LG 19HK312C Owner's Manual
  1. Manuals
  2. Brands
  3. LG Manuals
  4. Medical Equipment
  5. 19HK312C
  6. Owner's manual
LG 19HK312C Owner's Manual

LG 19HK312C Owner's Manual

Medical monitor
Hide thumbs Also See for 19HK312C:
Table of Contents

Quick Links

OWNER'S MANUAL
MEDICAL MONITOR
Please read this manual carefully before operating
your set and retain it for future reference.
19HK312C
www.lg.com
Copyright 2018 LG Electronics Inc. All Rights Reserved.
Table of Contents
loading

Related Manuals for LG 19HK312C

Summary of Contents for LG 19HK312C

  • Page 1 OWNER’S MANUAL MEDICAL MONITOR Please read this manual carefully before operating your set and retain it for future reference. 19HK312C www.lg.com Copyright 2018 LG Electronics Inc. All Rights Reserved.
  • Page 2 Authorized representative in the European community. Indicates warning and safety instructions. If not adhered to, it could result LG Electronics European Shared Service Center B.V. in death or serious injury to the user or others. WARNING Krijgsman 1, 1186 DM Amstelveen, The Netherlands...
  • Page 3 SAFETY INFORMATION This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to other devices in the vicinity. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to other devices, which can be determined by turning the equipment off Safety Standard and on, the user is encouraged to try to correct the interference by one or more of the following measures.

  • Page 4: Iden

    DECLARATION OF CONFORMITY The complete Declaration of Conformity may be requested through the following postal address: LG Electronics European Shared Service Center B.V., Krijgsman 1, 1186 DM Amstelveen, The Netherlands or can be requested at our dedicated DoC website: http://www.lg.com/global/support/cedoc/cedoc#...
  • Page 5 Electro-Magnetic Immunity This EUT is intended for use in the electromagnetic environment specified below. The customer or the user of the EUT should assure that it is used in such an environment. Immunity Test IEC 60601-1-2 Test Level Compliance Level Electromagnetic Environment –...
  • Page 6 IEC 60601-1-2 Compliance Immunity Test Electromagnetic Environment – Guidance Test Level Level Conducted disturbances Portable and mobile RF communications equipment should be used no closer to any part of the EUT, induced by RF fields 0,15 MHz – 80 MHz 0,15 MHz –...
  • Page 7 NOTE • At 80 MHz and 800 MHz, the higher frequency range applies. • These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy.
  • Page 8 Test specifications for ENCLOSURE PORT IMMUNITY to RF wireless communications equipment Maximum IMMUNITY Test frequency Band Distance Service Modulation power TEST LEVEL (MHz) (MHz) (V/m) 380 –390 TETRA 400 Pulse modulation 18 Hz GMRS 460, 430 – 470 FM ± 5 kHz deviation 1 kHz sine FRS 460 LTE Band 13, 704 –...
  • Page 9 NOTE • If necessary to achieve the IMMUNITY TEST LEVEL, the distance between the transmitting antenna and the ME EQUIPMENT or ME SYSTEM may be reduced to 1 m. The 1 m test distance is permitted by IEC 61000-4-3. a) For some services, only the uplink frequencies are included. b) The carrier shall be modulated using a 50 % duty cycle square wave signal.
  • Page 10 Symbols Symbols Descriptions Serial number Symbols Descriptions Non-ionizing radiation Refer to instruction manual/ booklet Alternate current WEEE : Waste Electrical and Electronic Equipment Direct current Authorized representative in the European community. Standby symbol CE Marking Warning Temperature limit Caution Humidity limitation UL classified mark of medical equipment as to electrical shock, fire and mechanical hazards only in accordance with ANSI/AAMI ES60601-1 (2005) + AMD 1 (2012), CAN/CSA-C22.2 No.
  • Page 11 Warning The operator must not touch connectors of the monitor and the patient simultaneously. WARNING: To avoid the risk of electric shock, this equipment must only be connected to a supply mains with protective earth. The product has lower breaking capacity type. So do not install at the building power system prospective short-circuit current exceeding 35 A.
  • Page 12 Caution Handling For safety reasons, be sure to turn off the power when monitor is not used. This monitor is contraindicated for pregnant woman. Do not install the ME Equipment in a location without easy disconnect MANUFACTURER will make available on request circuit diagrams, component accessibility.
  • Page 13 SAFETY PRECAUTIONS CAUTION • Ensure that the product is installed at least 100 mm away from the wall for good ventilation to prevent The Safety Precautions are intended to prevent unexpected danger or harm by helping the user to use the deformation of the product or a fire due to the increase in the internal temperature.
  • Page 14 Power-related Precautions CAUTION • Make sure that you do not disconnect the power cord when using the product. WARNING • When the power plug pin or the outlet becomes dusty, make sure that you clean it thoroughly. • Make sure that you do not turn the monitor on and off by plugging and unplugging the power plug •...

  • Page 15: Cdma

    Precautions When Using the Product CAUTION • Do not use or store the product near inflammables. WARNING • Take a break to protect your health and vision when using the product for long periods of time. • Do not push hard against the screen surface or scratch it with your hands or sharp objects, such as a •...
  • Page 16 Precautions for Connecting to Other Medical Precautions When Cleaning the Product Devices The medical LCD monitor’s front protective panel may become damaged when using solvents such as thinner or benzene, acidic, alkaline or corrosive detergents, chemical cleaning fibers, etc. and the finish Take the following precautions before using this product or connecting it to other medical devices.
  • Page 17 How to Use Cleaner Image Sticking Precautions • Prior to cleaning, turn off the monitor and remove the power cable. • Displaying a still image for a prolonged period may damage the screen, resulting in image sticking. Most third-party products have the same issue. Damage resulting from long-term static images is not •...
  • Page 18 LICENCE Each model supports a different license. Visit www.lg.com for more information on licenses. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
  • Page 19 PRODUCT SPECIFICATIONS In order to improve the product, specifications may change without notice. The ~ symbol means alternating current, and the symbol means direct current. LCD Screen Type TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Screen Pixel Pitch 0.294 mm x 0.294 mm Resolution Max Resolution 1280 x 1024 @ 75 Hz...
  • Page 20 Dimensions (mm) Monitor Size (Width x Height x Depth) With Stand 410 x 389.3 x 249.5 Without Stand 410 x 343.8 x 57.6 Weight (Without Packaging) (kg) With Stand Without Stand INFORMATION OF BIOCIDAL SUBSTANCE The Plastic housing contains a biocidal product* to antagonize the growth of bacteria on the material surface. (*Silver zinc zeolite) ANTIMICROBIAL PROPERTIES* BUILT IN THE PLASTIC HOUSING** The antimicrobial properties are applied to the housing of this medical monitor.

  • Page 21: Table Of Contents

    TABLE OF CONTENTS ASSEMBLING AND PREPARING ..22 USING THE MONITOR ....39 TROUBLESHOOTING ......58 - Product Composition ..........22 - Connecting to PC .............39 PRODUCT SPECIFICATIONS ....61 D-SUB Connection - Support Driver and Software ........23 - Preset Mode ............61 DVI-D Connection - Product and Front Adjust Button Description ..24 D-SUB HDMI Connection Front Adjust Button Functions Information...

  • Page 22: Assembling And Preparing

    ASSEMBLING AND PREPARING Product Composition Please check whether all the components are included in the box before using the product. If there are any missing components, contact the retailer where you purchased the product. Note that the product and related components may look different from the images in this user manual. CD (Owner’s manual/Software)/ Power Cord D-SUB Cable...

  • Page 23: Support Driver And Software

    Required and recommended items: You can install the most recent version using the enclosed CD or download it for installation from the LG Electronics website ( www.lg.com ). • Optional items: You can download the most recent version for installation from the LG Electronics website ( www.lg.com ).

  • Page 24: Product And Front Adjust Button Description

    Product and Front Adjust Button Description Front Adjust Button Functions Information Selects the applicable input mode. Brings you directly to the Picture Mode menu. Selects and confirms menus or options * Automatically sets screen to optimal settings in analog video signal. Adjusts screen brightness.

  • Page 25: Input Ports

    Input Ports Back (Bottom) AC-IN AC-IN AC-IN AC-IN...
  • Page 26 Port 1/2, - Input digital video signal. Used for connecting HW Calibrator (Optional Accessory). - A keyboard, mouse, or USB storage device can be connected. Port - Input digital video signal. CAUTION - Using a DVI to HDMI / DP (DisplayPort) to HDMI cable may cause compatibility issues. - Use a certified cable that displays the HDMI logo.

  • Page 27: Moving And Lifting The Monitor

    Moving and Lifting the Monitor When moving or lifting the monitor, follow these instructions to prevent the monitor from being scratched or damaged and to ensure safe transportation, regardless of its shape or size. • It is advisable to place the monitor in the original box or packing material before attempting to move it. •...

  • Page 28: Installing The Monitor

    Installing the Monitor Cable Holder Assemble the Stand * Assemble the Cable Holder. • Note that the product may look different from the illustrations in this user manual. Stand Body Stand Base CAUTION • To protect the screen from scratches, cover the surface with a soft cloth.
  • Page 29 NOTE • Press the stand until the button rises to maximum height. CAUTION • Illustrations in this document represent typical procedures, so they may look different from the actual product. • Do not use foreign substances (oil, lubricants) when assembling the product. (This may damage the product.) •...

  • Page 30: Tidying Up Cables

    Tidying up Cables Installing on a Table Arrange the cables using cable holders as shown in the illustration. Lift the monitor and place it on the table in an upright position. Leave a 100 mm (minimum) space from the wall for proper ventilation. 100 mm 100 mm 100 mm...
  • Page 31 Connect the power cord to the monitor and then plug the power cord into the wall outlet. Cautions When Connecting Power Cord 100-240 V ~ • When connecting to a power source, make sure to use the power cord provided with the product and connect with a grounded power outlet.

  • Page 32: Adjusting The Angle

    Adjusting the Angle WARNING Place the monitor mounted on the stand base in an upright position. • When you adjust the angle, do not hold the stand as shown on the following illustration. You may Adjust the angle of the screen. The angle of the screen can be adjusted forward or backward for a injure your fingers.

  • Page 33: Adjusting The Stand Length

    Adjusting the Stand Length WARNING Place the monitor mounted on the stand base in an upright position. Be sure to use both hands when adjusting the monitor. • To avoid injury to your fingers, do not put your hands between the screen and the stand base when adjusting the screen's height.

  • Page 34: Pivot Feature

    Pivot Feature Raise the monitor up to the maximum height. The pivot feature allows the monitor to rotate 90 degrees clockwise or counter-clockwise. Head Stand Adjust the angle of the monitor in the direction of the arrow as shown in the figure. WARNING •...
  • Page 35 Rotate the monitor clockwise or counter-clockwise as shown in the figure. NOTE • An image displayed on the monitor's screen does not rotate according to the screen orientation. • You can rotate the screen easily using the screen pivot shortcut key provided in the Windows operating system.

  • Page 36: Using The Kensington Lock

    Using the Kensington Lock Detaching Stand Body The Kensington security system connector is located at the bottom of the monitor. Place the screen face down. To protect the screen from scratches, cover the surface with a soft cloth. For more information on installation and using this system, refer to the manual supplied with the Press down the button at the bottom-centre on the back of the monitor to detach the stand.

  • Page 37: Installing Wall Mount Plate

    If you use screws longer than the standard length, it may damage the inside of the product. A non-VESA standard screw may damage the product and cause the monitor to fall. LG Electronics is not liable for any accidents relating to the use of non-standard screws.
  • Page 38 Disconnect the power cord first, and then move or install the monitor. There is risk of electric shock. • Installing the monitor on the ceiling or on a slanted wall may result in the monitor falling off, which could lead to injury. Use an authorized LG wall mount and contact the local dealership or qualified personnel.

  • Page 39: Using The Monitor

    USING THE MONITOR DVI-D Connection Transmits the digital video signal from your PC to the Monitor set. Connect the PC and the monitor with the DVI cable as shown in the following illustrations. Connecting to PC • This monitor supports the *Plug and Play feature. * Plug and Play: A feature that allows you to add a device to your computer without the need for physical device configuration or user intervention.

  • Page 40: Hdmi Connection

    HDMI Connection DisplayPort Connection Transmits digital video and audio signals from your PC to the monitor. Connect your PC to the monitor Transmits the PC's digital video and audio signals to the monitor. Connect your PC to the monitor using using the HDMI cable as shown in the illustration below.

  • Page 41: Connecting Av Devices

    Connecting AV Devices Connecting Peripherals HDMI Connection USB Cable-PC Connection Transmits digital video and audio signals from your AV device to the monitor. Connect the AV device and The USB port has hub functionality. the monitor with the HDMI cable as shown in the following illustrations. To use USB 3.0, connect the A-B type USB 3.0 cable to the PC.
  • Page 42 NOTE • Make sure to install the most recent Window OS service pack before using the product. • Peripheral devices and cables are sold separately. • A keyboard, mouse, or USB storage device can be connected to the USB port. CAUTION Cautions When Using a USB Storage Device •...

  • Page 43: User Settings

    USER SETTINGS Activating the Quick Menu Press the to display the OSD Quick Menu. Press or button on the front to go through the menu options. Press , or [ ] button to set your options. / ] or select Exit. If you wish to exit the OSD Quick Menu, press [ Exit : Ok...
  • Page 44 The applicable setting options are as shown below. Quick Menu Explanation Exit Closes the Quick Menu. Input Selects the applicable input mode. Picture Mode Selects the Picture Mode. NOTE If Picture Mode is not the Custom mode, Gamma and Color Temp will not be activated. •...

  • Page 45: Quick Settings

    Quick Settings Press the button on the front of the monitor, then select All Settings to display the complete OSD menu. Press , , or button on the front to select Quick Settings. Quick Settings Configure the options following the instructions that appear in the bottom right corner. Brightness 100 >...

  • Page 46: Quick Settings

    The applicable setting options are as shown below. All Settings > Explanation Quick Settings Brightness Adjusts the brightness of the screen. NOTE • Press the button to toggle between Turn on 'Brightness Stabilization' / Turn off 'Brightness Stabilization'. • When Brightness Stabilization is On, the Brightness adjustment function is deactivated. When Brightness Stabilization is On, SMART ENERGY SAVING and DFC functions are deactivated.

  • Page 47: Input

    Input Press the button on the front of the monitor, then select All Settings to display the complete OSD menu. Press , , or button on the front to select Input. Input Configure the options following the instructions that appear in the bottom right corner. If you want to configure an upper menu or another option, move using the button among the front adjust buttons or by pressing / ].
  • Page 48 The applicable setting options are as shown below. All Settings > Input Explanation Input List Selects the input mode. Aspect Ratio Adjusts the aspect ratio of the screen. (Full Wide, Original, 1:1) NOTE • The display may look the same for Full Wide, Original, and 1:1 options at the recommended resolution (1280 x 1024). Full Wide Displays the video to fit the screen, regardless of the video signal input.

  • Page 49: Picture

    Picture Press the button on the front of the monitor, then select All Settings to display the complete OSD menu. Press , , or button on the front to select Picture. Picture Configure the options following the instructions that appear in the bottom right corner. Picture Mode Custom >...
  • Page 50 The applicable setting options are as shown below. All Settings > Picture Explanation Custom Allows the user to adjust each element. The colour mode of the main menu can be adjusted. Picture Mode Mono Mono (black and white) colour mode. Reader Optimizes the screen for browsing documents.
  • Page 51 All Settings > Picture Explanation Picture Adjust Brightness Adjusts the brightness of the screen. NOTE • Press the button to toggle between Turn on 'Brightness Stabilization' / Turn off 'Brightness Stabilization'. • When Brightness Stabilization is On, the Brightness adjustment function is deactivated. When Brightness Stabilization is On, SMART ENERGY SAVING and DFC functions are deactivated.
  • Page 52 All Settings > Picture Explanation Picture Adjust Adjusts the brightness automatically according to the screen. Disables the DFC feature. Response Time Sets a response time for displayed pictures based on the movement of the picture on the screen. For a normal environment, it is recommended that you use Fast. When there is a lot of motion, it is recommended that you use Faster. Setting to Faster may cause image sticking.
  • Page 53 All Settings > Picture Explanation Color Adjust Gamma Set your own gamma value. Gamma 1.8, Gamma 2.0, Gamma 2.2, Gamma 2.4, Gamma 2.6, DICOM Gamma Curve. The higher the gamma value, the darker the image becomes. Likewise, the lower the gamma value, the lighter the image becomes. Color Temp Set your own colour temperature.

  • Page 54: General

    General Press the button on the front of the monitor, then select All Settings to display the complete OSD menu. Press , , or button on the front to select General. General Configure the options following the instructions that appear in the bottom right corner. Language English >...
  • Page 55 The applicable setting options are as shown below. All Settings > General Explanation Language Sets the menu screen to the desired language. SMART ENERGY SAVING Conserve energy by using luminance compensation algorithm. High Saves energy using the high-efficiency SMART ENERGY SAVING feature. Saves energy using the low-efficiency SMART ENERGY SAVING feature.

  • Page 56: Quick Settings

    All Settings > General Explanation DisplayPort 1.2 Enables or disables DisplayPort 1.2. NOTE Be sure to configure this option according to the DisplayPort version supported by your graphics card. Set this option to Disable if your graphics card does not support DisplayPort 1.2. •...

  • Page 57: Auto Configuration

    Auto Configuration Press the button on the front of the monitor, then select All Settings to display the complete OSD menu. Press , , or button on the front to select Auto Configuration. Auto Configuration Configure the options following the instructions that appear in the bottom right corner. Do you want to Auto Configuration? If you want to configure an upper menu or another option, move using the button among the front adjust buttons or by pressing / ].

  • Page 58: Troubleshooting

    TROUBLESHOOTING Nothing is displayed on the screen. Is the monitor's power cord plugged in? • Check if the power cord is correctly plugged into the power outlet. Is the power indicator on? • Check the power cable connection and turn on the power switch. Is the power indicator displaying as green? •...
  • Page 59 NOTE • Vertical Frequency: In order to display an image, the screen must be refreshed dozens of times per second, like a fluorescent lamp. The number of times the screen is refreshed per second is called vertical frequency, or refresh rate, and is represented by Hz. •...
  • Page 60 The 'Unknown Monitor' message appears when the monitor is connected. Did you install the monitor driver? • Install the enclosed monitor driver which is provided with the monitor or go to LG Electronics homepage ( www.lg.com ) to download and install the monitor driver. •...

  • Page 61: Product Specifications

    PRODUCT SPECIFICATIONS Horizontal Vertical Polarity Specifications are subject to change without notice. Preset Mode Frequency Remarks Frequency (Hz) (H/V) (kHz) Preset Mode 640 x 480 31.469 59.94 720 x 400 31.469 70.087 800 x 600 37.879 60.317 D-SUB 1024 x 768 48.363 60.004 Horizontal...

  • Page 62: Input Timing (Video)

    Power Indicator Vertical Mode LED Colour Horizontal Polarity Preset Mode Frequency Remarks On Mode Green Frequency (kHz) (H/V) (Hz) Power Saving Mode 640 x 480 31.469 59.94 Off Mode 720 x 400 31.469 70.087 800 x 600 37.879 60.317 1024 x 768 48.363 60.004 1152 x 864...
  • Page 63 Read the user manual (CD) carefully and keep it at hand. The product label contains necessary information for LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing after-service.

Table of Contents