Page 1 OWNER’S MANUAL Keep With Vehicle At All Times. Contains Important Information On Safety, Operation & Maintenance. 2008 Part No. 99011-80J21-03E June, 2007...
Page 3 INTRODUCTION Thank you for choosing SUZUKI and welcome to our growing family. Your choice was a wise one; SUZUKI products are a great value that will give you years of driving pleasure. This Owner’s Manual was prepared to help you have a safe, enjoyable, and trouble-free experience with your SUZUKI. In it you will learn about the vehicle’s operation, its safety features and maintenance requirements.
Page 4: Service Station
SERVICE STATION GUIDE 1. Fuel (see section 1) 2. Engine hood (see section 5) 3. Tire changing tools (see section 5) 4. Engine oil dipstick (see section 9) 5. Automatic transaxle fluid dipstick (see section 9) 6. Engine coolant (see section 9) 7.
Page 5: Table Of Contents
TABLE OF CONTENTS California Proposition 65 Warning WARNING Engine exhaust, some of its constitu- ents, and certain product compo- nents contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. FUEL RECOMMENDATION BEFORE DRIVING STEERING COLUMN CONTROLS...
Page 6: Location Of Warning Messages
Do not remove the messages for any reason. If a label comes off or the messages become difficult to be read, have it corrected by your SUZUKI dealer. 1. Air bag warning labels (on both sun visors) 2. Passenger seat belt warning label 3.
Page 7 In the event you require assistance related to your SUZUKI, while temporarily travel- ling in either the United States or Canada, you may wish to contact the Suzuki Cus- tomer Relations Department directly of the country in which you are temporarily oper- ating your vehicle.
Page 8: Warning
CB (Citizen’s Band) radios may cause electronic interfer- ence with your vehicle’s ignition sys- tem, resulting in vehicle performance problems. Consult your SUZUKI dealer or qualified service technician for advice on installing such mobile communication equipment.
Page 9 LEAK DETECTION PUMP NOTE: Your vehicle has a pump to regularly check the vehicle’s evaporative emission control system for leaks. This check is performed approximately five hours after the engine is turned off. During this leak check, you may hear a sound coming from the vehicle for several minutes.
Page 10 MEMO...
Page 11: Fuel Recommendation
FUEL RECOMMENDATION FUEL RECOMMENDATION Fuel Recommendation ... 1-1 65D394...
Page 12: Fuel Recommendation
5% methanol under any circumstances. Fuel system damage or vehicle performance problems resulting from the use of such fuels are not the responsibility of SUZUKI and may not be covered under the New Vehicle Limited Warranty. Fuel Pump Labeling...
Page 13: Before Driving
BEFORE DRIVING BEFORE DRIVING Keys ... 2-1 Door Locks ... 2-1 Windows ... 2-16 Mirrors ... 2-18 Seat Adjustment ... 2-19 Head Restraints ... 2-20 Seat Belts and Child Restraint Systems ... 2-22 Supplemental Restraint System (air bags) ... 2-40 60G404...
Page 14: Keys
BEFORE DRIVING Keys EXAMPLE 54G489 Your vehicle comes with a pair of identical keys. Keep the spare key in a safe place. One key can open all of the locks on the vehicle. The key identification number is stamped on a metal tag provided with the keys. Keep the tag in a safe place.
Page 15: Power Door Locking System
Power Door Locking System You can lock and unlock all the doors (including the tailgate of SX4) simulta- neously by: • Turning the key in a front door lock, or • Pushing the power door locking switch located on the driver’s side or the front passenger’s side door panel.
Page 16 BEFORE DRIVING Keyless Start System Remote Controller/Keyless Entry System Transmitter Type A Type B 66J111 Your vehicle is equipped with either a key- less start system remote controller (Type A) or a keyless entry system transmitter (Type B). The remote controller has a key- less entry system and a keyless start sys- tem.
Page 17 • You cannot lock the door unless all of the door are closed completely. • If you lose one of the remote controllers, ask your SUZUKI dealer as soon as pos- sible for a replacement. Be sure to have your dealer program the new remote controller code in your vehicle’s memory...
Page 18 BEFORE DRIVING When the remote controller is within the operating range described in this section, you can lock or unlock the doors by push- ing the request switch (1) on the door han- dle of the driver’s door, front passenger’s door or tailgate of SX4.
Page 19 • Be sure that the driver always carries the remote controller. • If you lose one of the remote controllers, ask your SUZUKI dealer as soon as pos- sible for a replacement. Be sure to have your dealer program the new remote controller code in your vehicle’s memory...
Page 20 BEFORE DRIVING Reminder function EXAMPLE If the remote controller is not in the vehicle under the following conditions, a buzzer sounds intermittently for about 2 seconds and the keyless start system indicator light on the instrument cluster blinks in red: •...
Page 21 BEFORE DRIVING should reprogram any additional remote controllers at the same time. • To purchase new remote controllers, see your SUZUKI dealer. • Before you begin programming, have all of your remote controllers available. To program a new remote controller 1) Close all the doors of the vehicle.
Page 22 If you still cannot operate the systems, see your SUZUKI dealer. To change the old remote controller codes in your vehicle’s memory If you have lost one of the remote control- lers, you should change the remote con- troller codes in your vehicle’s memory as...
Page 23 • If you lose one of the transmitters, ask your SUZUKI dealer as soon as possible for a replacement. Be sure to have your dealer program the new transmitter code in your vehicle’s memory so that the old...
Page 24 BEFORE DRIVING CAUTION The transmitter is a sensitive elec- tronic instrument. To avoid damaging the transmitter: • Do not expose it to impacts, mois- ture or high temperature such as by leaving it on the dashboard under direct sunlight. • Keep the transmitter away from magnetic objects such as a televi- sion.
Page 25 • If you try to program a fourth code, the oldest code will be cleared automatically. • To purchase new transmitters, see your SUZUKI dealer. • Before you begin programming, have all of your transmitters available. To program a new transmitter...
Page 26 BEFORE DRIVING To change the old transmitter codes in your vehicle’s memory If you have lost one of the transmitters, you should change the transmitter codes in your vehicle’s memory as soon as possible for security. To remove one of the transmitter codes from your vehicle’s memory, first replace all three of the transmitter codes in your vehi- cle’s memory, then program additional...
Page 27 If the tailgate can not be unlatched by pushing the unlatch switch (1), have the vehicle inspected by your SUZUKI dealer. WARNING • To avoid injury, do not use your fin- ger to push the emergency lever.
Page 28 BEFORE DRIVING Trunk Lid (SX4 SEDAN) EXAMPLE 55KS005 If your vehicle is equipped with a trunk lid key lock, you can open the trunk lid by using the key in the trunk lid lock. To open the trunk lid, insert the key and turn it clockwise to unlatch and lift the trunk lid.
Page 29: Windows
Internal Trunk Release (SX4 SEDAN) 54G297 There is a release lever located inside the trunk, on the rear part of the trunk lid. This lever is for emergency use so that if a per- son, such as a child, gets trapped in the trunk compartment, he can exit the vehicle.
Page 30 BEFORE DRIVING CLOSE OPEN 81A009 To open a window, push the top part of the switch and to close a window lift up the top part of the switch. The driver’s window has an auto-down fea- ture for added convenience (at toll booths or drive-through restaurants, for example).
Page 31: Mirrors
EXAMPLE 52LM012 NOTE: The rear door windows are not designed to open fully. They can be opened about 2/3 of the way down. NOTE: If you drive with one of the rear windows open, you may hear a loud sound caused by air vibration.
Page 32: Seat Adjustment
BEFORE DRIVING Outside Rearview Mirrors 79J033 Adjust the outside rearview mirrors so you can just see the side of your vehicle in the mirrors. The passenger’s side mirror is a convex (curved surface) mirror. Objects seen in this mirror will look smaller and appear far- ther away than when seen in a flat mirror.
Page 33: Head Restraints
Adjusting Seat Position Front seat 80J093 The adjustment lever for each front seat is located under the front of the seat. To adjust the seat position, pull up on the adjustment lever and slide the seat forward or rearward. After adjustment, try to move the seat forward and rearward to ensure that it is securely latched.
Page 34 BEFORE DRIVING Front EXAMPLE PUSH To raise the head restraint, pull upward on the restraint until it clicks. To lower the restraint, push down on the restraint while holding in the release knob (1). If a head restraint must be removed (for cleaning, replacement, etc.), use the following pro- cedure.
Page 35: Seat Belts And Child Restraint Systems
NOTE: It may be necessary to recline the seat- back to provide enough overhead clear- ance to remove the head restraint. Seat Belts and Child Restraint Systems 65D231 WARNING An air bag supplements, or adds to, the frontal crash protection offered by seat belts.
Page 36 BEFORE DRIVING Across the pelvis 65D201 WARNING (Continued) • Seat belts should never be worn with the straps twisted and should be adjusted as tightly as is com- fortable to provide the protection for which they have been designed. A slack belt will provide less pro- tection than one which is snug.
Page 37 WARNING (Continued) • Infants and small children should never be transported unless they are properly restrained. Restraint systems for infants and small chil- dren can be purchased commer- cially and should be used. Make sure that the system you purchase meets Federal Motor Vehicle Safety Standards.
Page 38 BEFORE DRIVING by pulling the shoulder portion of the belt upward through the latch plate. The length of the diagonal shoulder strap adjusts itself to allow freedom of movement. 2-25 All Seat Belts 60A036 To fasten the seat belt, sit up straight and well back in the seat, pull the latch plate attached to the seat belt across your body and press it into the buckle until you hear a...
Page 39: Seat Belt Reminder
60A039 To unfasten the belt, push the red “PRESS” button on the buckle and allow the belt to retract. Seat Belt Reminder Driver’s seat belt reminder light 80J020 Front passenger’s seat belt reminder light 80J021 BEFORE DRIVING When the driver and front passenger don’t buckle their seat belts, the driver’s seat belt reminder light in the instrument cluster and the front passenger’s seat belt reminder...
Page 40 BEFORE DRIVING Flow chart Ignition Switch “ON” Seat belt is unbuckled Reminder 1 30 sec. Vehicle speed: Vehicle speed: below 8 km/h over 8 km/h Vehicle speed: increase to 8 km/h Reminder 2 3 min. Reminder 3 No reminder Reminder 1 – 3 For each reminder 1 –...
Page 41: Shoulder Anchor Height Adjuster
Front passenger’s seat belt reminder The front passenger’s seat belt reminder will activate only when there is a passen- ger sitting in the front seat. In some situa- tions, however, such as when you place heavy objects in the front seat, the seat belt reminder can be activated as if there were a passenger present.
Page 42: Seat Belt Inspection
BEFORE DRIVING Seat Belt Inspection EXAMPLE 65D209S Periodically inspect the seat belts to make sure they work properly and are not dam- aged. Check the webbing, buckles, latch plates, retractors, anchorages and guide loops. Replace any seat belts which do not work properly or are damaged.
Page 43 EXAMPLE 80JC007 Booster seat EXAMPLE 80JC008 SUZUKI highly recommends that you use a child restraint system to restrain infants and small children. Many different types of child restraint systems are available; make sure that the restraint system you select meets Federal Motor Vehicle Safety Stan- dards.
Page 44 BEFORE DRIVING 65D608 65D609 2-31 WARNING Children could be endangered in a crash if their child restraints are not properly secured in the vehicle. When installing a child restraint sys- tem, be sure to follow the instruc- tions below. Be sure to secure the child in the restraint system accord- ing to the manufacturer’s instruc- tions.
Page 45 EXAMPLE 83E035 1) Pull all of the remaining webbing out of the retractor. You will hear a click, which means that the emergency locking retractor (ELR) has converted to func- tion as an automatic locking retractor (ALR). EXAMPLE 83E032 2) Allow the extra webbing to retract, and pull the webbing toward the retractor to take up any slack.
Page 46 BEFORE DRIVING WARNING Before installing a child restraint in the rear center seat, follow these steps for secure installation: • Make sure the detachable connec- tor is securely latched and the web- bing is not twisted. • Make sure the seat belt is passed through the seat belt guide.
Page 47: Installation With The Latch System
Installation with the LATCH System Rigid lower connecting Flexible lower connecting bar type strap type 65D337 EXAMPLE 79J058 Your vehicle is equipped with lower anchors for securing up to one or two stan- dard LATCH-type child restraint(s) in the second row seats. (LATCH stands for Lower Anchors and Tethers for Children.) The anchors are located where the rear of the seat cushion meets the bottom of the...
Page 48 BEFORE DRIVING EXAMPLE 65D340 3) Snap the strap hooks to the anchors. Take care not to pinch your fingers. EXAMPLE 65D341 4) Return the seatback to the normal, upright position. Tighten the lower straps as described in the child restraint 2-35 owner’s manual.
Page 49 EXAMPLE 54G183 3) Use your hands to carefully align the connecting bar tips with the anchors. Take care not to pinch your fingers. EXAMPLE 54G184 4) Push the child restraint toward the anchors so that the connecting bar tips are partially hooked to the anchors. Use your hands to confirm the position.
Page 50 BEFORE DRIVING Installation of Child Restraint with Top Strap EXAMPLE 63J021 SX4 SEDAN EXAMPLE 56KN015 2-37 Some child restraint systems require the use of a top strap. Top strap anchor brack- ets are provided in your vehicle at the loca- tions shown in the illustrations.
Page 51: Seat Belt Extender
(3) Open end of extender buckle If a seat belt cannot be fastened securely because it is not long enough, see your authorized SUZUKI dealer for a seat belt extender. Seat belt extenders are available for each seating position except for the rear center position.
Page 52 2-39 Seat Belt Pretensioner System (for front seat belt only) WARNING This section of the owner’s manual describes your SUZUKI’s SEAT BELT PRETENSIONER SYSTEM. read and follow ALL these instruc- tions carefully to minimize your risk of severe injury or death.
Page 53: Supplemental Restraint System (Air Bags)
“LOCK” position for at least 90 seconds before performing any electri- cal service work on your SUZUKI. Do not touch pretensioner system components or wiring. The wires are wrapped with yellow tape or yellow tubing, and the couplers are yellow.
Page 54 BEFORE DRIVING EXAMPLE 2-41 Your vehicle is equipped with a Supple- mental Restraint System consisting of the following components in addition to a lap- shoulder belt at each front seating position. 1. Driver’s front air bag 2. Front passenger’s front air bag 3.
Page 55: Front Air Bags
AIR BAG light stays on, or comes on while driving, the air bag system (or the seat belt pretensioner system) may not work prop- erly. Have the air bag system inspected by an authorized SUZUKI dealer as soon as possible. Front Air Bags EXAMPLE...
Page 56 BEFORE DRIVING Front air bags will not inflate 65D236 Front air bags will probably not inflate 65D237 2-43 They are not designed to inflate in rear impacts, side impacts, rollovers or minor frontal collisions, since they would offer no protection in those types of accidents. Remember, since air bags deploy only one time during an accident, seat belts are needed to restrain occupants from further...
Page 57 Side air bags are located in the part of the front seatbacks closest to the doors. The words “SRS AIRBAG” are molded into the side air bag cover to identify the location of the side air bags. Side curtain air bags are located in the roof lining.
Page 58 If this happens, deploy- ment of the driver’s front air bag will not include consideration of seat fore/aft posi- tion. Have the air bag system inspected by an authorized SUZUKI dealer as soon as possible. Front Passenger’s Seat Belt Buckle Sensor The front passenger’s seat belt buckle is...
Page 59: Front Passenger Sensing System
Front Passenger Sensing System The front passenger sensing system will turn off the front passenger’s front air bag and seat belt pretensioner under certain conditions. This system works using a sen- sor mat that is part of the front passenger’s seat.
Page 60 Have the system inspected by an authorized SUZUKI dealer as soon as possible.
Page 61 WARNING • Do not spill any liquids on the seat. Liquids can damage the sensors under the front seat. • Have the driver’s seat position sen- sor and the front passenger’s sen- sor mat inspected by your dealer after a collision. •...
Page 62 SUZUKI dealer to ensure it is in proper working order. Your vehicle is equipped with a diagnostic module which records information about the air bag system if the air bags deploy in a crash.
Page 63 “LOCK” position for at least 90 seconds before performing any electrical service work on your SUZUKI. Do not touch air bag system components or wires. The wires are wrapped with yellow tape or yellow tubing, and the couplers are yellow for easy identification.
Page 64 BEFORE DRIVING MEMO 2-51...
Page 65: Steering Column Controls
STEERING COLUMN CONTROLS STEERING COLUMN CONTROLS Ignition Switch ... 3-1 Lighting/Turn Signal Control Lever ... 3-5 Windshield Wiper and Washer Lever ... 3-6 Rear Window Wiper/Washer Switch (if equipped) ... 3-8 Tilt Steering Lock Lever (if equipped) ... 3-8 Cruise Control (if equipped) ... 3-9 Remote Audio Controls (if equipped) ...
Page 66: Ignition Switch
STEERING COLUMN CONTROLS 65D611 WARNING To avoid possible injury, do not oper- ate controls by reaching through the steering wheel. Ignition Switch 60B041 The ignition switch has the following four positions: LOCK This is the normal parking position. It is the only position in which the key can be removed.
Page 67 60A300S Accessories such as the radio can oper- ate, but the engine is off. This is the normal operating position. All electrical systems are on. START This is the position for starting the engine using the starter motor. The key should be released from this position as soon as the engine starts.
Page 68 STEERING COLUMN CONTROLS • If the keyless start system red indicator light illuminates, the remote controller may not be in the vehicle or the battery of the remote controller may be unreli- able. NOTE: • If the battery of the remote controller runs down or there are strong radio waves or noise, the operating range may be narrower or the remote controller may...
Page 69 SUZUKI dealer. • Do not leave the ignition switch in the “ON” position if the engine is not running or the battery will dis- charge.
Page 70: Lighting/Turn Signal Control Lever
STEERING COLUMN CONTROLS Lighting/Turn Signal Control Lever Lighting Operation EXAMPLE 80JC031 To turn the lights on or off, twist the knob on the end of the lever. There are three positions: in the “OFF” position all lights are off; in the middle position the front parking lights, taillights, license plate light, and instrument lights are on, but the head- lights are off;...
Page 71: Windshield Wiper And Washer Lever
Turn Signal Operation With the ignition switch in the “ON” posi- tion, move the lever up or down to activate the right or left turn signals. Normal turn signal EXAMPLE 80JC033 Move the lever all the way upward or down- ward to signal.
Page 72: Windshield Washer
STEERING COLUMN CONTROLS EXAMPLE 80JC036 If the lever is equipped with the “INT TIME” control, turn the control forward or rear- ward to adjust the intermittent wiper opera- tion to the desired interval. Windshield Washer EXAMPLE 80JC037 To spray windshield washer fluid, pull the lever toward you.
Page 73: Rear Window Wiper/Washer Switch (If Equipped)
Rear Window Wiper/Washer Switch (if equipped) EXAMPLE Washer Wiper Intermittent wiper 80JC038 To turn the rear wiper on, twist the rear wiper switch on the end of the lever for- ward to the “ON” position. If your vehicle is equipped the “INT” position, the rear wiper operates intermittently when you twist the switch forward to the “INT”...
Page 74: Cruise Control (If Equipped)
STEERING COLUMN CONTROLS WARNING Never attempt to adjust the steering wheel height while the vehicle is moving or you could lose control of the vehicle. Cruise Control (if equipped) 80J025 The cruise control system allows you to maintain a steady speed without keeping your foot on the accelerator pedal.
Page 75 80J026 To Set Cruising Speed Turn on the cruise control system by push- ing the “ON/OFF” switch (1). Accelerate to the desired speed and push the “SET/ COAST” switch (3). Take your foot off the accelerator pedal and the set speed will be maintained.
Page 76: Remote Audio Controls (If Equipped)
STEERING COLUMN CONTROLS Remote Audio Controls (if equipped) 80J027 You can control basic functions of the audio system with the switches on the steering wheel. For details, refer to “Audio Systems” in the “INSTRUMENT PANEL” section. 3-11 Horn EXAMPLE 80J028 Press the horn pad on the steering wheel to sound the horn.
Page 77: Instrument Panel
INSTRUMENT PANEL INSTRUMENT PANEL Instrument Panel ... 4-1 Instrument Cluster ... 4-2 Warning and Indicator Lights ... 4-3 A/T Selector Position Indicator (if equipped) ... 4-10 Speedometer/Odometer/Trip meter ... 4-11 Tachometer ... 4-12 Fuel Gauge ... 4-12 Temperature Gauge ... 4-13 Hazard Warning Switch ...
Page 78: Instrument Panel
INSTRUMENT PANEL Instrument Panel 1. Instrument cluster 2. Ignition switch 3. Lighting switch/Turn signal and dim- mer switch 4. Windshield wiper and washer switch/ Rear window wiper and washer switch (if equipped) 5. Hazard warning switch 6. Other switches (if equipped) 7.
Page 79: Instrument Cluster
INSTRUMENT PANEL Instrument Cluster 1. Speedometer 2. Odometer/Trip meter 3. Odometer/Trip meter selector knob 4. Tachometer 5. Fuel gauge 6. Temperature gauge 7. Warning and indicator lights EXAMPLE 80JC011...
Page 80: Warning And Indicator Lights
Have your vehicle inspected by an autho- rized SUZUKI dealer. Even if the light turns off after blinking, indicating that monitoring system has recov- ered, make sure to have an autho-...
Page 81 WARNING If any of the following conditions occur, you should immediately ask your SUZUKI dealer to inspect the brake system. • If the brake system warning light does not go out after the parking brake has been fully released.
Page 82: Anti-Lock Brake System (Abs) Warning Light
ABS. If one of these happens, have the system inspected by your SUZUKI dealer. If the ABS becomes inoperative, the brake sys- tem will function as an ordinary brake sys- tem that has no ABS.
Page 83: Oil Pressure Light
Check the oil level and add oil if necessary. If there is enough oil, the lubrication system should be inspected by your SUZUKI dealer before you drive the vehicle again. CAUTION • If you operate the engine with this light on, severe engine damage can result.
Page 84: Malfunction Indicator Light
If the malfunction indicator light comes on or blinks when the engine is running, ser- vice to the emission control system is nec- essary. Bring the vehicle to your SUZUKI dealer to have the emission control system serviced right away and avoid hard accel- eration until the service is performed.
Page 85: Electric Power Steering Light
If this light comes on while driving, the power steering system may not work prop- erly. Have the system inspected by your SUZUKI dealer. NOTE: If the power steering system does not work properly, you will feel heavier to steer but you still will be able to steer.
Page 86: Turn Signal Indicators
Have the system inspected authorized SUZUKI dealer. If the oil temperature of the parts for i-AWD system is high, this light will blink. The “i- AWD AUTO” or “i-AWD LOCK” mode will be changed to the “2WD” mode automati- cally to prevent a damage of the parts for i- AWD system.
Page 87: A/T Selector Position Indicator (If Equipped)
NOTE: • When the vehicle speed is increased, the “i-AWD LOCK” mode will be changed to the “i-AWD AUTO” mode automati- cally. The “i-AWD AUTO” indicator light will come on and stay on. • When the ignition switch is turned to the “OFF”...
Page 88: Speedometer/Odometer/Trip Meter
INSTRUMENT PANEL Speedometer/Odometer/Trip meter EXAMPLE (1) Speedometer (2) Odometer/Trip meter (3) Indication selector knob Speedometer The speedometer indicates vehicle speed in MPH. Odometer/Trip meter When the ignition switch is turned to “ON”, the display shows the odometer or trip meter. The odometer records the total dis- tance the vehicle has been driven.
Page 89: Tachometer
Tachometer EXAMPLE The tachometer indicates engine speed in revolutions per minute. CAUTION Never drive with the engine speed indicator in the red zone or severe engine damage can result. Fuel Gauge 80J033 When the ignition switch is in the “ON” position, this gauge gives an approximate indication of the amount of fuel in the fuel tank.
Page 90: Temperature Gauge
INSTRUMENT PANEL Temperature Gauge 79J133 When the ignition switch is in the “ON” position, this gauge indicates the engine coolant temperature. Under normal driving conditions, the indicator should stay within the normal, acceptable temperature range between “H” and “C”. If the indicator approaches “H”, overheating is indicated.
Page 91: Instrument Light Brightness Control
® For details of the ESP systems, refer to ® “Electronic Stability Program (ESP the “OPERATING YOUR VEHICLE” sec- tion. Instrument Light Brightness )” in Control Your vehicle has a system to automatically dim the instrument panel lights when the ignition switch is in the “ON”...
Page 92: Heated Rear Window And Heated Outside Rearview Mirrors (If Equipped) Switch
INSTRUMENT PANEL Heated Rear Window and Heated Outside Rearview Mirrors (if equipped) Switch Type 1 79J043 Type 2 79J119 4-15 When the rear window is misted, push this switch (1) to clear the window. 80JC040 If the driver’s outside rearview mirror has the mark (2), it is also equipped with the heated outside rearview mirrors.
Page 93: Fog Light Switch (If Equipped)
Fog Light Switch (if equipped) 64J058 The front fog light comes on when the fog light switch is pushed in with the lighting switch turned to the third position and the beams set to the low beam position. Cigarette Lighter and Ashtray (if equipped) Cigarette Lighter (if equipped) 80JC041...
Page 94: Information Display
INSTRUMENT PANEL Information Display EXAMPLE (1) Clock (2) Thermometer (3) Instantaneous fuel consumption/Aver- age fuel consumption/Driving range (4) “H” button (5) “M” button (6) “DISP” button (7) Freezing mark (8) “SET” button 4-17 Clock (1) The clock is shown when the ignition switch is in the “ACC”...
Page 95 80J079 Every time you push the “DISP” button (6), the display will be changed among the fol- lowing four displays. (a) Instantaneous fuel consumption (b) Average fuel consumption (c) Driving range (d) No display Instantaneous fuel consumption (a) If you selected instantaneous fuel con- sumption the last time you drove the vehi- cle, the display indicates “--.-”...
Page 96 INSTRUMENT PANEL Unit indication of fuel consumption and driving range You can change the unit indication of fuel consumption when selecting instanta- neous fuel consumption or average fuel consumption in the display. You can also change the unit indication of driving range when selecting driving range in the display.
Page 97: Glove Box
For details about the seat belt reminder, refer to “Seat Belts and Child Restraint Systems” in the “BEFORE DRIVING” sec- tion. WARNING It is absolutely essential that the driver and passengers wear their seat belts at all times. Persons who are not wearing seat belts have a much greater risk of injury if an accident occurs.
Page 98: Heating And Air Conditioning System
INSTRUMENT PANEL Heating and Air Conditioning System There are three types of heating and air conditioning systems as follows: • Heating System • Manual Heating and Air Conditioning System • Automatic Heating and Air Conditioning System (Climate Control) 4-21 Air Outlet EXAMPLE 1.
Page 99: Heating System
Side outlet When “Open”, air comes out regardless of the air flow selector position. Heating System Description of Controls Temperature selector (1) This is used to select the temperature by turning the selector. Blower speed selector (2) This is used to turn on the blower and to select blower speed by turning the selec- tor.
Page 100 INSTRUMENT PANEL Bi-level (b) 79J066 Temperature-controlled air comes out of the floor outlets and cooler air comes out of the center and side outlets. When the temperature selector (1) is in the fully COLD position or fully HOT position, how- ever, the air from the floor outlets and the air from the center and side outlets will be the same temperature.
Page 101 System Operating Instructions Natural ventilation Select “VENTILATION” and “FRESH AIR”, the temperature selector to the desired temperature position, and the blower speed selector to “OFF”. Fresh air will flow through the vehicle during driving. Forced ventilation The control settings are the same as for natural ventilation except you set the blower speed selector to a position other than “OFF”.
Page 102: Conditioning System
INSTRUMENT PANEL Manual Heating and Air Conditioning System Description of Controls 80JC042 Temperature selector (1) This is used to select the temperature by turning the selector. Blower speed selector (2) This is used to turn on the blower and to select blower speed by turning the selec- tor.
Page 103 Heat & defrost (d) 79J068 Temperature-controlled air comes out of the floor outlets, the windshield defroster outlets, the side defroster outlets and the side outlets. Defrost (e) 79J069 Temperature-controlled air comes out of the windshield defroster outlets, the side defroster outlets and the side outlets. NOTE: When the air flow selector (3) is turned either to “Heat &...
Page 104 INSTRUMENT PANEL System Operating Instructions Natural ventilation Select “VENTILATION” and “FRESH AIR”, the temperature selector to the desired temperature position, and the blower speed selector to “OFF”. Fresh air will flow through the vehicle during driving. Forced ventilation The control settings are the same as for natural ventilation except you set the blower speed selector to a position other than “OFF”.
Page 105: Climate Control
Clean or replace them as specified in “Maintenance Schedule” “INSPECTION AND MAINTENANCE” sec- tion. Have this job done by your SUZUKI dealer as the lower glove box must be low- ered for this job. NOTE: Your vehicle uses the air conditioning refrigerant HFC-134a, commonly called “R-134a”.
Page 106 If the A/C indicator light (4) blinks, there is a problem in the heating system and/or air conditioning system. You should have the system inspected authorized SUZUKI dealer. 4-29 Blower speed selector/Air intake selec- tor (2) 79J096 This is used to turn on the blower and to select blower speed.
Page 107 Air flow selector (3) 79J097 AUTO (h) Temperature-controlled air comes out of various outlets automatically. Ventilation (c) 79J065 Temperature-controlled air comes out of the center and side air outlets. Bi-level (d) 79J066 Temperature-controlled air comes out of the floor outlets and cooler air comes out of the center and side outlets.
Page 108 INSTRUMENT PANEL System Operating Instructions Automatic operation EXAMPLE 80J097 You can let the climate control system work automatically. To set the system in fully- automatic operation, follow the procedure below. 1) Set the desired temperature by turning the temperature selector (1). 2) Turn the blower speed selector (2) to the “AUTO”...
Page 109: Audio Systems
79J070 NOTE: If you need maximum defrosting: • set the air flow selector to “DEFROST” (the air conditioning system will come on and the “FRESH AIR” mode will be selected automatically), • set the blower speed selector to HIGH, • adjust the temperature selector to the HOT end, and •...
Page 110 Even in the event that trouble arises, never open the case, disassemble the unit, or lubricate the rotating parts. Please bring the unit to an authorized SUZUKI dealer or a Clarion service Department. Cautions on Handling 52D274 This unit has been designed specifically for playback of compact discs bearing the mark (A).
Page 111 Never touch the surface. 52D347 To remove fingermarks and dust, use a soft cloth, and wipe in a straight line from the center of the compact disc to the cir- cumference. 52D277 New discs may have some roughness around the edges. The unit may not work or the sound may skip if such discs are used.
Page 112: Basic Operations
INSTRUMENT PANEL Basic Operations Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL 4-35 (3) (4) (3) (4) 80J061 (1) Power on/off knob Volume control knob (2) Tone/balance/fader control knob (3) Preset button 5 (4) Preset button 6...
Page 113 Turning power on/off Press the power on/off knob (1). The unit starts in the function mode it was in when the power was turned off last. Adjusting the volume Turn the volume control knob (1). Turning it clockwise increases the volume; turning it counterclockwise decreases the volume.
Page 114 INSTRUMENT PANEL Listening to the Radio Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL 4-37 Display (1) Band switch button (FM/AM) (2) Seek up button (3) Seek down button (4) Manual tuning knob (5) Preset buttons (1 to 6) (6) Auto store button (AS)/ Scan button (SCAN)
Page 115 Selecting the reception band Press the band switch button (1). Each time the button is pressed, the recep- tion band is switched as follows: 66J098 Seek tuning Press the seek up button (2) or the seek down button (3). The unit stops searching for a station at a frequency where a broadcast station is available.
Page 116: Listening To A Cd
INSTRUMENT PANEL CAUTION avoid damage radio antenna: • Remove the antenna before using an automatic car wash. • Remove the antenna when it is pos- sible for the antenna to hit some- thing such as a low ceiling in a parking garage or putting a car cover over your car.
Page 117 Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (Built in CD Player) INSTRUMENT PANEL Display (1) CD insertion slot (2) CD eject button (3) Disc button (CD/AUX) (4) Track up button/Fast forward button (5) Track down button/Rewind button (6) Repeat button (RPT) (A) Mode indicator (B) Track number (C) Play time...
Page 118 INSTRUMENT PANEL NOTE: About Single CDs (8 cm CDs) • No adapter is required to play a single • A single CD is inserted from the center of the CD insertion slot. • Since an ejected single CD is not auto- matically reloaded, be sure to remove the ejected single CD.
Page 119 Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL (Built-in CD Changer) INSTRUMENT PANEL Display (1) Load button (LOAD) (2) Disc select buttons (1 to 6) (3) CD insertion slot (4) CD eject button (5) Disc button (CD/AUX) (6) Track up button/Fast forward button (7) Track down button/Rewind button (8) Repeat button (RPT) (A) Mode indicator...
Page 120 INSTRUMENT PANEL NOTE: About Single CDs (8 cm CDs) • Since the unit is not compatible with a single CD, do not load it into the unit. • Keep in mind the fact that a single CD cannot be played even using a single CD adaptor for the unit.
Page 121 Ejecting all the CDs Press the CD eject button (4) for 2 seconds or longer. All the CDs will be ejected from the unit in a sequential manner. • Please prepare location where removed CDs can be stored. • If you leave the ejected CD without removing it, it will be drawn into the unit automatically after about 15 seconds.
Page 122 INSTRUMENT PANEL Listening to an MP3/WMA Disc Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL 4-45 Display (Type 1) Display (Type 2) (1) Sound control knob (2) Repeat button (RPT) (3) Track up button/Fast forward button (4) Track down button/Rewind button (5) Display button (DISP)
Page 123 MP3/WMA MODE Selecting a folder Turn the sound control knob (1) to select a folder. Repeat play Press the repeat button (2). Each time the button is pressed, repeat play mode changes as follows: Type 1 TRACK REPEAT FOLDER REPEAT 66J128 Type 2 TRACK REPEAT...
Page 124 (A) Band (B) Channel number (C) Category indicator If you want to purchase XM Satellite Radio Service, contact your SUZUKI dealer. It is necessary to buy a special tuner to receive XM broadcasting. Your vehicle is capable of receiving XM...
Page 125 XM MODE Selecting a band Press the XM button (1). Each time the button is pressed, the band changes in the following order. 66J129 Selecting a category Press the seek up button (3) or the seek down button (4). The category is changed. Turning the category function on/off Press and hold the category button (2) for 2 seconds or longer, and “CATEGORY...
Page 126: Listening To Audio For Aux (Option)
INSTRUMENT PANEL Listening to Audio for AUX (Option) Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL 4-49 Display (1) Aux button (CD/AUX) (A) Mode indicator Aux function This system has an external input terminal so you can listen to audio from an external device connected to this unit.
Page 127 Listening to a CD from an External CD Changer (Option) Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL INSTRUMENT PANEL Display (A) (B) (1) Disc button (CD/AUX) (2) Disc select buttons (1 to 6) (3) Track up button/Fast forward button (4) Track down button/Rewind button (5) Repeat button (RPT)
Page 128 INSTRUMENT PANEL Selecting a CD changer mode Press the disc button (1). Each time the button is pressed, the selected CD plays as follows: Built-in CD player CD changer 1 CD changer 2 52D300 • When only one CD changer is con- nected to this unit, CD changer 2 is skipped.
Page 129 Repeat play Press the repeat button (5). Each time the button is pressed, repeat play mode changes as follows: TRACK REPEAT DISC REPEAT 66J144 NOTE: This operation should be performed within 2 seconds. To cancel repeat play, press the repeat but- ton (5) several times to change the repeat play mode to OFF.
Page 130 INSTRUMENT PANEL Remote Audio Controls (if equipped) 80J103 You can control basic functions of the audio system with the switches on the steering wheel. 4-53 To control the volume: • To increase the volume, push the upper part of the switch (1). The volume contin- ues to increase until you release the switch.
Page 131 Anti-Theft Feature Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL INSTRUMENT PANEL (1) Power on/off knob (2) Track up button/Fast forward button (3) Preset buttons (1 to 6) The anti-theft feature is intended to dis- courage theft or the audio system by pre- venting the system from operating when it is moved to a different vehicle.
Page 132 INSTRUMENT PANEL Setting the Anti-Theft Function 1) Turn off the power by pressing the power on/off knob (1). 66J118 2) Press the power on/off knob (1) while pressing and holding the track up but- ton (2). The “ENTRY 0000” will blink and the audio system enter PIN-input mode.
Page 133 EXAMPLE 66J124 3) Input your PIN. The power of the audio system will turn off and your PIN will be deleted. To change your PIN, first delete your current PIN, then set a new one. Confirming Your Personal Identifi- cation Number (PIN) When the main power source is discon- nected such as when you exchange your battery, etc, you will have to confirm your...
Page 134: Troubleshooting
Water droplets may form on the internal lens is turned on. when the car is parked in a humid place. 4-57 Cause Contact your authorized SUZUKI dealer. Contact your authorized SUZUKI dealer. Cause Tune correctly to the station frequency. Select stations by manual tuning.
Page 135 If a problem should occur, the display shows the type of error. Refer to the table below and take proper measures to correct the problem. If the problem is corrected, the unit will operate normally. Error display If an error display not listed above appears, turn off the unit and contact your SUZUKI dealer. Measures to be taken CD/CD changer “Mechanical error”.
Page 136 INSTRUMENT PANEL MEMO 4-59...
Page 137: Other Controls And Equipment
OTHER CONTROLS AND EQUIPMENT OTHER CONTROLS AND EQUIPMENT Parking Brake Lever ... 5-1 Pedals ... 5-1 Gearshift Lever ... 5-2 Fuel Filler Cap ... 5-3 Folding Rear Seats (SX4) ... 5-4 Sun Visor ... 5-8 Interior Light Switch ... 5-8 Spot Light ...
Page 138: Parking Brake Lever
• If the parking brake does not hold the vehicle securely or does not fully release, have your vehicle inspected immediately by an autho- rized SUZUKI dealer. WARNING Always set the parking brake fully before leaving your vehicle or it may roll, causing injury or damage.
Page 139: Gearshift Lever
It could result in excessive clutch wear or clutch dam- age. Brake Pedal (2) Your SUZUKI vehicle is equipped with either front and rear disc brakes or front disc brakes and rear drum brakes. Depressing the brake pedal applies both sets of brakes.
Page 140: Fuel Filler Cap
OTHER CONTROLS AND EQUIPMENT Your vehicle is equipped with either a man- ual transaxle or automatic transaxle. The gearshift lever for each transaxle type is shown. For details on how to use the tran- saxle, refer to the “Using the Transaxle” in “OPERATING YOUR VEHICLE”...
Page 141: Folding Rear Seats (Sx4)
WARNING If you need to replace the fuel cap, use a genuine SUZUKI cap. Use of an improper cap can result in a malfunc- tion of the fuel system or emission control system. It may also result in fuel leakage in the event of an acci- dent.
Page 142 OTHER CONTROLS AND EQUIPMENT 79J213 2) Stow the seat belt buckles of the center and right seating position as shown in the illustration. CAUTION When you fold the rear seatback for- ward, stow the seat belt buckles of the center and right seating position into the seat first.
Page 143 80J043 7) Push down the adjuster (2) to make the strap slack, and then unhook the strap by pushing down the hook (3). 80J044 8) Hook the strap (4) to the front seat head restraint as shown in the illustration. CAUTION When securing the folded rear seat with a strap, adjust the strap length...
Page 144 OTHER CONTROLS AND EQUIPMENT 79J129 2) Pull down the seat cushion until it locks into place. WARNING When returning the rear seat cushion to the normal position, be careful that your finger is not caught between the lock and the floor. CAUTION •...
Page 145: Sun Visor
After returning the seat, try moving the seat and seatback to make sure they are securely latched. LOCK UNLOCK 79J127 CAUTION After securing the rear seatback, make sure that it is locked securely. If it is not, you will see red in the release lever.
Page 146: Spot Light
OTHER CONTROLS AND EQUIPMENT EXAMPLE 79J075 NOTE: The number of doors involved in the light- ing operation of the interior light depends on the vehicle specification. If there is a switch (rubber projection) at the door opening as shown, the door is involved in the lighting operation.
Page 147: Eyeglasses Holder (If Equipped)
Eyeglasses Holder (if equipped) 86G067 To use the eyeglasses holder, open the cover. Do not put heavy or sharp items in the box. CAUTION If you park your vehicle outdoors in direct sunlight or in hot weather, the eyeglasses holder can get very hot since it is close to the roof.
Page 148: Cup Holder And Storage Area (If Equipped)
OTHER CONTROLS AND EQUIPMENT Cup Holder and Storage Area (if equipped) EXAMPLE 80J046 EXAMPLE 79J052 Cup holders are provided in the center console. 5-11 WARNING Do not use the cup holder or the stor- age bin to hold cups containing hot liquids or sharp-edged, hard or breakable objects.
Page 149: Frame Hooks
Frame Hooks Front (1) EXAMPLE 80JC048 SX4 SEDAN Front (1) EXAMPLE 80JC049 Rear (2) EXAMPLE 80JC061 SX4 SEDAN Rear (2) EXAMPLE 56KN033 OTHER CONTROLS AND EQUIPMENT Side (3) EXAMPLE EXAMPLE 80JC062 79J132 5-12...
Page 150: Tire Changing Tool
OTHER CONTROLS AND EQUIPMENT Frame hooks are provided on the front (1), rear (2) and side (3) of the vehicle. The hooks (1) and (2) are used for emergency situations. The hooks (3) are used for trailer/train shipping purposes. To tow your vehicle on the road or highway, follow the instruction of “Towing”...
Page 151: Luggage Compartment Cover (If Equipped)
79J086 SX4 SEDAN 80JC015 To stow the jack, place it in the storage bracket and turn the shaft clockwise until the jack is securely held in place. WARNING The jack should be used only to change wheels. It is important to read jacking instructions “EMERGENCY SERVICE”...
Page 152: Luggage Compartment Light (Sx4)
OTHER CONTROLS AND EQUIPMENT Luggage or other cargo placed in the lug- gage compartment can be hidden from view by a luggage compartment cover. WARNING Do not carry items on top of the lug- gage compartment cover, even if they are small and light.
Page 153: Radio Antenna
Radio Antenna EXAMPLE 63J055 The radio antenna at the end of the roof is removable. If the antenna hits anything such as when parking in a garage with a low ceiling, remove the antenna. Turn the antenna counterclockwise. To reinstall the antenna, turn it clockwise firmly by hand.
Page 154 You can use the roof rails or the roof rack anchors to attach the optional roof rack which is available at your SUZUKI dealer. If you use a roof rack, observe the instruc- tions and precautions in this section and provided with the roof rack.
Page 155: Operating Your Vehicle
OPERATING YOUR VEHICLE OPERATING YOUR VEHICLE Exhaust Gas Warning ... 6-1 Daily Inspection Checklist ... 6-1 Starting the Engine ... 6-2 Engine Block Heater (if equipped) ... 6-4 Using the Transaxle ... 6-5 Using the 2WD/i-AWD (intelligent All Wheel Drive) Switch (if equipped) ...
Page 156: Exhaust Gas Warning
OPERATING YOUR VEHICLE Exhaust Gas Warning 52D334 WARNING Avoid breathing exhaust gases. Exhaust gases contain carbon mon- oxide, a potentially lethal gas that is colorless and odorless. Since carbon monoxide is difficult to detect by itself, be sure to take the following precautions to help prevent carbon monoxide from entering your vehicle.
Page 157: Starting The Engine
This should clear the engine if it is flooded. If you are unable to start the engine using this procedure, consult your SUZUKI dealer. Starting a Warm Engine Use the same procedure as for “Starting a...
Page 158 OPERATING YOUR VEHICLE Vehicle With Keyless Start System 80JC002 The ignition switch can be operated with- out using an ignition key when the remote controller is in an area of the vehicle other than the rear luggage area. To turn the ignition switch, first push in the switch.
Page 159: Engine Block Heater (If Equipped)
Engine Block Heater (if equipped) EXAMPLE 54G209 The engine block heater will help you start the engine more easily in very cold weather (–18°C (0°F) or below). To use the engine block heater: 1) Turn off the engine. 2) Open the engine hood. 3) Untie the block heater cord and remove the block heater plug cap.
Page 160: Using The Transaxle
OPERATING YOUR VEHICLE Using the Transaxle 4-Speed Automatic Transaxle 77J021 Gearshift lever 77J028 WARNING Always depress the brake pedal before shifting from “P” (Park) (or “N” (Neutral) if the vehicle is station- ary) to a forward or reverse gear, to help prevent the vehicle from moving unexpectedly when you shift.
Page 161: Manual Transaxle
L (Low 1) Use this position to provide maximum power when climbing steep hills or driving through deep snow or mud, or to provide maximum engine braking when going down steep hills. NOTE: If you move the gearshift lever to a lower gear while driving faster than the maximum allowable speed for the lower gear, the transaxle will not actually downshift until...
Page 162: Using The 2Wd/I-Awd (Intelligent All Wheel Drive) Switch (If Equipped)
OPERATING YOUR VEHICLE Using the 2WD/i-AWD (intelligent All Wheel Drive) Switch (if equipped) 80J009 This i-AWD system enables you to select the driving mode according to the driving conditions by operating the 2WD/i-AWD switch. With this feature, you can select 3 mode positions, “2WD”, “i-AWD AUTO”...
Page 163 • If the “i-AWD AUTO” and the “i- AWD LOCK” indicator lights stay on and come on simultaneously when driving, there may be some- thing wrong the i-AWD system. Have the system inspected by an authorized SUZUKI dealer.
Page 164: Braking
OPERATING YOUR VEHICLE CAUTION Unevenly worn tires can cause prob- lems in the operation of the 2WD/i- AWD switch. Be sure to rotate the tires according to the maintenance schedule. Refer to “Tires” and “Main- tenance Schedule” in the “INSPEC- TION AND MAINTENANCE”...
Page 165: Brake Assist System
WARNING Even without reserve power in the brake system, you can still stop the vehicle by pressing the brake pedal harder than normally required. How- ever, the stopping distance may be longer. Brake Assist System When you slam the brakes on, the brake assist system judges as an emergency stop and provides more powerful braking for a driver who cannot hold down the...
Page 166 If both warning lights come on, drive carefully, avoid- ing hard braking as much as possi- ble, and ask your SUZUKI dealer to inspect the ABS system immediately. How the ABS Works A computer continuously monitors wheel speed.
Page 167: Electronic Stability Program (Esp®) (If Equipped)
Electronic Stability Program ® (ESP ) (if equipped) ® is a registered trademark DaimlerChrysler AG. The Electronic Stability Program (ESP helps to control the vehicle during corner- ing if the vehicle is understeering or over- steering. It also assists you in maintaining traction while accelerating on loose or slip- pery road surfaces.
Page 168: Slip Indicator Light
® be a malfunction of the ESP sys- tems (other than ABS). You should have the systems inspected by an authorized SUZUKI dealer. NOTE: When the SLIP indicator light comes on and stays on while driving, indicating a ® malfunction of the ESP...
Page 169: Tire Pressure Monitoring System (Tpms)
® be a malfunction of the ESP sys- tems (other than ABS). You should have the systems inspected by an authorized SUZUKI dealer. NOTE: When the “ESP” warning light comes on, or stays on while driving, indicating a mal- ®...
Page 170 Have your vehicle inspected by an autho- rized SUZUKI dealer. Even if the light turns off after blinking, indicating that the monitoring system has recovered, make sure to have an authorized SUZUKI dealer check the system.
Page 171 WARNING If the low tire pressure warning light comes on and stays on, reduce your speed and avoid abrupt steering and braking. Stop in a safe place as soon as possible and check your tires. • If you have a flat tire, replace it with the spare tire.
Page 172 Have your vehicle inspected by an authorized SUZUKI dealer. TPMS Limitations The tire pressure monitoring system may not function properly under certain circum- stances. In the following situations, the low tire pressure warning light may come on and remain on or may blink.
Page 173: Break-In
• When you use non-genuine SUZUKI wheels or tires. Replacing Tires and/or Wheels If you get a flat tire, Suzuki recommends that you have an authorized SUZUKI dealer mount a new tire on the wheel that had the flat tire, and reinstall this tire on the vehicle in place of the spare.
Page 174: Catalytic Converter
OPERATING YOUR VEHICLE Catalytic Converter 54G236 The purpose of the catalytic converter is to minimize the amount of harmful pollutants in your vehicle’s exhaust. Use of leaded fuel in vehicles equipped with catalytic converters is prohibited by federal law, because lead deactivates the pollutant- reducing components of the catalyst sys- tem.
Page 175: Improving Fuel Economy
Improving Fuel Economy The following instructions will help you improve fuel economy. Avoid excessive idling If you are to wait for more than a minute while you are parked, stop the engine and start it again later. When warming up a cold engine, allow the engine to idle until the temperature gauge pointer comes up to the “C”...
Page 176 OPERATING YOUR VEHICLE MEMO 6-21...
Page 177: Driving Tips
DRIVING TIPS DRIVING TIPS Highway Driving ... 7-1 Driving on Hills ... 7-1 Driving on Slippery Roads ... 7-2 60G409...
Page 178: Highway Driving
DRIVING TIPS 52D078S WARNING • Wear Your Seat Belts at All Times. Even though air bags are equipped at the front seating positions, the driver and all passengers should be properly restrained at all times, using the seat belts provided. Refer to the “Seat Belts and Child Restraint Systems”...
Page 179: Driving On Slippery Roads
WARNING Try not to hold the brake pedal down too long or too often while going down a steep or long hill. This could cause the brakes to overheat, result- ing in reduced braking efficiency. Failure to take this precaution could result in loss of vehicle control.
Page 180: Tire Chains
MAINTENANCE” section details. • Do not use tires other than those specified by SUZUKI. Never use dif- ferent sizes or types of tires on the front and rear wheels. For informa- tion regarding the specified tires, refer to the Tire Information Label located on the driver’s side door...
Page 181 WARNING (Continued) • Never use oversized tires or special shocks and springs to raise (jack up) your vehicle. This will change its handling characteristics. Over- sized tires may also rub against the fender over bumps, causing vehicle damage or tire failure. •...
Page 182 DRIVING TIPS MEMO...
Page 183: Vehicle Loading And Towing
VEHICLE LOADING AND TOWING VEHICLE LOADING AND TOWING Vehicle Loading ... 8-1 Trailer Towing ... 8-2 Towing Your Vehicle (recreational towing) ... 8-2 54G215...
Page 184: Vehicle Loading
VEHICLE LOADING AND TOWING Vehicle Loading 80JS025 Your vehicle was designed for specific weight capacities. The weight capacities of your vehicle are indicated by the Gross Vehicle Weight Rating (GVWR), the Gross Axle Weight Rating (GAWR, front and rear) and the Vehicle Capacity Weight. The GVWR and GAWR (front and rear) are listed on the Safety Certification Label which is located below the driver’s side...
Page 185: Trailer Towing
Trailer Towing 54G639 Do not use your vehicle to tow a trailer. The vehicle is not designed or intended for such use. Towing a trailer can adversely affect handling, durability and fuel econ- omy. Towing Your Vehicle (recreational towing) Your vehicle may be towed behind another vehicle (such as a motorhome), provided you use the proper towing method speci- fied for your vehicle.
Page 186 VEHICLE LOADING AND TOWING TOWING METHOD A FROM THE FRONT: FRONT WHEELS ON A DOLLY AND REAR WHEELS ON THE GROUND A: 2WD (except 2WD mode of i-AWD) VEHICLES WITH MANUAL SAXLE OR AUTOMATIC TRANSAXLE 1) Secure the front wheels on a towing dolly according to the instructions pro- vided by the dolly manufacturer.
Page 187 TOWING METHOD B FROM THE FRONT: FOUR WHEELS ON THE GROUND VEHICLE LOADING AND TOWING B: 2WD or i-AWD (including 2WD mode) VEHICLES WITH MANUAL TRANSAXLE 1) Shift the manual transaxle lever into neutral. 2) Turn the ignition key to the “ACC” posi- tion to unlock the steering wheel.
Page 188 VEHICLE LOADING AND TOWING MEMO...
Page 189: Inspection And Maintenance
INSPECTION AND MAINTENANCE INSPECTION AND MAINTENANCE Maintenance Schedule ... 9-2 Periodic Maintenance Schedule ... 9-3 Maintenance Recommended under Severe Driving Conditions ... 9-7 Engine Oil and Filter ... 9-11 Gear Oil ... 9-14 Automatic Transaxle Fluid ... 9-16 Engine Coolant ... 9-17 Windshield Washer Fluid ...
Page 190 “LOCK” position for at least 90 seconds before performing any electrical service work on your SUZUKI. Do not touch air bag sys- tem components or wires. The wires are wrapped with yellow tape or yellow tubing, and the couplers are yellow for easy identification.
Page 191: Maintenance Schedule
SUZUKI recommends that mainte- nance on items marked with an aster- performed your authorized SUZUKI dealer or a quali- fied service technician. If you are qualified, you may perform mainte- nance on the unmarked items by referring to the instructions in this section.
Page 192: Periodic Maintenance Schedule
INSPECTION AND MAINTENANCE Periodic Maintenance Schedule R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary Interval: This interval should be judged by odometer reading or months, whichever comes first. ENGINE & EMISSION CONTROL 1. Drive belt *Tension check, *adjustment, *replacement *2.
Page 193 SUZUKI, however, urges that all recommended maintenance services be performed at the indicated inter- vals and the maintenance recorded.
Page 194 INSPECTION AND MAINTENANCE R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary Interval: This interval should be judged by odometer reading or months, whichever comes first. CHASSIS AND BODY 1. Clutch (for manual transaxle) Pedal and fluid level *2.
Page 195 R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary Interval: This interval should be judged by odometer reading or months, whichever comes first. CHASSIS AND BODY 1. Clutch (for manual transaxle) Pedal and fluid level *2.
Page 196: Maintenance Recommended Under Severe Driving Conditions
INSPECTION AND MAINTENANCE Maintenance Recommended under Severe Driving Conditions Follow this schedule if your car is mainly operated under one or more of the following conditions: • When most trips are less than 6 kilometers (4 miles) • When most trips are less than 16 kilometers (10 miles) and outside temperature remain below freezing. •...
Page 197 R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary Interval: This interval should be judged by odometer reading or months, whichever comes first. ENGINE & EMISSION CONTROL 1. Drive belt *Tension check, *adjustment, *replacement *2. Valve lash (clearance) 3.
Page 198 INSPECTION AND MAINTENANCE R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary Interval: This interval should be judged by odometer reading or months, whichever comes first. CHASSIS AND BODY 1. Clutch (for manual transaxle) Pedal and fluid level *2.
Page 199 R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary Interval: This interval should be judged by odometer reading or months, whichever comes first. CHASSIS AND BODY 1. Clutch (for manual transaxle) Pedal and fluid level *2.
Page 200: Specified Oil
INSPECTION AND MAINTENANCE Engine Oil and Filter Specified Oil 10W-30 5W-30 Temperature EXAMPLE “Starburst” 52D083 (1) Preferred Use engine oil with the American Petro- leum Institute Certified For Gasoline Engines “Starburst” symbol. Select the appropriate oil viscosity accord- ing to the above chart. We highly recommend you use SAE 5W- 30 oil.
Page 201: Refilling
Refilling EXAMPLE Open Close 81A147 Remove the oil filler cap and pour oil slowly through the filler hole to bring the oil level to the upper limit on the dipstick. Be careful not to overfill. Too much oil is almost as bad as too little oil.
Page 202 Check for leaks again. CAUTION When replacing the oil filter, it is rec- ommended that you use a genuine SUZUKI replacement filter. If you use an after-market filter, make sure it is of equivalent quality and carefully fol- low the manufacturer’s instructions...
Page 203: Gear Oil
If you find any leaks or are not sure that the filter has been properly tightened, have the vehicle inspected by your SUZUKI dealer. Gear Oil Specified Gear Oil Manual transaxle (API GL-4)
Page 204: Gear Oil Replacement
(1) until the oil level reaches the bottom of the filler hole. Gear Oil Replacement Since special procedures, materials and tools are required to change the automatic transaxle oil, it is recommended that you trust this job to your authorized SUZUKI dealer.
Page 205: Automatic Transaxle Fluid
Automatic Transaxle Fluid Specified Fluid Use an automatic transaxle fluid equivalent ® to DEXRON -III. Fluid Level Check CAUTION Driving with too much or too little fluid can damage the transaxle. You must check the fluid level with the automatic transaxle fluid at normal operat- ing temperature.
Page 206: Engine Coolant
After checking or adding oil, be sure to insert the dipstick securely. Changing Oil Since special procedures, materials and tools are required to change the automatic transaxle oil, it is recommended that you trust this job to your authorized SUZUKI dealer. 9-17 Engine Coolant 56KN049 EXAMPLE...
Page 207: Coolant Replacement
Solution can be poisonous to animals. Keep out of the reach of children and animals. INSPECTION AND MAINTENANCE Coolant Replacement Since special procedures are required, we recommend you take your vehicle to your SUZUKI dealer for coolant replacement. 9-18...
Page 208: Windshield Washer Fluid
INSPECTION AND MAINTENANCE Windshield Washer Fluid (or opposite side) 65D108 80J008 9-19 Check that there is washer fluid in the tank by looking at the washer fluid level gauge which is attached to the cap of the washer fluid tank. If the fluid level is near “E” mark, refill it.
Page 209: Spark Plugs
“SPECIFICATIONS” section at the end of this book. If you wish to use a brand of spark plug other than the specified plugs, consult your SUZUKI dealer. INSPECTION AND MAINTENANCE 1.0 – 1.1 mm (0.039 – 0.043 in.)
Page 210: Brakes
Should the light come on, immedi- ately ask your SUZUKI dealer to inspect the brake system. • A rapid fluid loss indicates a leak in the brake system which should be inspected by your SUZUKI dealer immediately.
Page 211: Brake Pedal
If the pedal to floor carpet distance as measured above is less than the minimum distance required, have your vehicle inspected by your SUZUKI dealer. 60G104 NOTE: When measuring the distance between the...
Page 212: Steering Wheel
If the parking brake is not properly adjusted or the brakes drag after the lever has been fully released, have the parking brake inspected and/or adjusted by your SUZUKI dealer. 9-23 Steering Wheel “c” 80J005 Steering wheel play “c”...
Page 213: Clutch Pedal
If clutch dragging is felt with the pedal fully depressed, have the clutch inspected by your SUZUKI dealer. If the clutch fluid level is near the “MIN” line, fill it up to the “MAX” line with DOT3 brake fluid.
Page 214: Tire Size
E. Rim Diameter This two-digit number is the wheel or rim diameter in inches. WARNING Your SUZUKI is equipped with tires which are all the same type and size. This is important to ensure proper steering and handling of the vehicle.
Page 215: Tire Inflation Pressure
Tire Inflation Pressure Tire inflation pressure should be checked when the tire is cold. “Cold tire inflation pressure” is the pressure in a tire that has been driven less than 1 mile (1.6 km) or has been standing for three hours or more. 80JS025 The front and rear tire pressure specifica- tions for your vehicle are shown below and...
Page 216 5) Check that there are no nails, stones or other objects sticking into the tires. WARNING Your SUZUKI is equipped with tires which are all the same type and size. This is important to ensure proper steering and handling of the vehicle.
Page 217 The following informa- tion will help you understand the grading system, which applies to vehicles sold in the U.S. Consult your SUZUKI dealer or tire retailer for help in choosing the correct replacement tires for your vehicle.
Page 218: Tire Rotation
INSPECTION AND MAINTENANCE Temperature – A, B, C The temperature grades are A (the high- est), B and C, representing the tire’s resis- tance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 219 Compact Spare Tire (if equipped) 54G115 (1) Wear indicator (2) Indicator location mark Your vehicle comes equipped with the compact spare tire. The compact spare is designed to save space in your storage area, and its lighter weight makes it easier to install if a flat tire occurs.
Page 220: Changing Wheels
SUZUKI recommends mounting radial snow tires on all four wheels. Snow tires must be the same size as the standard tires. Also be sure to use the tires of the same type and brand on all four wheels of...
Page 221 GLOSSARY OF TIRE TERMINOL- Accessory Weight – the combined weight (in excess of those standard items which may be replaced) of automatic transaxle, power steering, power brakes, power win- dows, power seats, radio, and heater, to the extent that these items are available as factory-installed equipment (whether...
Page 222 INSPECTION AND MAINTENANCE Vehicle Loading Your vehicle was designed for specific load capacities. The load capacities of your vehicle are indicated by the Gross Vehicle Weight Rating (GVWR), the Gross Axle Weight Rating (GAWR, front and rear), and the total load capacity, the seating capac- ity, and the cargo load capacity.
Page 223 Steps for Determining Correct Load Limit 1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2) Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Page 224: Battery
INSPECTION AND MAINTENANCE Battery EXAMPLE 60A269 WARNING Batteries produce flammable hydro- gen gas. Keep flames and sparks away from the battery or an explosion may occur. Never smoke when work- ing near the battery. WARNING When checking or servicing the bat- tery, disconnect the negative cable.
Page 225: Fuses In The Engine Compartment
Fuses in the Engine Compartment 80J051 (4) (5) (6) (7) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19) (30) (20) (21) (22) (23) (24) (25) (26) (27) (29) (28) 80J052 MAIN FUSE / PRIMARY FUSE All electric load Power window, Ignition, Wiper, Starter Tail light, Rear defogger,...
Page 226 If the main fuse or a primary fuse blows, be sure to have your vehicle inspected by an authorized SUZUKI dealer. Always use a genuine SUZUKI replacement. Never use a substitute such as a wire even for a temporary fix, or extensive electrical damage and a fire can result.
Page 227 (21) Rear defogger (22) Horn / Hazard (23) Audio SX4 SEDAN (21) (24) (1) (2) (3) (4) (5) (6) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (22) (23) 80JC003 MAIN FUSE / PRIMARY FUSE Rear wiper Ignition coil Back-up light...
Page 228: Headlight Aiming
Frequent replacement of a bulb indi- cates the need for an inspection of the electrical system. This should be carried out by your SUZUKI dealer. NOTE: If it is difficult to replace headlight bulbs or parking light bulbs due to under-hood com-...
Page 229 Center Interior Light (if equipped) 60G115 Pull down the lens by using a plain screw driver covered with a soft cloth as shown. To install it, simply push it back in. The bulb can be removed by simply pulling it out. When replacing the bulb, make sure that the contact springs are holding the bulb securely.
Page 230 INSPECTION AND MAINTENANCE Bulb EXAMPLE 54G124 (3) Removal (4) Installation There are two types of bulb, “Full glass type” (1) and “Glass/metal type” (2). To remove and install a full glass type bulb (1), simply pull out or push in the bulb. To remove a glass metal type bulb (2) from a bulb holder, push in the bulb and turn it counterclockwise.
Page 231 Rear combination light (tail, stop, turn signal, etc.) 79J014 SX4 SEDAN 80JC046 Spot light 79J131 INSPECTION AND MAINTENANCE License plate light 75F087 SX4 SEDAN EXAMPLE 56KN048 9-42...
Page 232 INSPECTION AND MAINTENANCE Luggage compartment light (SX4) 79J015 Trunk room light (SX4 SEDAN) 56KN004 9-43 High-mount stop light (if equipped) 80J100 To remove a high-mounted stop light hous- ing the following procedure: 1) Open the tailgate, and remove the nuts (1) as shown in the illustration.
Page 233: Wiper Blades
NOTE: Some wiper blades may be different from the ones described here depending on vehicle specifications. If so, consult your SUZUKI dealer for proper replacement method. 9-44...
Page 234 INSPECTION AND MAINTENANCE For windshield wipers and some rear wipers: 70G119 1) Hold the wiper arm away from the win- dow. NOTE: When raising both of the front wiper arms, pull the driver’s side wiper arm up first. When returning the wiper arms, lower the passenger’s side wiper arm first.
Page 235 52D124 (3) Retainer 4) If the new blade is provided without the two metal retainers, move them from the old blade to the new one. Installation 52D125 (4) Locked end 5) Install the new blade in the reverse order of removal, with the locked end positioned toward the wiper arm.
Page 236 INSPECTION AND MAINTENANCE 3) When reinstalling wiper frame to arm, install the wiper frame in the reverse order of removal. To remove and install some types of rear wiper blade from and to the wiper frame. Removal 52D104 1) Flex the locked end of blade (3) away from retainer (4) to unlock it and slide the blade out as shown.
Page 237: Air Conditioning System
INSPECTION AND MAINTENANCE Air Conditioning System If you do not use the air conditioner for a long period, such as during winter, it may not give the best performance when you start using it again. To help maintain opti- mum performance and durability of your air conditioner, it needs to be run periodically.
Page 238 INSPECTION AND MAINTENANCE MEMO 9-49...
Page 239: Emergency Service
EMERGENCY SERVICE EMERGENCY SERVICE Jacking Instructions ... 10-1 Jump Starting Instructions ... 10-3 Towing a Disabled Vehicle ... 10-4 If the Starter Does Not Operate ... 10-4 If the Engine is Flooded ... 10-5 If the Engine Overheats ... 10-5 If You Can Not Shift Automatic Transaxle Gearshift Lever Out of “P”...
Page 240: Jacking Instructions
EMERGENCY SERVICE Jacking Instructions 80JC014 SX4 SEDAN 80JC045 10-1 75F062 1) Place the vehicle on level, hard ground. 2) Set the parking brake firmly and shift into “P” (Park) if your vehicle has an automatic transaxle, or shift into “R” (Reverse) if your vehicle has a manual transaxle.
Page 241 front 80J085 6) Position the jack at an angle as shown in the illustration and raise the jack by turning the jack handle clockwise until the jack-head groove fits around the jacking bar beneath the vehicle body. 7) Continue to raise the jack slowly and smoothly until the tire clears the ground.
Page 242: Jump Starting Instructions
• If your battery discharges repeat- edly, for no apparent reason, have your vehicle inspected by an autho- rized SUZUKI dealer. • To avoid harm to yourself or dam- age to your vehicle or battery, fol- low the jump starting instructions below precisely and in order.
Page 243: Towing A Disabled Vehicle
2) If the headlights remain bright, check the fuses. If the reason for failure of the starter is not obvious, there may be a major electrical problem. Have the vehi- inspected your authorized SUZUKI dealer. 10-4...
Page 244: If The Engine Is Flooded
EMERGENCY SERVICE If the Engine is Flooded If the engine is flooded with gasoline, it may be hard to start. If this happens, press the accelerator pedal all the way to the floor and hold it there while cranking the engine.
Page 245: If You Can Not Shift Automatic Transaxle Gearshift Lever Out Of "P" (Park)
If the temperature indication does not return to the normal condition: 1) Turn off the engine and check that the water pump belt and pulleys are not damaged or slipping. If any abnormality is found, correct it. 2) Check the coolant level in the reservoir. If it is found to be lower than the “LOW”...
Page 246 EMERGENCY SERVICE 3) Make sure the key is in the “ON” or “ACC” position. 4) Remove the cover (1) over the button. 5) With pushing the release button by the key or the flat end rod, shift the gear- shift lever to the desired position. This procedure is for emergency use only.
Page 247: Appearance Care
APPEARANCE CARE APPEARANCE CARE Corrosion Prevention ... 11-1 Vehicle Cleaning ... 11-3 60G412...
Page 248: Corrosion Prevention
APPEARANCE CARE Corrosion Prevention It is important to take good care of your vehicle to protect it from corrosion. Listed below are instructions for how to maintain your vehicle to prevent corrosion. Please read and follow these instructions carefully. Important Information About Corrosion Common causes of corrosion 1) Accumulation of road salt, dirt, moisture...
Page 249 The fittings for such guards should also be corrosion resistant. Please check with your autho- rized SUZUKI dealer for information on these guards. Store your vehicle in a dry, well-venti- lated area Do not park your vehicle in a damp, poorly ventilated area.
Page 250: Vehicle Cleaning
APPEARANCE CARE Vehicle Cleaning 76G044S WARNING When cleaning the interior or exterior of the vehicle, NEVER USE flammable solvents such lacquer thinners, gas- oline, benzene or cleaning materials such as bleaches and strong house- hold detergents. The materials could cause personal injury or damage to the vehicle.
Page 251 Washing WARNING • Never attempt to wash and wax your vehicle with the engine run- ning. • When cleaning the underside of the body and fender, where there may be sharp-edged parts, you should wear gloves and a long-sleeved shirt to protect your hands and arms from being cut.
Page 252 APPEARANCE CARE Waxing 60B211S After washing the vehicle, waxing and pol- ishing are recommended to further protect and beautify the paint. • Only use waxes and polishes of good quality. • When using waxes polishes, observe the precautions specified by the manufacturers.
Page 253: General Information
GENERAL INFORMATION GENERAL INFORMATION Identification Numbers ... 12-1 Safety Certification Label ... 12-2 Emission Compliance Label (for U.S.A.) ... 12-2 Warranties ... 12-2 On-Board Vehicle Computers and Event Data Recorders ... 12-3 Reporting Safety Defects ... 12-4 54G072...
Page 254: Identification Numbers
GENERAL INFORMATION Identification Numbers Vehicle Identification Number EXAMPLE (for some vehicles) 60G152 12-1 The Vehicle Identification Number (VIN) may be found in the location shown in the above illustrations. This number is used to register the vehicle. It is also used to assist your dealer when ordering parts or refer- ring to special service information.
Page 255: Safety Certification Label
For U.S.A. The following warranties are provided with your vehicle: • New Vehicle Limited Warranty • Limited Warranty For SUZUKI Parts or Accessories • Emission Components Defect Warranty • Emission Performance Warranty 12-2...
Page 256: On-Board Vehicle Computers And Event Data Recorders
SUZUKI’s defense of litiga- tion through the discovery process, or as required by law. In addition, once SUZUKI collects or...
Page 257: Reporting Safety Defects
War- ranty Information booklet. For vehicles registered for use and principally operated in Canada please contact Suzuki Canada Inc. at 1-905- 889-2677 extension 2254 or write to: Suzuki Canada Inc. Customer Relations 100 East Beaver Creek Road...
Page 258 GENERAL INFORMATION MEMO 12-5...
Page 259: Fuses And Protected Circuits
FUSES AND PROTECTED CIRCUITS COLOR/SIZE (AMPS) BLACK (80) RED (50) RED (50) – MAIN – FUSE BLUE (15) BLUE (15) YELLOW (20) – (10) GREEN (40) (4) (5) (6) (7) (12) (13) (14) (20) (21) (23) (24) PROTECTED CIRCUIT All electric load Power window, Ignition, Wiper, Starter Tail light, Rear defogger, Door lock, Hazard/Horn, Dome Blank...
Page 260 FUSES AND PROTECTED CIRCUITS COLOR/SIZE (AMPS) (11) PINK (30) (12) PINK (30) (13) PINK (30) (14) RED (50) MAIN (15) PINK (30) FUSE (16) YELLOW (20) (17) BLUE (15) (18) BLUE (15) (19) BLUE (15) (20) – 13-2 (4) (5) (6) (7) (12) (13) (14) (20)
Page 261 COLOR/SIZE (AMPS) (21) – (22) – (23) – (24) – MAIN (25) – FUSE (26) – (27) – (28) – (29) – (30) – (4) (5) (6) (7) (12) (13) (14) (20) (21) (23) (24) PROTECTED CIRCUIT Air compressor relay Fuel pump relay Condensor fan relay Front fog light relay...
Page 262 FUSES AND PROTECTED CIRCUITS COLOR/SIZE (AMPS) BLUE (15) BLUE (15) RED (10) RED (10) BLUE (15) FUSE BLUE (15) PINK (30) GREEN (30) RED (10) (10) BLUE (15) (11) RED (10) 13-4 (1) (2) (3) (4) (5) (6) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23)
Page 263 COLOR/SIZE (AMPS) (12) BLUE (15) (13) BLUE (15) (14) YELLOW (20) (15) – (16) RED (10) (17) BLUE (15) FUSE (18) RED (10) (19) RED (10) (20) BLUE (15) (21) GREEN (30) (22) BLUE (15) (23) BLUE (15) (1) (2) (3) (4) (5) (6) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18)
Page 264 FUSES AND PROTECTED CIRCUITS SX4 SEDAN COLOR/SIZE (AMPS) BLUE (15) BLUE (15) RED (10) RED (10) BLUE (15) BLUE (15) FUSE PINK (30) GREEN (30) RED (10) (10) BLUE (15) (11) RED (10) (12) – 13-6 (21) (24) (1) (2) (3) (4) (5) (6) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17)
Page 265 COLOR/SIZE (AMPS) (13) BLUE (15) (14) YELLOW (20) (15) – (16) RED (10) (17) BLUE (15) (18) RED (10) FUSE (19) RED (10) (20) BLUE (15) (21) GREEN (30) (22) BLUE (15) (23) BLUE (15) (24) GREEN (30) (21) (24) (1) (2) (3) (4) (5) (6) (8) (9) (10) (11) (12) (13) (14) (15) (16)
Page 266 FUSES AND PROTECTED CIRCUITS MEMO 13-8...
Page 267: Specifications
SPECIFICATIONS NOTE: Specifications are subject to change with- out notice. ITEM: Dimensions Overall length Overall width Overall height Wheelbase Track Ground clearance ITEM: Weight Gross axle weight rating Gross vehicle weight rating Vehicle capacity weight M/T: Manual transaxle A/T: Automatic transaxle UNIT: mm (in.) 4115 –...
Page 268 SPECIFICATIONS ITEM: Engine Type Number of cylinders Bore Stroke Piston displacement Compression ratio ITEM: Electrical Ignition timing Standard spark plug Battery Fuses 14-2 J20A (16V DOHC) 84.0 mm (3.31 in.) 90.0 mm (3.54 in.) 1995 cm (1995cc, 121.7 cu.in) 10.5 : 1 3°...
Page 269 ITEM: Light Headlight Front fog light Front turn signal light Rear turn signal light Parking light Brake/tail light License plate light Reversing light Dome light Luggage compartment light Spot light High mount stop light Side marker light WATTAGE 12V 65/55W 12V 55W 12V 21W 12V 21W...
Page 270 SPECIFICATIONS ITEM: Wheel Tire size, front and rear Tire pressure ITEM: Steering Camber angle Caster angle ITEM: Capacities Coolant (including reserve tank) Fuel tank Engine oil (replaced with filter) Transaxle oil Rear differential oil Transfer gear box oil 14-4 P195/65R15, P205/60R16 SX4 SEDAN P195/65R15, P205/50R17 For the specified tire pressure, see the Tire Information Label located...
Page 271: Index
INDEX Symbols “CRUISE” Indicator Light... 4-8 “ESP OFF” Indicator Light... 4-6, 6-14 “ESP OFF” Switch ... 4-13 “ESP” (Electronic Stability Program) Warning Light ... 4-5 “ESP” Warning Light... 6-13 “PASS AIRBAG OFF” Indicator... 4-20 “SET” Indicator Light ... 4-8 Numerics 2WD/i-AWD (intelligent All Wheel Drive) Switch...
Page 272 INDEX Daytime Running Light (D.R.L.) Indicator Light... 4-10 Daytime Running Light (D.R.L.) System... 3-5 Door Locks ... 2-1 Driver’s Seat Belt Reminder Light... 4-6 Driving on Hills ... 7-1 Driving on Slippery Roads... 7-2 Electric Power Steering Light... 4-8 Electronic Stability Program (ESP®) ... 6-12 Emergency Locking Retractor (ELR) ...
Page 273 If You Can Not Shift Automatic Transaxle Gearshift Lever Out of “P” (PARK) ... 10-6 If Your Vehicle Gets Stuck ... 7-2 Ignition Key Reminder... 2-1 Ignition Switch ... 3-1 Improving Fuel Economy... 6-20 Information Display ... 4-17 Inside Rearview Mirror ... 2-18 Installation of Child Restraint with Top Strap...
Page 274 INDEX Periodic Maintenance Schedule... 9-3 Power Assisted Brakes ... 6-9 Power Door Locking System ... 2-2 Power Mirror Control... 2-19 Power Steering... 9-23 Power Steering Fluid ... 9-23 Power Window Controls ... 2-16 Radio Antenna ... 4-38, 5-16 Rear Window Wiper/Washer Switch ... 3-8 Refill with Oil and Check for Leaks...
Page 275 INDEX Traction Control System ... 6-12 Trailer Towing ... 8-2 Trip meter ... 4-11 Troubleshooting ... 4-57 Trunk Lid ... 2-15 Trunk Light ... 5-15 Turn Signal Indicators... 4-9 Turn Signal Operation ... 3-6 Uniform Tire Quality Grading ... 9-28 Using the 2WD/i-AWD (intelligent All Wheel Drive) Switch ...
Page 276 INDEX MEMO 15-6...
Page 277 Prepared by June, 2007 Part No. 99011-80J21-03E Printed in Japan TP274...
Page 278 SERVICE STATION INFORMATION Fuel recommendation: See page 1-1 Engine oil recommendation: Engine oil with “Starburst” symbol For further details, see “Engine Oil and Filter” in the “INSPECTION AND MAINTENANCE” section. Brake and clutch fluid: DOT3 Automatic transaxle fluid: An equivalent of DEXRON ® -III. Tire cold pressure: See the “Tire Information Label”...

This manual is also suitable for:

2008 sx4 sedan Sx4 sedan 2008

Suzuki SX4/SX4 SEDAN Owner's Manual

Table of Contents

Before Driving

Steering Column Controls

Instrument Panel

Other Controls and Equipment

Operating Your Vehicle

Inspection and Maintenance

Emergency Service

Quick Links

Chapters

Related Manuals for Suzuki SX4/SX4 SEDAN

Summary of Contents for Suzuki SX4/SX4 SEDAN

This manual is also suitable for: