown: +24 VDC
1) White: DYNlink signal in
rest of the safety circuit.
3) Green: OSSD1 in
2) Brown: +24 VDC
4) Yellow: OSSD2 in
3) Green: Locking signal +24 VDC
Note! Several Magne 3X units
5) Grey: Info output (Eden &
4) Yellow: 0 V
(using a M12-3A) or Magne OSSD-
Locked)
5) Grey: Info output (Eden)
Info units (using a M12-3G) can be
6) Pink: OSSD2 Output
6) Pink: DYNlink signal out
connected, but the info-signal will
7) Blue: 0 V
7) Blue: 0V
not be available.
8) Red: Locking signal +24 VDC
8) Red: Info output (Locked)
Installation
Warning! Magne shall be installed by a trained electrician following the Safety
regulations, standards and the Machinery directive. Installation shall be done in
accordance with a risk assessment for the individual application. Failure to comply
with instructions, operation that is not in accordance with the use prescribed in the
instructions, improper installation or handling of the device can affect the safety of
people and the plant.
Warning! All safety functions shall be tested before starting up the system.
Warning! Do not tamper or bypass the safety function. Failure can result in death
or serious injury.
Warning! The M12 connector shall be connected after Magne has been installed
on the intended surface.
Caution! Magne must be installed as close to the door handle as possible. The
distance between the lock and the handle creates a lever effect, reducing the holding
force.
Note! Do not connect Magne to power supply before Eva is within sensing
distance. The Adam sensor within Magne 4 needs to learn the Eva code. Make sure
that no power supply is connected when the cable is fitted to the Magne PIN out.
1.
Mount Magne and accessories, as close to the door handle as possible. See the
Installation guide, included in each JSM mounting kit.
Installation tolerances (in mm) for Magne 3 and JSM D23 on a sliding door:
1.
Magne
2.
Anchor plate
3.
Cellular rubber
4.
Sliding door
5.
Fence
2.
Make sure that Eva is correctly positioned in relation to the built-in Adam sensor
in Magne 4.
Note! It is very important that the units
are correctly positioned and that the safety
functions are tested. Magne 4’s safety
functionality is based on the Eden sensor.
3.
Mount the anchor plate with 2 × M8 screws with cellular rubber between the
anchor plate and the door. Do not compress the cellular rubber to a thickness less
than 8 mm. Recommended tightening torque is 7 ±2 Nm. Do not overtighten the
screws. This can deform the anchor plate, causing reduced or no holding force.
4.
Check that the surfaces of the magnet and the anchor plate are completely
parallel, so that full contact is obtained when the door is closed. If the anchor
plate tilts, the holding force of the lock can be significantly reduced or eliminated
entirely.
5.
Calibrate the position of the anchor plate with Magne. Maximum installation
tolerance between electromagnet and anchor plate is ±5 mm lengthways and ±3
mm sideways to Magne.
6.
Connect the pin out according to section Electrical connections. Make sure that
no power supply is connected when the cable is fitted to the Magne PIN out.
7.
After Magne has been installed on the intended surface, connect the M12
connector to Magne.
8.
Close the door to put Eva within sensing distance of Adam.
9.
Connect Magne to the power supply. Green LED and blue LED should now
illuminate (solid light).
Caution! After installation, check the looking function and check that the surfaces
of the magnet and the anchor plate are parallel.
Table of Contents
loading

Summary of Contents for ABB Magne 3 Series

  • Page 1 Magne 3 and 4 – Electromagnetic process lock The complete Product Manual can be found at: www.abb.com/jokabsafety [EN] General description Magne is an electromagnetic process lock that locks a door or hatch with a holding force of up to 1500 N.
  • Page 2: Maintenance

    Warning! In case of breakdown or damage to the product, remove and replace it European directives Machine Directive 2006/42/EC with a new unit. Contact the nearest ABB Jokab Safety Service Office or reseller. Do EMC directive 2014/30/EU not try to repair the product yourself. Never bypass the safety circuit.
  • Page 3 Die Einbaumaße (mm) für Magne und and JSM D23 an Schiebetüren entsprechen: Das komplette Produkthandbuch finden Sie unter www.abb.com/jokabsafety [DE] Allgemeine Beschreibung Magne ist eine elektromagnetische Prozesszuhaltung, die eine Tür oder eine Klappe mit einer Haltekraft von bis zu 1500 N zuhält.
  • Page 4: Led-Anzeige

    Magne kann die Zuhaltekraft senken oder gänzlich aufheben. Informationsausgang max. 20 mA Warnung! Wenden Sie sich bei einem Defekt oder bei Schäden am Produkt an ABB Kabelquerschnitte Bei einer Reihenschaltung mehrerer Geräte sind die Jokab Safety. Ersetzen Sie ein defektes Gerät durch ein Neugerät. Versuchen Sie Kabelquerschnitte zu beachten.
  • Page 5 è inserito nel PIN out di Magne. Il manuale completo del prodotto si trova nel sito: Montaggio e accessori di Magne. Vedere la guida per l’installazione in dotazione www.abb.com/jokabsafety ogni kit JSM. [IT] Misure d’installazione (mm) per Magne e JSM D23 su porte scorrevoli: Descrizione generale Magne è...
  • Page 6: Manutenzione

    Avvertenza! In caso di rottura o danno del prodotto contattare il l’ufficio di Normalmente 250 mA a 24 VDC, max 350 mA a 27,6 VDC assistenza ABB Jokab Safety più vicino a voi. Sostituire un’unità difettosa con una Uscita informazione max 20 mA nuova.
  • Page 7: Elektriska Anslutningar

    En defekt enhet ska bytas ut mot en ny enhet. Försök inte att reparera produkten på egen hand. Koppla aldrig förbi säkerhetskretsen. Varning! ABB Jokab Safety tar inte på sig något ansvar för funktionsfel på brytarna om installations- och underhållskraven inte implementerats.
  • Page 8: Tekniska Data

    Eva och Adam AWG (mm ) ampere Grön + röd Enheten är defekt Byt ut enheten. Kontakta ABB Jokab Safety 24 (0,20)2 Blinkar grönt - rött Giltig Eva-kod saknas Byt ut Eva. Om det fortfarande inte fungerar är 22 (0,32)3 snabbt enheten defekt och måste bytas ut.

This manual is also suitable for:

Magne 3xMagne 4x dynMagne 4 seriesMagne 4 dyn-infoMagne 4 ossd-infoMagne 4 dyn-2info

Table of Contents