Engine General Information And Diagnosis; Precautions; Precautions On Engine Service; Precautions In Diagnosing Trouble - Suzuki Grand Vitara Service Manual
Hide thumbs
Also See for Grand Vitara:
- Owner's manual (1736 pages) ,
- Service manual (836 pages) ,
- Supplementary service manual (481 pages)
Table of Contents
1A-1 Engine General Information and Diagnosis:
Engine General Information and Diagnosis
Precautions on Engine Service
CAUTION
!
The following information on engine service
should be noted carefully, as it is important in
preventing damage, and in contributing to
reliable engine performance.
• When raising or supporting engine for any reason, do
not use a jack under oil pan. Due to small clearance
between oil pan and oil pump strainer, jacking against
oil pan may cause it to be bent against strainer,
resulting in damaged oil pick-up unit.
• It should be kept in mind, while working on engine,
that 12-volt electrical system is capable of violent and
damaging short circuits.
When performing any work where electrical terminals
can be grounded, ground cable of the battery should
be disconnected at battery.
• Any time the air cleaner, throttle body or intake
manifold is removed, the intake opening should be
covered. This will protect against accidental entrance
of foreign material which could follow intake passage
into cylinder and cause extensive damage when
engine is started.
Precautions in Diagnosing Trouble
• Don't disconnect couplers from ECM, battery cable
from battery, ECM ground wire harness from engine
or main fuse before confirming diagnostic information
(DTC, freeze frame data, etc.) stored in ECM memory.
Such disconnection will erase memorized information
in ECM memory.
• Diagnostic information stored in ECM memory can be
cleared as well as checked by using SUZUKI scan
tool or OBD generic scan tool (Vehicle without
diagnosis connector). Before using scan tool, read its
Operator's (Instruction) Manual carefully to have good
understanding as to what functions are available and
how to use it.
It is indistinguishable which module turns on MIL
because not only ECM but also TCM (for A/T model)
turns on MIL (For details of on-board diagnostic
system for A/T model, refer to "On-Board Diagnostic
System Description: in Section 5A". Therefore, check
both ECM and TCM (for A/T model) for DTC when
MIL lights on.
When checking ECM for DTC, keep in mind that DTC
is displayed on the scan tool as follows depending on
the scan tool used.
– SUZUKI scan tool displays DTC detected by ECM.
www.CarGarage.ir
Precautions
– OBD generic scan tool displays DTC detected by
S5JB0A1100001
each of ECM and TCM (for A/T model)
simultaneously.
• Priorities for diagnosing troubles
If two or more DTCs are stored, proceed to the DTC
flow which has been detected earliest in the order and
follow the instruction in that flow.
If no instructions are given, troubleshoot DTCs
according to the following priorities.
a. DTCs other than DTC P0171 / P0172 (Fuel
system too lean / too rich), DTC P0300 / P0301 /
P0302 / P0303 / P0304 (Misfire detected) and
DTC P0401 / P0402 (EGR flow malfunction)
b. DTC P0171 / P0172 (Fuel system too lean / too
rich) and DTC P0401 / P0402 (EGR flow
malfunction)
c. DTC P0300 / P0301 / P0302 / P0303 / P0304
(Misfire detected)
• Be sure to read "Precautions for Electrical Circuit
Service: in Section 00" before inspection and observe
what is written there.
• ECM replacement:
When substituting a known-good ECM, check for the
following conditions. Neglecting this check may cause
damage to a known-good ECM.
– Resistance value of all relays, actuators is as
specified respectively.
S5JB0A1100002
– MAP sensor, electric load current sensor (for J20
engine), A/C refrigerant pressure sensor (if
equipped with A/C), accelerator pedal position
(APP) sensor, TP sensor and CO adjust resistor (if
not equipped with A/F sensor) are in good condition
and none of power circuits of these sensors is
shorted to ground.
• Communication of ECM, BCM, combination meter,
keyless start control module (if equipped) ABS
hydraulic unit / control module assembly, 4WD control
module (for J20 engine) and TCM (for A/T model), is
established by CAN (Controller Area Network). (For
more detail of CAN communication for ECM, refer to
"CAN Communication System Description: ").
Therefore, handle CAN communication line with care
referring to "Precaution for CAN Communication
System: in Section 00".
• Immobilizer transponder code registration after
replacing ECM
When ECM is replaced with new one or with another
one, make sure to register immobilizer transponder
code to ECM correctly according to "Procedure after
ECM Replacement: in Section 10C".
www.CarGarage.ir
Table of Contents
