Table of Contents
Table of Contents
Related Manuals for Makita EG2250A
Summary of Contents for Makita EG2250A
- Page 1 EG2250A GB Petrol Generator Instructions for Use EG2850A F Groupe Electrogène EG4550A Manuel d'instructions EG5550A D Generator Betriebsanleitung EG6050A Generatore a benzina Istruzioni per l’utilizzo NL Gebruiksaanwijzing Benzinegenerator E Generador a gasolina Manual de instrucciones...
- Page 2 EG2250A EG2850A EG4550A, EG5550A, EG6050A...
-
Page 6: About Safety
All information and specifications included in this These signal words mean: publication were based on the latest production information at the time of approval for printing. Makita DANGER: Corporation reserves the right, however, to discontinue or Indicates that loss of life, severe personal injury or... -
Page 7: Generator Safety
• If the generator is stored outdoors and is unprotected from the weather, check all of the electrical Makita generators are designed to give safe and components on the control panel before each use. dependable service if operated according to instructions. - Page 8 S (START): Starts the engine by operating the starter hazards of personal injury. motor. • Do not modify parts which may increase or decrease *EG2250A and EG2850A equipped with I (ON)/O (OFF) the governed speed. switch only • Only use extension cords that are grounded and are a Starter Grip (Fig.
-
Page 9: Generator Use
Do not exceed the current limit specified for any one Ground System receptacle. If an overloaded circuit causes the AC circuit Makita portable generators are equipped with a system breaker or AC circuit protector to turn off, reduce the ground that connects generator frame components to the... -
Page 10: Pre-Operation Checks
Check Engine Fuel (Fig. 14) circuit protector continues to go off, discontinue charging With the engine stopped, check the fuel level gauge. Refill and consult your authorized Makita generator dealer. the fuel tank if the fuel level is low. Disconnecting the battery cables: WARNING: 1. -
Page 11: Starting/Stopping The Engine
Doing so can cause professionals and are normally performed by a Makita overheating and/or damage the generator. In order to technician or other qualified mechanic. -
Page 12: Safety Precautions
Operate outside away from open windows or To ensure the best quality and reliability, use only new, doors. genuine Makita parts or their equivalents for repair or - Burns from hot parts. replacement. Let the engine and exhaust system cool before touching. -
Page 13: Fuel Sediment Cup Cleaning
NOTICE: NOTICE: Operating the engine without an air filter, with a damaged If the spark plug is loose, it can overheat and damage the air filter, or with an improperly installed air filter will allow engine. dirt to enter the engine, causing rapid engine wear. This If the spark plug is over tightened, it can damage the type of damage is not covered by the Distributor’s Limited threads in the cylinder head. -
Page 14: Storage Precautions
*Use gasoline stabilizers that are formulated to extend storage life. Follow the manufacturer’s instructions for use. Contact our authorized Makita generator dealer for stabilizer recommendations. Draining the Fuel Tank and Carburetor Select a well ventilated storage area away from furnaces, water heaters, or clothes dryer, or any other appliance (Fig. -
Page 15: Troubleshooting
• Black exhaust smoke or high fuel consumption. take the generator to an authorized Makita Replacement Parts generator dealer. The emission control systems on your Makita engine were Check if the If there are defects: designed, built, and certified to conform to applicable electrical - Replace the electrical emission regulations. -
Page 16: Wiring Diagram
Class 2 Mutual Inductor Stud Main Coil Drive Coil 8A Overcurrent Protective Device Oil Level Flameout Rotor Coil Direct- current Winding Engine Engine Oil Spark Ignition Level Switch Plug Coil Note: Wiring is the same for the EG2250A and EG2850A. - Page 17 Panel Electric Generator 19.5/24/26A Class 1 Overcurrent Protective Device Mutual Inductor 16A Overcurrent Class 2 16A Overcurrent Mutual Inductor Protective Device Protective Device Main Coil Drive Coil 8A Overcurrent Protective Device Oil Level Flameout Rotor Coil Fuel Cut Direct- Charging Coil current Startup...
-
Page 18: Specifications
SPECIFICATIONS MODEL EG2250A EG2850A EG4550A EG5550A EG6050A Type Brush, 2-poles, single phase Voltage regulating system AVR type AC Output 230 - 50 Rated voltage-Frequency V-Hz Rated current 11.3 17.4 21.7 Rated output VA (W) 2,000 2,600 4,000 5,000 5,500 Generator... - Page 19 - Carbon monoxide poisoning from engine • To reduce the possibility of a fire or explosion, be exhaust. careful when working around gasoline or batteries. Use Operate outside away from open windows or only a non-flammable solvent, not gasoline, to clean doors.
-
Page 20: Ec Declaration Of Conformity
TORQUE: 17 - 22 lbf•ft (24 - 29 N•m, 2.4 - 3.0 kgf•m) Designation of Machine: Petrol Generator Model No./ Type: EG2250A, EG2850A, EG4550A, Fit the front stand (Fig. 26) EG5550A, EG6050A 1. Insert an M8×100 bolt into the holes on the rubber Specifications: see "SPECIFICATIONS"... - Page 21 Makita ATTENTION : Corporation se réserve toutefois le droit, d'interrompre ou Signale un risque de blessures corporelles si les de modifier les spécifications ou la conception à...