Page 4
Nonlinear Editing System Digital I/F Board AY-PB2002E Video Input Signal: Comply with the SMPTE259M standards, BNC x 1 (with active loop-through) Output Signal: Comply with the SMPTE259M standards, BNC x 1 Audio Input Signal: Comply with the AES/EBU standards, BNC x 1 Output Signal: Comply with the AES/EBU standards, BNC x 1 General...
MAJOR OPERATING CONTROLS AND THEIR FUNCTION FRONT PANEL 1. Power On/Off Switch 6. Front Panel Turns the power of this unit on and off. Caution: Do not interrupt the Vent Hole on this panel. Notes: 1. Be sure to turn on the power of this unit after turning 7.
Page 7
REAR PANEL MOUSE SEPIAL 1 SEPIAL 2 PRINTER S-VGA VIDEO(DIGITAL) VIDEO(DIGITAL) AUDIO(AES/EBU) AUDIO(AES/EBU) SCSI AUDIO SCSI VIDEO 1 SCSI VIDEO 2 SCSI VIDEO 3 CONTROL 1 CONTROL 2 JOG PAD SEE MANUAL ADV REF COMPOSITE G/L IN COMPOSITE TC IN OUT1 LOOP VIDEO...
Page 8
19. SCSI VIDEO Connectors (SCSI VIDEO 1-3) 28. AUDIO IN 1/2 Jacks (IN1, IN2 L/R) (Unbalanced) Connects with the SCSI Video Connector of the Hard Accepts the audio signal. Disk Box AY-EB2000 or WJ-EB1000 via the optional The audio signal supplied to these jacks can be saved in SCSI Cable AY-CA68SR3 for AY-EB2000 or the Hard Disk Box.
Page 9
JOG PAD OPEN UNDO SHIFT 1. Positioner 5. ZOOM / Moves the selection cursor (when selection is Zooms in the time line. confirmed). (SHIFT + ZOOM) Zooms out the time line. 2. Wipe Lever Controls Wipe, Key Size, and Audio Level. 6.
Page 10
8. MARK IN Sets or cancels the starting mark. (SHIFT + MARK IN) Selects the grip of the IN point. 9. PLAY/STOP Plays back or stops. (SHIFT + PLAY /STOP) Plays back between the starting and ending marks. 10. Shuttle Ring Plays back video and audio forward (clockwise) or in reverse (counterclockwise) with variable speed.
Front Panel Video Output Connector or Composite Video Output Fig. 2-1 Connector on the Rear Panel of the AY-NE2000E. Referring to Fig.2-2, remove five screws fixing the Front Terminate the input terminal of the Underscanned Colour Chassis and remove the Front Chassis.
Page 12
4. Adjustment Procedure Connect the Digital Voltmeter to the land between R997 and L742. Refer to the Location of the Test Points and Adjust L742 to obtain 2.1 ± 0.1V DC. Adjusting Controls on page 14. (6). Bch VCO Adjustment Power Board Test Point: Land between R98 and L743 (Bch VCO)
Page 13
700 ± 7 525 mV –20 –40 Fig. 3-5 Fig. 3-3 Note: When using the β Component for the adjustment, adjust it to 756 mV (106 ± 1 IRE). (8). Output P Gain Adjustment Test Point: Video Out P Connector Rear Panel (10).
Page 14
(17). FVCXO1 Frequency Adjustment Test Point: TP202 (FVCXO1) Input Board Adjust: C601 (FVCXO1) Input Board Disconnect all input from the AY-NE2000E. dø Connect the Frequency Counter to TP202. 100% 10° Adjust C601 to obtain 4.433624 MHz ± 5 Hz. 0°...
Page 15
(20). Pedestal Level Adjustment (22). Component C Gain Adjustment Test Point: Video Out Y/C Connector Rear Panel Test Point: Video Out Y/C Connector Rear Panel Adjust: R812 (PED) Input Board Adjust: R809 (COMP C GAIN-1) Input Board Select the CH1-Component Input by the Device setting, R810 (COMP C GAIN-2) Input Board Select the β...
Page 16
(24). Burst Gate Pulse Width 1 Adjustment Set the Gain Control of the Vectorscope to the maximum. Adjust R807 and R808 so that the vector positions at the Test Point: TP211 (BGP-1) Input Board center of the Vectorscope as shown in Fig. 3-16. Adjust: R794 (BGP-1) Input Board...
Aim the Red vector, adjust R800 so that the Red vector Connect the Waveform Monitor to the Video Out Y/C becomes proper position. Connector. Aim the Yellow vector, adjust R802 so that the Yellow Adjust R798 so that the Y signal level becomes 700 ± 7 vector becomes proper position.
Page 18
Before start to adjust the Jog Pad, remove the Measure) to the 3-CH Unbalanced Audio Output Bottom Cover, connect supplied cable between the Connector-R. Jog Pad and AY-NE2000E. Adjust R247 so that the 3-CH Unbalanced Output level becomes – 6.00 ± 0.10 dBs. (34). Wipe High Level Adjustment...
EXPLODED VIEW OF AY-PB2002E Numbers show screws, washers, nuts and etc. Screws Description XSB26+5FX Binding Head Screws XTB3+10CFXK Binding Head Tapping Black Screws Serial No. Label PCB1 PCB2 V I D ( D I ( A E D I O S / E PACKAGING V ID...
Page 35
RTL : Retention Time Limited (No longer available after discontinuing product). REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION YWV2HA1217A3 Shield Parts NONLINEAR WORKSTATION MAIN KIT AY-NE2000E YWV2SA2790A2 Mounting Angle YW1C1A074B Shield Parts MISCELLANEOUS YW1C1A079A Shield Parts YW1K1A095A...
Page 36
REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION Y CSTCS40MX040 R8,11 ERJ6GEYJ101 Carbon 100 ohms 1/16W Ceramic Filter Y YWSSFC1R2A ERJ6GEYJ101 Carbon 100 ohms 1/16W F1,2 Current Fuse R14,15 ERJ6GEYJ560 Carbon 56 ohms 1/16W L1,2 YWCD75100KC Special Coil ERJ6GEY0R00 Carbon 0 ohm 1/16W...