Quick Links
RF Pairing with STB
Remote Control User
Guide
Method of pairing:
1. Press and hold Setup Key until
LED indicator blinks twice.
2. Press and hold Info Key, till STB
display 3 random digits on TV
screen, LED indicator turn on.
3. Entering the 3 random digits
numeric displayed on TV screen
to pair remote control with target
STB. For each digit key press,
when the key released, LED
indicator acts a reverse blink.
4. The LED indicator blinks twice
once the Remote Control Pairing
with the target successfully.
Otherwise if pairing
unsuccessfully the remote blink 5
times and return to user mode.
Notes:
In Step 4, STB will display 3
random digits on TV screen, user
need press first digit within 8
second. For second and third
Huawei RC2843002/01
digits, user has to press the digit
within 4 second.
If timeout occurs, the LED
indicator blinks 5 times and
returns to user mode.
User also can interrupt the pairing
during Validation Process by
pressing Info key.
Installing Batteries
If pairing is interrupted by pressing
Info Key, or pairing failed, the
The remote control requires 2 AAA
LED indicator blinks 5 times, and
size (1.5V) batteries.
returns to user mode.
1. On the back of the remote, press
the battery cover tab, lift and
Programming to control TV
remove the battery cover.
device
2. Insert 2 AAA-size batteries,
matching the (+) and (–) symbols
There are two ways to do this. If
shown on the battery
your device is listed in the Code List
compartment.
at the end of this Manual, you can
3. Put back the battery cover. Test
use section A. If your device is not
the remote by pressing any key.
listed, you will need to use section
The Red LED indicator at top
B.
right, should light up to indicate
that batteries are inserted
A. Manually
properly.
1. Press and hold the Setup key
until LED indicator blinks twice.
2. Enter the appropriate 4-digit setup
code for your device (from the
Code List) by pressing the number
keys (0-9) on the remote control
If the LED indicator blinks twice, a
returns to user mode.
correct code has been entered.
B. Change volume control from
If the LED indicator blinks 5 times,
STB to TV
an invalid code has been entered.
1. Press and hold the Setup key
Start over at step 1.
until LED indicator blinks twice.
2. Enter 993 by pressing the number
Notes:
keys on the remote control, LED
indicator will blinks twice.
If you are interrupted while you are
3. Press number key 2, LED
programming, the remote control
indicator will blinks twice.
may timeout before you complete
the code setup and you will need to
If an invalid code has been
start over. This is indicated by the
entered at step 2, LED indicator
LED indicator blinks 5 times, and
returns to user mode.
will blinks 5 times and return to
user mode. Start over at step 1.
If 15 seconds timeout occurs, the
B. Using the Automatic Search
1. Press and hold the Setup key
LED indicator blinks 5 times and
until LED indicator blinks twice.
returns to user mode.
2. Enter 991 by pressing the number
keys on the remote control, LED
Check TV Code been set to
indicator will blinks twice.
the remote
3. Press and hold the TV power
key, until the TV turns off.
If you need to check the TV code
that been set to the remote, you can
For step 3, code search will start
follow the step below.
1.5 seconds after press and hold
the TV power key.
1. Press and hold the Setup key
If an invalid code has been
until LED indicator blinks twice,
entered at step 2, LED indicator
then release Setup key.
will blinks 5 times and return to
2. Enter 990 by pressing the number
user mode. Start over at step 1.
keys on the remote control, LED
Press OK and EXIT key together
indicator will blinks twice.
to exit automatic search mode
3. To view the first code, Press
number key 1, wait 3 seconds and
Change Volume control
count on the number of LED
indicator blinks. (For example, 3
The remote is set to control volume
blinks, the code digit is 3)
level of STB. Once a valid TV code
Note: If code is 0, then LED
is programmed, the volume keys will
indicator will not blink.
control the TV volume
4. Repeat step 3 for three more
times. Press number key 2 for
A. Change volume control from
second digit; Press number key 3
TV to STB
for third digit; Press number key 4
1. Press and hold the Setup key
for fourth digit.
until LED indicator blinks twice.
2. Enter 993 by pressing the number
If an invalid code has been
keys on the remote control, LED
entered at step 2, LED indicator
indicator will blinks twice.
will blinks 5 times and return to
3. Press number key 1, LED
user mode. Start over at step 1.
indicator will blinks twice.
Resetting TV Configuration
If an invalid code has been
Settings
entered at step 2, LED indicator
will blinks 5 times and return to
1. Press and hold the Setup key
user mode. Start over at step 1.
until LED indicator blinks twice.
If 15 seconds timeout occurs, the
2. Enter 996 by pressing the number
LED indicator blinks 5 times and
keys on the remote control, LED
indicator will blinks twice.
Trouble –Shooting your
Remote Control
If an invalid code has been
entered at step 2, LED indicator
1. No red light shown on the
will blinks 5 times and return to
indicating light when pressing the
user mode. Start over at step 1.
keys of the remote control:
Check batteries are correctly
Resetting the Remote
installed.
Control to Factory Default
Change batteries if needed.
Settings
2. Red light shown when pressing
keys but remote cannot function:
1. Press and hold the Setup key
Check power of STB already On.
until LED indicator blinks twice.
Power Off then On the STB, and
2. Enter 981 by pressing the number
try to do pairing of remote and
keys on the remote control, LED
receiver.
indicator will blinks twice.
If an invalid code has been
entered at step 2, LED indicator
FCC ID: RCSRC2843002
will blinks 5 times and return to
user mode. Start over at step 1.
This device complies with Part 15 of
the FCC Rules. Operation is subject
Using your Remote Control
to the following two conditions:
1. This device may not cause
The remote control has been
harmful interference, and
designed to control functions of the
2. This device must accept any
programs and applications as
interference received, including
defined with the equipment
interference that may cause
specified.
undesired operation.
No installation is required for the
remote control to work.
You will need to install the batteries
You are cautioned that changes or modifications
(2X AAA).
not expressly approved by the party responsible
The Remote Control is able to
for compliance could void your authority to operate
the equipment.
function from a distance of 30
meters or more. As it uses RF
technology it is not necessary to
point at the STB to function. It is
able to function even when the STB
is not in your line of sight or is
blocked by other items or devices.
Care of your Remote Control
Do not use your Remote Control in
other ways that it was designed for.
Prevent water or other liquids from
damaging your Remote Control.
Check your batteries to ensure no
leaking batteries are used. For
optimum performance, change the
batteries after 6 to 9 months.
Related Manuals for Huawei RC2843002
Summary of Contents for Huawei RC2843002
- Page 1 For second and third harmful interference, and 1.5 seconds after press and hold designed to control functions of the Huawei RC2843002/01 digits, user has to press the digit 2. This device must accept any programs and applications as the TV power key.
- Page 2 Code List Commercial 1546,1447,1164 1546,2103,1049,1638,2143,2031,1013, 2219,1036 NexxTech 2360,1888 Sampo 2072,1038,1062,1312,1061,2143,2216, Technics 1049,1010 Solutions 1021,1063,1370,2359,2019,2043,1548, Ken Brown 1652 Nikko 1638,2143,1061,1015,1357 1638,1138,1554,2059,1327,1369,1010, Technika 1643 1051,1901,1908 Compaq 1697 1308,2020,1335,1239,2217,2055,2242, Kenwood 1638,2143,1061,1581 Niko 1894 1098 Technol Ace 1022 Abex 2060,1312,1098 Concerto 1638,2143,1363 1447,2237,1485,1068,1380,1385,1386, Kioto 1239 Nimbro 1603...