Related Manuals for Philips CM-150 CA
Summary of Contents for Philips CM-150 CA
- Page 1 CM-150 CA Control module for large scale architectural and media applications using Flex nodes...
- Page 2 CM-150 CA delivers integrated data and power to Flex LED luminaires from Philips Color Kinetics. With multiple mounting options, CM-150 CA is the single solution for all large scale installations using Flex nodes, whether color or white. An integrated test button instantly confirms proper functioning of your devices, eliminating costly and time-consuming reinstallation.
- Page 3 Fuse (2) 5 A, fast-blow fuses (2) 4 A, fast-blow fuses Philips Color Kinetics full range of controllers, including Light Data Input Source System Manager, Video System Manager Pro, iPlayer 3, Antumbra iColor Keypad, and ColorDial Pro, or third-party controllers.
- Page 4 Fuse (2) 5 A, fast-blow fuses (2) 4 A, fast-blow fuses Philips Color Kinetics full range of controllers, including Light Data Input Source System Manager, Video System Manager Pro, iPlayer 3, Antumbra iColor Keypad, and ColorDial Pro, or third-party controllers.
-
Page 5: Product Selection
Product Selection To order a complete CM-150 CA, choose a mounting type (DIN Rail Mount or Surface Mount), 3-wire or 4-wire output, a voltage that matches your Flex nodes (7.5/12 V or 24 V), any necessary accessories (such as leader cables). -
Page 6: Power Supplies
Control Module and Leader Cables CM-150 CA is part of a complete system which includes the control module and: • One or more third-party power supplies • One leader cable to attach each Flex strand to a control module port •... -
Page 7: Plan The Installation
Refer to the CM-150 CA Installation Instructions for specific warning and caution maintain, and operate CM-150 CA in such a manner as to comply with all applicable statements at www.colorkinetics.com/ls/pds/ codes, state and local laws, ordinances, and regulations. Consult with the appropriate cm150ca/. - Page 8 CM-150 CA. eW Flex Micro 75 nodes 150 nodes CM-150 CA must be installed in a location that allows air to move freely around the iColor Flex LMX gen2 75 nodes 150 nodes device. Startup and operating temperatures are rated to 50 °C (122 °F). Exceeding...
- Page 9 Surface Mount or DIN Rail Mount? CM-150 CA is available in either a Surface Mount or a DIN Rail Mount form factor. The DIN Rail Mount form factor is suitable for dry locations only. It can be used indoors, or it can be mounted in a suitable outdoor enclosure.
- Page 10 Position and Mount CM-150 CA Make sure the power is OFF before mounting and connecting CM-150 CA. 1. Each CM-150 CA is identified by a unique serial number and IP address. The Included in the box, DIN Rail Mount serial number and default IP addresses are located on a label on the CM-150 CA housing.
- Page 11 Surface Mount Installation 1. Run Cat. 5e or better cable from the data output port of a Philips Color Kinetics Ethernet controller, such as Light System Manager or Video System Manager Pro. 2. If necessary, cut the cable jacket to expose the wire pairs. Do not strip the wire pairs.
- Page 12 Ethernet devices without a repeater. 100 m (328 ft) Max 100 m (328 ft) Max 1. Cut a sufficient length of Cat. 5e or better cable to connect the first CM-150 CA Ethernet maximum data cable length device in a series with the next.
- Page 13 6. While holding the wires firmly in place, push down on the pivot connectors until they click shut. 7. Run the free end of the cable to the next CM-150 CA device in the series, and make Ethernet data input connections as described in the previous section.
- Page 14 1. Strip 5 mm (0.2 in) of insulation from the wires. If using stranded wire, twist each wire tight to secure the wire threads. 2. Run the DC power cable through the bottom of the CM-150 CA housing. Pull at least 127 mm (5 in) of wire into the housing.
- Page 15 152 mm (6 in) to 3.7 m (12 ft) distance from the connector to the first node. Surface Mount Installation 1. Remove the end caps. 2. Plug leader cable or the Flex strand into the CM-150 CA, and secure the connection. 4-wire output 3-wire output DIN Rail Mount Installation 1.
-
Page 16: Secure Cover
CM-150 CA devices using QuickPlay Pro with a computer connected to your lighting network. When a CM-150 CA device is connected to your lighting network, the CM-150 CA tab under PDS Configuration becomes active. For details on standard QuickPlay... - Page 17 CA devices. Select a device from the Controllers list. 2. If necessary, select a CM-150 CA device from the Controllers list. The firmware version for the selected CM-150 CA device appears at the top of the QuickPlay Pro window, on the right.
- Page 18 You must successfully re-install the firmware image to restore normal CM-150 CA operations. • In the case of power loss or interruption, the CM-150 CA device retains its assigned IP address, but you are temporarily unable to communicate with the device using that address.
-
Page 19: Replacing Fuses
Replacing Fuses CM-150 CA fuse types CM-150 CA has two fuses, each of which protects a Flex strand from excessive current. Two extra fuses are included in with all DIN rail mountable Control module Fuse type CM-150 CA devices. CM-150 CA, 24V... - Page 20 Copyright © 2017 Philips Lighting Holding B.V. All rights reserved. Chromacore, Chromasic, CK, the CK logo, Color Kinetics, the Color Kinetics logo, ColorBlast, ColorBlaze, ColorBurst, ColorGraze, ColorPlay, ColorReach, iW Reach, eW Reach, DIMand, EssentialWhite, EvenBalance, eW, iColor, iColor Cove, IntelliWhite, iW, iPlayer, Optibin, and Powercore are either registered trademarks or trademarks of Philips Lighting Holding B.V.