Quick Links

UB-U01III/U02III/U03II User's Manual
Standards and Approvals
The following standards are applied only to the boards
that are so labeled. (EMC is tested using the EPSON
power supplies and TM series printers.)
Europe:
CE marking
North America: FCC/ICES-003 Class A
Japan:
VCCI Class A
Oceania:
AS/NZS CISPR22 Class A
WARNING
This is a Class A product. In a domestic environment
this product may cause radio interference, in which
case the user may be required to take adequate
measures.
The printers in which this board is installed becomes
class A devices.
The connection of a non-shielded printer interface cable
to this board will invalidate the EMC standards of this
device. You are cautioned that changes or
modifications not expressly approved by Seiko Epson
Corporation could void your authority to operate the
equipment.
CE Marking
The printer conforms to the following Directives and
Norms:
Directive 2004/108/EC
EN 55022 Class A
EN 55024
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
Before Using
Be sure to read this manual carefully for effective and correct use of the
product and store it in accessible location.
Key to Symbol
The symbol in this manual is defined below. Read the following carefully
before handling the product.
CAUTION:
Observe cautions to avoid minor injury to yourself or damage to your
equipment.
FCC Compliance Statement
For American Users
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely
to cause harmful interference, in which case the user will
be required to correct the interference at his own expense.
For Canadian Users
This Class A digital apparatus complies with Canadian
ICES-003.
À l'intention des utilisateurs
canadiens
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-11
1
Copyright 2003 by Seiko Epson Corporation
English
Printed in China
loading

Summary of Contents for Epson UB-U01III

  • Page 1 Printed in China Standards and Approvals FCC Compliance Statement The following standards are applied only to the boards that are so labeled. (EMC is tested using the EPSON For American Users power supplies and TM series printers.) Europe: CE marking...
  • Page 2 Software: You need a device driver when you use the product. Please ask your dealer how to get the device driver for the UB-U01III/ U02III/U03II and how to install it. Note: Even if the above operation environments are satisfied, your system may not work properly, depending on the devices connected to your system.
  • Page 3: Display Module

    USB cable connector (USB HUB: UB-U01III only) Insert the square connector end of the USB cable into the upstream connector of the UB-Board. Insert the opposite end of the USB cable into the downstream connector of the host computer.
  • Page 4 CAUTION: Do not connect any device other than the EPSON display module connector to the DM connector. Also, do not connect other lines, such as a telephone line, to the DM connector; otherwise the printer and other lines may be damaged.
  • Page 5 と電波妨害を引き起こすことがあります。 この場合には使用者が適切な対策を講ずるよう要求されることがあります。 VCCI-A はじめに ® 本製品は、EPSON TM プリンター用に開発された、USB インターフェイスボー ドです。 ❏ UB-U01III /U02III を装着すると、 TM プリンター本体側のディスプレイモ ジュールコネクター(DM コネクター)は使用できなくなります。DM コネ クターを使用する場合は、UB-U01III /U02III の DM コネクターを使用し てください。 ❏ UB-U01III のハブはバス電源ハブです。したがって、ここにバス電源ハブ (UB-U01III 含む )、または消費電流 100mA を超えるバス電源ファンク ションを直接接続することはできません。(UB-U01III のハブに UB- U02III 及び UB-U03II を直接接続することは可能です。)
  • Page 6 OS: Windows 98 以降 (Second Edition を推奨 ) その他の OS につきましては、ハードウェアをお買い求め頂いた販売店に お問い合わせください。 ❏ ソフトウェア: 本製品を使用するには、デバイスドライバーが必要となります。デバイ スドライバーの入手方法、及びインストール手順につきましては、ハー ドウェアをお買い求め頂いた販売店にお問い合わせください。 注記: 上記の動作環境を満たした場合でも、機器の組み合わせによっては正常に動 作しない場合があります。 同梱品 本製品の同梱品は次の通りです。万一、梱包品の不足や不良がございました ら、お買い求めいただきました販売店までご連絡ください。また、フェライ トコアとロッキングワイヤサドルは、< > 内の部品番号で別途ご購入頂けま す。 ❏ 本製品 (UB-U01III/U02III/U03II) ❏ 本書 ❏ フェライトコア <2031678> ❏ ロッキングワイヤサドル ・ UB-U01III/U02III 用 <1061268> ・ UB-U03II 用 <1091047>...
  • Page 7 DM 用コネクター (UB-U01III/ USB アップスト U02III のみ) リームコネクター ロッキングワイ USB ダウンスト ヤサドル リームコネクター (USB HUB: UB- U01III のみ) USB ケーブル 3. UB-U01III/U02III/U03II アップストリームコネクターに、USB ケーブル の角型のコネクターを差し込みます。 4. ホストコンピューターのダウンストリームコネクターに、USB ケーブル の平型のコネクターを差し込みます。 5. プリンターの設定をパラレルインターフェイス設定にし、#31 ピンリ セット信号も設置可能な機種については、 「使用する」に設定してくださ い。詳細はプリンターのマニュアルのパラレルインターフェイスの設定 を参照してください。 6. UB-U01III/U02III/U03II 用デバイスドライバーをインストールします。 インストール手順は、ハードウェアをお買い求め頂いた販売店にお問い 合わせください。...
  • Page 8 日本語 ディスプレイモジュール ディスプレイモジュールを取り付ける場合は、以下の設定にしてください。 項目 選択 通信設定 通信速度 19200 bps パリティー なし データ長 8 ビット 「デバイスの選択」の初期設定(変更 「ディスプレイのみ」 可能な一部の機種のみ) 「接続形態設定」 「Y 接続無効」 (変更可能な一部の機種のみ) 設定方法の詳細については、接続するディスプレイモジュールのマニュアル をご覧ください。また、以下の点にご注意ください。 注意: ・DM 用コネクターに弊社のディスプレイモジュールコネクター以外は接続し ないでください。また、DM 用コネクターには電話回線等を接続しないでく ださい。プリンターおよび電話回線等の故障の原因になります。 ・EMI 規格を満たすため、フェライトコアは必ず取り付けてください。 フェライトコアは、図のように、ディスプレイモジュールのケーブルをフェ ライトコアで挟んで取り付けます。 ディスプレイモジュール フェライトコア...

This manual is also suitable for:

Ub-u02iiiUb-u03ii