1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. 1100 Series
  6. Installing and upgrading

Cisco 1100 Series Installing And Upgrading

Integrated services router
Hide thumbs Also See for 1100 Series:
Table of Contents

Quick Links

Installing and Upgrading Internal Modules and
FRUs
•
Installing and Upgrading Internal Modules and FRUs
This document describes how to install and upgrade internal modules and field replaceable units (FRUs) in
the Cisco 1100 Series Integrated Services Routers (ISRs). The install and upgrade information is contained
in these sections:

Safety Warnings

Class 1 laser product. Statement 1008
Warning
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030

Accessing Internal Modules

To access the internal modules on the router, you must first disconnect from the power source and then remove
the chassis cover. See the Replacing the Cover section for instructions on how to remove and later replace
the chassis cover on the routers.
Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network
Warning
voltages. Statement 1041
Installing and Upgrading Internal Modules and FRUs, page 1
Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router
1
Table of Contents
loading

Related Manuals for Cisco 1100 Series

Summary of Contents for Cisco 1100 Series

  • Page 1: Safety Warnings

    Installing and Upgrading Internal Modules and FRUs This document describes how to install and upgrade internal modules and field replaceable units (FRUs) in the Cisco 1100 Series Integrated Services Routers (ISRs). The install and upgrade information is contained in these sections: Safety Warnings Class 1 laser product.

  • Page 2: Replacing The Chassis Cover

    Step 5 Pull the cover to disengage the slots along the front (bezel) edge of the chassis, as shown in the figure below. Figure 1: Removing the Cover Slots Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router...

  • Page 3: Locating Internal And External Slots For Modules

    This section describes the locations of internal modules on the router motherboard. Internal modules include PoE daughter card on the Cisco1100 Series ISRs. Figure 2: Module Location in the Cisco 1100 Series ISR Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router...
  • Page 4 Close the chassis cover according to the instructions in the Replacing the Cover section, and connect the power supply cable. Figure 3: Internal PoE Daughter Card Assembly Screws PoE Daughter Card Metal Standoffs Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router...

  • Page 5: Removing And Replacing The Usb Flash Token Memory Stick

    Removing and Replacing the USB Flash Token Memory Stick The Cisco 1100 Series ISRs contain port for a 1 GB flash token memory stick to store configurations or Cisco IOS XE consolidated packages. Only Cisco USB Flash memory modules are supported by Cisco routers.

  • Page 6: Ac Power Supplies

    Gigabit Ethernet connectivity. The SFP module installs into a slot on the router rear panel. When selected in Cisco IOS software, it is assigned port gigabitethernet 0/0/0. The default is the built-in RJ-45 1000Base-T connector, which is enabled on this port.
  • Page 7 100BASE-LX SFP for FE port GLC-FE-100ZX 3.10 100BASE-ZX SFP (80km) GLC-FE-100EX 3.10 100BASE-EX SFP (40km) GLC-FE-100BX-D 3.11 100BASE-BX10-D GLC-FE-100BX-U 3.11 100BASE-BX10-U GLC-GE-100 3.10 100 V02 SFP on GE ports Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router...
  • Page 8 NM SFP Gigabit Ethernet and 1G/2G FC CWDM-SFP-1510 3.10 CWDM 1510 NM SFP Gigabit Ethernet and 1G/2G FC CWDM-SFP-1530 3.10 CWDM 1530 NM SFP Gigabit Ethernet and 1G/2G FC Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router...
  • Page 9 1532.68 nm SFP (100 GHz ITU grid) DWDM-SFP-3425 3.10 DWDM SFP 1534.25 nm SFP (100 GHz ITU grid) DWDM-SFP-3504 3.10 DWDM SFP 1535.04 nm SFP (100 GHz ITU grid) Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router...
  • Page 10 1542.94 nm SFP (100 GHz ITU grid) DWDM-SFP-4373 3.10 DWDM SFP 1543.73 nm SFP (100 GHz ITU grid) DWDM-SFP-4453 3.10 DWDM SFP 1544.53 nm SFP (100 GHz ITU grid) Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router...
  • Page 11 1552.52 nm SFP (100 GHz ITU grid) DWDM-SFP-5413 3.10 DWDM SFP 1554.13 nm SFP (100 GHz ITU grid) DWDM-SFP-5494 3.10 DWDM SFP 1554.94 nm SFP (100 GHz ITU grid) Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router...
  • Page 12 DWDM SFP 1560.61 nm SFP (100 GHz ITU grid) Use the show controller command at the Cisco IOS prompt to determine whether you are using an SFP certified by Cisco. Currently, GLC-GE-100FX V01 is not supported. Note Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router...

  • Page 13: Installing Sfps

    Use a pen, screwdriver, or other small straight tool to gently release a bale-clasp handle if you cannot reach it with your fingers. Step 4 Grasp the SFP on both sides and remove it from the router. Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router...
  • Page 14 Installing and Upgrading Internal Modules and FRUs Installing and Removing SFP Modules Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router...

Table of Contents