GE 15266 Installation Instructions

GE 15266 Installation Instructions

Smart digital timer
Available languages

Available languages

Quick Links

http://waterheatertimer.org/GE-timers-and-manuals.html
Smart Digital Timer
120VAC Hot
BLACK
Neutral
WHITE
Installation Instruction
1. Turn OFF the main power.
2. Remove the existing switch.
3. Connect the wires of Timer and wall box as followed by using the wire nuts provided.
a) Connect the Hot/Live wire of main power to the Black wire from Timer.
b) Connect both the Neutral wires of main power and Load to the White wire from Timer.
c) Connect the Hot/Live wire of Load to the Red wire from Timer.
d) Connect the Ground wire to the Green wire from Timer.
Note: Be sure that all wire nuts are secure.
4. Tuck the wires into the wall box leaving room for the Timer. Using the screws provided.
Mount the timer to the wall box being careful not to crush any wires.
5. Turn Main power ON
POWER-UP SEQUENCE:
1. Lift up the bottom of the door using a small slotted screwdriver.
2. Position the slide switch to TIMER.
3. Press the "RESET" button using a paper clip.
4. The display should flash 12:00AM on Monday.
Setting Current Time:
1. Press and HOLD the "CLOCK" key during this entire procedure.
2. Press the "HOUR" key to advance the hours.
3. Press the "MIN" key to advance the minutes.
4. Press the "DAY" key to advance the day.
5. If any keys are pressed for a prolonged period, the display will
advance rapidly.
6. Release the "CLOCK" key once the time and day have been entered. Now the timer is in
operation and ready to be programmed. The colon ":" after the hours will continuously
flash indicating that the clock is running.
Programming ON/OFF Events:
1. Press the "PROG" key once. TIMER 1 on - - : - - appears.
2. Using the "HOUR" and "MIN" keys enter the desired ON time. By default all days are
indicated. See block programming below for selecting different days. When complete press
the "PROG" key once.
3. Timer OFF --:-- will be displayed. Using the "HOUR" and "MIN" keys enter the desired OFF
time. By default all days are indicated. See block programming below for selecting different
days. When complete press the "PROG" key once.
4. If complete press the "CLOCK" key to return to current time
and day.
5. Note that a total of 7-ON and 7-OFF events can be programmed.
Block Programming:
1. When programming ON/OFF events, all days are indicated by default. To change the day
selection simply keep pressing the Day key and the display will change as follows:
2. Individual Day (MON, TUE, etc.)
3. MON~FRI; SAT~SUN; MON~SAT; MON~SUN
4. MON~WED~FRI; TUE~THU~SAT
5. MON~WED; THU~SAT
6. Follow the steps above to complete programming.
DST (Daylight Savings Time)
1. To activate DST press both of the "HOUR" and "MIN" keys at the same time. The present
time will increase by an hour and the screen will
show "DST"
2. To de-activate DST press the "HOUR" and "MIN" keys at the same time. The "DST" will
no-longer be on the screen.
RED
Lights/Fans/etc.
Ground
(GREEN)
Random, on/off Setting:
This feature sets the timer to switch lights ON and OFF at random intervals while
you are out of the house. This function will only operate if one or more programmed
switching commands are set.
1. To activate press the "DAY" and "HOUR" keys at the same time. Once activated the
"TIMER" symbol will be blinking.
2. To de-activate press the "DAY" and "HOUR" keys at the same time again. The
"TIMER" symbol will no longer be on the display.
Reviewing Programs:
1. To review the programs that have been entered, press and release the "PROG" key.
Each time you do this you will be able to scroll thru the programs.
2. Any program can be edited by pressing the "HOUR" , "MIN" , and "DAY" keys. Then
press the "PROG" key in order to accept the changes.
3. When complete press the "CLOCK" key to return to current time and day.
Deleting Programs:
1. To delete a particular program simply press the "PROG" key until the desired
program is displayed.
2. Then press the "HOUR" and "MIN" keys until --:-- is displayed. Then press the
"PROG" key in order to delete this particular program.
3. When complete press the "CLOCK" key to return to current time and day.
MEMORY BACKUP:
This timer is equipped with a rechargeable Ni-Mh battery which will protect your
programs during power failure for up to 30 days.
No need to replace battery.
Note that the screen blanks if the battery is discharged completely.
is a trademark of the General Electric Company and is used under license to Jasco
Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114.
This Jasco product comes with a 1 year limited warranty.
Visit www.jascoproducts.com for details.
15266
Electrical Ratings:
120VAC 60Hz
15A Resistive
15A Tungsten
1HP
*When done programming,
close door.
Manual Override:
Pressing the door will override the timer
setting and will manually turn the switch
ON and OFF .
Initial Startup:
When you initially program the unit it
may be necessary to press the manual
override key as the unit will not look
back to determine if it should be ON. For
example if the current time is 2:00PM
and you just programmed the unit to turn
ON at 1:00PM, you will need to press
the manual override key to turn it ON.
Thereafter, the unit will resume normal
operation (automatic).
loading

Summary of Contents for GE 15266

  • Page 1 15266 Smart Digital Timer Random, on/off Setting: This feature sets the timer to switch lights ON and OFF at random intervals while you are out of the house. This function will only operate if one or more programmed switching commands are set.
  • Page 2 3. La mention Timer OFF - - : - - (minuterie arrêt) s’affichera. Utilisez les touches « HOUR protège vos programmes pendant une panne de courant pour une période d’au plus 30 » (heure) et « MIN » (minutes) pour entrer l’heure d’arrêt voulue. Tous les jours sont jours.