Table of Contents
Quick Links
PJ-Net Organizer
OWNERʼS MANUAL
PJ-Net Organizer
Model No. POA-LN01
Preparation
Installation
Basic Setting and Operation
Controlling the Monitor
Serial Port Use
Appendix
INSTALLATION and OPERATION of the PJ-
Net Organizer
This PJ-Net Organizer is an optional product to control
and set up a monitor via a network. Attach this product
to the monitor and connect a network cable. By
accessing the connected monitor using the web brows-
er on your computer, the monitor can be controlled and
set up remotely.
This product is only used for Monitors that
have a terminal for the PJ-Net Organizer.
This manual explains the installation of the PJ-Net
Organizer and its operation.
Table of Contents
Related Manuals for Sanyo PJ-Net POA-LN01
Summary of Contents for Sanyo PJ-Net POA-LN01
- Page 1 PJ-Net Organizer OWNERʼS MANUAL PJ-Net Organizer Model No. POA-LN01 Preparation Installation Basic Setting and Operation Controlling the Monitor Serial Port Use Appendix INSTALLATION and OPERATION of the PJ- Net Organizer This PJ-Net Organizer is an optional product to control and set up a monitor via a network. Attach this product to the monitor and connect a network cable.
-
Page 2: Federal Communication Commission Notice
Model Numbers : POA-LN01 Trade Name : Sanyo Responsible party : SANYO FISHER COMPANY Address : 21605 Plummer Street, Chatsworth, California 91311 Telephone No. : (818)998-7322 Trademark Ethernet is a registered trademark of Xerox Corporation. Microsoft, Windows, are registered trademarks of Microsoft Corporation. -
Page 3: Use Of This Manual
It may cause fire or an accident depending on the change of environment. SANYO Electric Co. Ltd assumes no responsibility for the loss or damage of data or damage of the computer caused by use of this product. -
Page 4: Table Of Contents
Contents Features ....... . .5 Recommended Operating Environment ..6 1 Installation . -
Page 5: Features
Preparation Features Web Management function With this function, you can watch monitor functions such as power status, input mode, sig- nal condition, monitor-use time, etc. through the network by using the web browser installed on your computer. Power ON ! E-Mail Alert function Monitor (PJ-Net Organizer) sends messages to the registered e-mail addresses when a power failure occurs with the monitor. -
Page 6: Recommended Operating Environment
Preparation Recommended Operating Environment To perform the management and setting up the monitor using this product, the environ- ment described below is required. Operating System Web Browser* Plug-Ins Computer Environment Network Environment Internet Mailer* The limitation of connection between this product and Hub or Computer Suitable LAN cables are limited by length and type as follows;... -
Page 7: Installation
Installation... -
Page 8: Flow Of Installation
Installation Flow of installation The following are instructions for attaching this product to the monitor and connecting it to the network. Please review the entire procedure to become familiar with it. Check package Please check the contents of a package. This product contains a network board, and an ownerʼs manual (this manual). -
Page 9: Name And Function Of Each Part
Name and function of each part Network Board Power indicator This illuminates red when the network board is mounted onto the monitor and the AC plug is connected . Serial port Connecting the Serial cable. LAN port Connecting the LAN cable. Monitor (Rear Terminal of Monitor) Input port... -
Page 10: Mounting
Installation [1] Mounting Disconnect the AC plug from the monitor. Remove the screws on the back of the cabi- net, and then remove the terminal covers. Insert the network board into the monitor, and fix it with the screws. Caution ✐... - Page 11 Set the Option Switch from the UP position to the DOWN position. Cannot use the serial port of the monitor ✐ in this position. Set back to the UP position when the network board is not used. SERIAL PORT Organizer VIDEO-IN VIDEO-OUT Down...
-
Page 12: Connection Of Lan Cable
Installation [2] Connection of LAN cable To connect to the network, it is required to use the UTP (Unshielded Twisted Pair) straight cable with RJ-45 plug. There are two different types of cables depending on whether the network is constructed with 10Base-T or 100Base-TX. Prepare the Hub (10Base-T or 100Base-TX) to distribute the network cable. -
Page 13: Network Configuration
[3] Network configuration When you connect a monitor to a network, the network number of monitor must be the same as the network you intend to connect. You should configure monitorʼs network first. Make sure that the monitor is connected to the network correctly. To configure the network, use the computer. -
Page 14: Configure The Network With The Computer
Installation Configure the network with the computer This example explains how to set the following configuration. IP Address : 172.21.95.224 Subnet Mask : 255.255.255.0 Default Gateway : 172.21.95.1 : 172.21.1.53 The default network configuration is set as follows. IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0... -
Page 15: Completing Of Installation
Configure the network of the monitor by using the web browser. . Enter the IP address of the monitor as the URL. The login page will be displayed and login. For further information, please see chapter “2: Basic Setting and Operation” on page 21. -
Page 16: Flash Player
Installation Flash Player The Flash Player version 9 or later is required when you control the monitor. If your computer does not have, follow to the message on the control page to install the Flash Player. For further product information or installing, see the homepage. -
Page 17: Configure The Network Of Computer
Installation Configure the network of computer When you use the monitor through the network, the IP address of the monitor must have the same IP network number of the existing network. Also it is required to use the same IP network number of the computer to set up the monitor. In the network included with the gateway (router), it must be used with the IP network number specified by the gateway (router). -
Page 18: Windows Xp
Windows XP This example explains how to set the following network address. IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Gateway Address : 192.168.0.1 Select the Control Panel menu from the [Start] menu. Click the Network and Internet Connection and then click the Network on the control panel. -
Page 19: Notice About System Construction
Installation Notice about system construction In case of installing the monitor with PJ-Net Organizer into the network constructed with the DHCP/BOOTP server. This PJ-Net Organizer does not support the DHCP/BOOTP server. The static IP address must be configured by the manual. To use this product in this network environment, set it up so that the DHCP/BOOTP server does not assign the IP address configured to this product for another device on the network. - Page 20 Note...
-
Page 21: Basic Setting And Operation
Basic Setting and Operation... -
Page 22: Login The Setting Page Of The Monitor
Basic Setting and Operation This chapter describes basic operations and settings for controlling the monitor via a net- work using this product. It is required that computer and monitor are connected to the net- work and the network address be properly configured. Login the setting page of the monitor Enter the IP address Launch the web browser installed in your... -
Page 23: Display Of Setting Page
Display of setting page The following setting page of the monitor is displayed. Perform the various kinds of set- ting through this page. Press a button of Main Menu to display the control or setting page. ☛ The main menu which can be set up and control the monitor appears on the lower side of the page. -
Page 24: Initial Settings
Basic Setting and Operation Initial Settings After installing this product onto the monitor, perform the following basic initial setting. Press the Initial Setting button on the main menu to display the initial setting page. The password can be set in this page. Password Setting This page is to set the password to restrict the access from an unauthorized person through the network. -
Page 25: Network Configuration
Network Configuration Press the Network Setting button on the main menu. The following setting page is dis- played. This page is to set the IP Address, Subnet Mask, Default gateway, DNS (Domain Name Server) and Model ID. Configure the network The IP address and Subnet Mask have been configured already in chapter “1: Installation”... -
Page 26: E-Mail Setting
Basic Setting and Operation E-mail Setting This product has an E-mail function which can send an alert message to users or an administrator if it detects an abnormality on the monitor or when the panel usage time reaches to setting time. Press the E-Mail Setting button on the main menu and follow the below steps. -
Page 27: Mail Check And Delete
Mail Check and Delete Select "Mail Check and Delete" of sub menu. The registered address is displayed as the "Mail To" address. To delete the registered address, check the box and press the Delete button. Option (Condition selection for sending alert message) Select "Option"... -
Page 28: Examples: Type And Contents Of Alert Mail
Basic Setting and Operation Examples: Type and contents of alert mail When the monitor has an abnormality, the following alert messages are sent to the regis- tered E-mail address according to your selected condition. Administrator or user can take an efficient action quickly by receiving this massage. This is very useful to maintain and service the monitor. -
Page 29: Snmp Setting
SNMP Setting This product can be used for SNMP (Simple Network Management Protocol) function. Press the SNMP Setting button on the main menu and follow the below steps. LCD Information (Setting SNMP Agent) Select "Information" of sub menu, type the MIB of SNMP agent (A contact name and a place of this product) or a community name (reference or setting) and press the Set button for setting. -
Page 30: Trap Check And Delete
Basic Setting and Operation Trap Check and Delete Select "Trap Check and Delete" of sub menu. The registered trap is displayed. To delete it, check the box and press the Delete button. Trap Option (Selection for sending alert message) Select "Trap Option" of sub menu.Type the panel usage time that you want to set, and check the condition items under which alert messages will be sent and press the Set button. -
Page 31: Controlling The Monitor
Controlling the Monitor... -
Page 32: Check The Status Of Monitor
Controlling the Monitor Check the status of monitor In the "Status" page, you can check the status of the monitor as follows: Status 1 Power: Condition of Power Power ON / Power Error / Power OFF Input: Input Mode AV1 / RGB / AV2 RGBHV / AV2 YPbPr / AV3 / HDMI / PC Video Signal: Availability of Input Signal Yes / No Panel Usage: Accumulated Panel-use Time... -
Page 33: Status 2
Status 2 Child Lock: Key Lock of Monitor RC Inhibition: Button Lock of Remote Control Power save: The monitor turns into power save mode, after 1 minute with no signal. OFF (Unlock) / On OFF (Unlock) / On Off/On Check the status of monitor... -
Page 34: Control The Monitor
Controlling the Monitor Control the monitor Press the Control button on the main menu. The sub menu for controlling the monitor will be displayed on the upper side of the page. When you click each control item, the control page is displayed according to the sub menu you selected. ✐... -
Page 35: Input
Input Click the Input on the sub menu. The control page will be displayed. Select an input source with radio button and press the Set button to change the input source. Wide Mode Click the Wide Mode on the sub menu. The control page will be displayed. Select a wide mode with radio button and press the Set button to change the wide mode. -
Page 36: Other 1
Other 1 Click the Other 1 on the sub menu. The control page will be displayed. Select the item of Child Lock, RC Inhibition, or Power save with radio button and press the Set button to change these functions. The Child Lock, RC Inhibition, or Power save can be selected independently. ✐... -
Page 37: Make A Memo
Controlling the Monitor Make a memo This function can be used as a memo. Press the Memo button on the main menu. The fol- lowing setting page will be displayed. Press the Save button to memorize. The maximum 127 characters can be typed. ✐... - Page 38 Note...
-
Page 39: Serial Port Use
Serial Port Use... -
Page 40: Example Of Connection
Serial Port Use This Network Board provides with a serial control port (RS232C) to control the monitor. Example of Connection Control the monitor through network and serial control function. Specification and Setting of RS232C Terminal Terminal : HDB9-PIN Pin Configuration No Connect No Connect R x D... -
Page 41: Command For Controlling The Monitor
Command for controlling the monitor The below commands for controlling the monitor can be used. PSAVE PSAVE Serial Port Use EXAMPLE : POWER ON (C00) FUNCTION CODE / END CODE 43h 30h 30h 0Dh 0Ah ASCII '0' [CR] [LF]... -
Page 42: How To Set Network Congiguration On Network Board To Default
Serial Port Use If you forgot current network configuration, (IP address, subnet mask,password DNS, and default gateway), you can set them to default value via the serial port (RS232C). How to set Network configuration on network board to default Send below command (ASCII) to network board W_DEFAULT + [CR] Network board will be rebooted. -
Page 43: Appendix
Appendix... -
Page 44: Examples Of Connection
Appendix Examples of Connection Direct connection Connect the monitor (LCD01) to the control computer (PC05) directly. Monitor Name: LCD01 IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 : 0.0.0.0 Connect the monitor (LCD01) to the control computer (PC05) via the hub. Monitor Name: LCD01 IP Address : 192.168.0.2... -
Page 45: The Gateway (Router) Installed In The Network
The gateway (Router) installed in the network Connect the monitor (LCD01) to the control computer (PC05) via the gateway. Meeting Room Monitor Name: LCD01 IP Address : 192.168.200.15 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.200.1 : 192.201.1.5 Network Group: 192.168.200.0 To another network Office Computer Name: PC05... -
Page 46: Web Browser Setting
Appendix Web browser setting This product is designed to enable the monitor to be set up and controlled from an Internet web browser. Depending on the preference settings of the web browser, some control functions may not be available. Please make sure that the following functions are set up properly in the web browser. -
Page 47: Examples: Os/Browsers
Web browser setting Examples: OS/Browsers Windows XP Professional Internet Explorer v.6.0 ActiveScript setting Select the Internet Options menu from the Tool menu on the web browser and then select Security tab and click Customize Level… button. On the security setting window, scroll down and find the Scripting item, make sure that “Enable”... - Page 48 Appendix Proxy setting Select the Internet Options menu from the Tool menu on the web browser and then select Connection tab and click LAN Settings button. Properly set up your web browser's the proxy server settings according to the local area network environment to which the monitor is connected.
-
Page 49: Product Specification
Product specification Type ...Pj-Net Organizer LAN interface ...Applicant regulation IEEE802.3 (10Base-T) Network protocol Serial interface Power source ...Supplied from the LCD monitor Power consumption ...3.0 watts Dimensions (W x H x D)...4.2” x 1.4” x 5.3” (107 x 34.9 x 135mm) Weight ...0.92 lbs (420 g) Operating temperature ...41˚F ~ 95 ˚F (5˚C ~ 35 ˚C) Storage temperature ...14˚F ~ 140˚F (-10˚C ~ 60˚C) -
Page 50: Port Specification
Appendix Port Specification LAN port specification 8-pin modular connector (RJ-45) 1 2 3 4 5 6 7 8 pin No. MAC Address The MAC address is indicated on the rating label. NOTES ON Lithium Battery (CALIFORNIA USA ONLY) This product uses a Lithium Battery which contains Perchlorate Material - special han - dling may apply. - Page 51 Note...
- Page 52 Printed in Japan Part No. 610 333 5582 (1AA6P1P5387-- IFFNA)