Related Manuals for ABB DNP31.0
Summary of Contents for ABB DNP31.0
- Page 1 Technical description DNP31.0 DeviceNet Interface Data sheet Description The DNP31 devcie allows the connection of the Universal Motor Controller UMC100.3 to a DeviceNet network.
- Page 2 Sign that indicates a potential dangerous situation that can cause human injuries. Terms and Abbreviations Single Mounting Kit for the fieldbus interfaces UMC100.3 Universal Motor Controller Related Documents Technical Documentation Document No. - 2 - DNP31.0 Data sheet Issue: 09.2015...
-
Page 3: Table Of Contents
Class Code 005 (0x05): Connection Object ..................16 Class Code 043 (0x2B): Acknowledge Handler Object ..............19 Class Code 100 (0x64): ABB Discrete Input Object .................19 Class Code 101 (0x65): ABB Discrete Output Object ..............20 Class Code 102 (0x66): ABB Analog Input Object ................20 Class Code 103 (0x67): ABB Analog Output Object ................21... - Page 4 Document History - 4 - DNP31.0 Data sheet Issue: 09.2015...
-
Page 5: Overview
DNP31 DeviceNet communication interface are discussed in chapter Communication. DNP31 Dual colour LEDs for DeviceNet Connector NS MS status display DeviceNet Connector X1: Interface to UMC100.3 From Top From Side - 5 - Data sheet DNP31.0 Issue: 09.2015... -
Page 6: Mechanical Installation
When the module is installed directly on the UMC100.3 the UMC100.3 with DNP31 acts like a device with integrated DeviceNet communication. No additional accessories are needed. Move down DNP31 until DNP31 snapped-in to fix DNP31 on UMC100.3 NS MS Power Image shows UMC100.3 DC - 6 - DNP31.0 Data sheet Issue: 09.2015... -
Page 7: Mounting The Dnp31 Remotely From The Umc100.3
Mounting the DNP31 on the Single Mounting Kit Step 1: Step 2: Step 3: Plug in the communication Move down the DNP31 Move down the DNP31 until connectors. snapped in Move down Step 4: Fix cable with cable ties - 7 - Data sheet DNP31.0 Issue: 09.2015... -
Page 8: Demounting The Dnp31
Demounting the DNP31 Follow the shown procedure for demounting the DNP31 from UMC100.3 or SMK.3. DNP31 NS MS For demounting slightly rotate screw driver and move the DNP31 upwards to loosen snap-in connection. - 8 - DNP31.0 Data sheet Issue: 09.2015... -
Page 9: Electrical Installation
DeviceNet Cables: YR-29790 (Thick DeviceNet Cable) or YR-29832 (Thin DeviceNet Cable) • Maximum Bus Length: 1200 m • Topology: Multi-drop • Serial Communication Type: Asynchronous, half Duplex • Transfer Rate: 125, 250 or 500 kbit/s - 9 - Data sheet DNP31.0 Issue: 09.2015... -
Page 10: Devicenet Line With Dnp31 Directly Connected To Umc100.3 In A Drawout System
Ground wire and cable shield should be connected to prevent common mode voltage between the network devices from drifting outside the allowable limits. DeviceNet Master Termination active UMC100.3 and DNP31 mounted in drawer DeviceNet Cable - 10 - DNP31.0 Data sheet Issue: 09.2015... -
Page 11: Devicenet Line With Dnp31 Mounted Outside A Drawer Using Single Mounting Kit (Smk3.0)
X1 to backside of drawer. (2) CDP18: ready made connec- tion cable from inside drawer to UMC100.3 X1 max. 3m (3) UMC100.3 mounted inside a drawer (4) DeviceNet communication adapter with single mounting kit (SMK3.0). - 11 - Data sheet DNP31.0 Issue: 09.2015... -
Page 12: Diagnosis
– Is the slave address correct? – Are there two devices with the same address in the system? – Power supply turned on? DeviceNet master – Is the correct EDS file used - 12 - DNP31.0 Data sheet Issue: 09.2015... -
Page 13: Devicenet Information About The Properties Of The Dnp31
ABB Discrete Output 102 (0x66) ABB Analog Input 103 (0x67) ABB Analog Output 105 (0x69) ABB Parameter 112 (0x70) ABB Parameter Modular Devices 118 (0x76) ABB Any Data 128 (0x80) ABB Query - 13 - Data sheet DNP31.0 Issue: 09.2015... -
Page 14: Class Code 001 (0X01): Identity Object
The Message Router Object provides a messaging connection point through which a client may address a service to any object class or instance residing in the physical device. Class Attributes None Instance Attributes None Common Services None - 14 - DNP31.0 Data sheet Issue: 09.2015... -
Page 15: Class Code 004 (0X04): Assembly Object
*1) The size of the data array depends on the Consumed Data size of the device connected to the DNP31. For detailed information, please refer to the device manual. Common Services Service Code Class Instance Service Name 14 (0x0E) Get_Attribute_Single 16 (0x10) Set_Attribute_Single - 15 - Data sheet DNP31.0 Issue: 09.2015... -
Page 16: Class Code 005 (0X05): Connection Object
*2) xxxxxx = node address *3) The size of Produced and Consumed Connection depends on the device connected to the DNP31 (as of writing UMC100.3). For detailed information, please refer to the device manual. - 16 - DNP31.0 Data sheet Issue: 09.2015... - Page 17 *3) The size of Produced and Consumed Connection depends on the device connected to the DNP31 (as of writing UMC100.3). For detailed information, please refer to the device manual. *4) If alloc_choice = polled and ack suppression is enabled then value = 0x80. - 17 - Data sheet DNP31.0 Issue: 09.2015...
- Page 18 *4) Transport Class Trigger 0x00 Cyclic, unacknowledged 0x02 Cyclic, acknowledged 0x10 COS, unacknowledged 0x12 COS, acknowledged Common Services Service Code Class Instance Service Name 05 (0x05) Reset 14 (0x0E) Get_Attribute_Single 16 (0x10) Set_Attribute_Single - 18 - DNP31.0 Data sheet Issue: 09.2015...
-
Page 19: Class Code 043 (0X2B): Acknowledge Handler Object
Class Code 100 (0x64): ABB Discrete Input Object The ABB Discrete Input Object models the discrete inputs of the device connected to the DNP31. You can use this object in applications as simple as a toggle switch or as complex as a discrete I/O control module. -
Page 20: Class Code 101 (0X65): Abb Discrete Output Object
Set_Attribute_Single Class Code 102 (0x66): ABB Analog Input Object The ABB Analog Input Object models the analog inputs of the device connected to the DNP31 (as of writ- ing UMC100.3). There is a separate instance for each analog input available on the device. -
Page 21: Class Code 103 (0X67): Abb Analog Output Object
(slot 0) of modular devices. The index always corresponds to the parameter number. The attribute is fixed to 3. The use of the ABB Parameter Object provides a known public interface to a device’s configuration data. In addition, this object also provides all the information necessary to define and describe each of a de- vice’s individual configuration parameters. -
Page 22: Class Code 112 (0X70): Abb Parameter Modular Object
When required details are available on request. Class Code 128 (0x80): ABB Query Object The ABB Query Object provides an array filled with the External IDs of all modules connected to the ad- apter module. It is used for modular devices only By means of this Object, configuration tools are able to read the module configuration from the DNP31. -
Page 23: Technical Data
0 ... +60 °C Storage -25 ... +70 °C Vibration (sinusoidal) acc. to IEC/EN 60068-2-6 (Fc) 0.7 g / 10 ..150 Hz Shock (half-sine) acc. to IEC/EN 60068-2-27 (Ea) 15 g / 11 ms - 23 - Data sheet DNP31.0 Issue: 09.2015... -
Page 24: Dimensions
Connection Cables DNP31 NS MS Function CAN_L Screen CAN_H Color Function Blue Brown Black Communication Grey Communication White Diagnosis 5 4 3 2 1 Drawer CDP24 to UMC100.3 Colors must match CDP18 - 24 - DNP31.0 Data sheet Issue: 09.2015... - Page 25 Problem Description • Steps to reproduce the problem • Version of UMC (Ident number on nameplate and firmware version which is displayed on the UMC100-PAN) • Version of MRP (Ident number on nameplate) - 25 - Data sheet DNP31.0 Issue: 09.2015...
- Page 26 MEMO DNP31.0 Data sheet - 26 - Issue: 09.2015...
- Page 28 With regard to purchase orders, the agreed Phone: +49 (0) 6221 7 01-0 particulars shall prevail. ABB AG does not accept Fax: +49 (0) 6221 7 01-240 any responsibility whatsoever for potential errors or E-Mail: [email protected]...