1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Firewall
  5. DFL-1000
  6. Quick install manual

D-Link DFL-1000 Quick Install Manual

Hide thumbs Also See for DFL-1000:
1
2
3
4
5
6
7
8
9
Table of Contents

Quick Links

See also: User Manual

1. Before you start

The DFL-1000 has the following settings when first powered on.
Operating Mode:
Administrator Account:
Internal Interface:
External Interface:
DMZ Interface:
Use the following table to gather the information you need to customize basic settings for your DFL-
1000.
Administrator Password:
Internal Interface:
External Interface:
Internal Server
Settings:
User name:
Password:
IP:
Netmask:
Manual:
IP:
Netmask:
Default Gateway:
Primary DNS Server:
Secondary DNS Server: 207.194.200.129
IP:
Netmask:
IP:
Netmask:
Manual:
IP:
Netmask:
Default Gateway:
Primary DNS Server:
Secondary DNS
Server:
Web Server:
Mail Server: SMTP:
FTP Server:
If you provide access from the Internet to a web server, mail server, or FTP
server installed on an internal network, add the IP addresses of the servers
here.
Quick Install Guide
NAT/Route
admin
(none)
192.168.1.99
255.255.255.0
192.168.100.99
255.255.255.0
(none)
207.194.200.1
10.10.10.1
255.255.255.0
_____._____._____._____
_____._____._____._____
_____._____._____._____
_____._____._____._____
_____._____._____._____
_____._____._____._____
_____._____._____._____
_____._____._____._____
_____._____._____._____
_____._____._____._____
POP3:
_____._____._____._____
DFL-1000
Version 2.27
Table of Contents
loading

Related Manuals for D-Link DFL-1000

Summary of Contents for D-Link DFL-1000

  • Page 1: Before You Start

    Quick Install Guide DFL-1000 Version 2.27 1. Before you start The DFL-1000 has the following settings when first powered on. NAT/Route Operating Mode: Administrator Account: User name: admin Password: (none) Internal Interface: 192.168.1.99 Netmask: 255.255.255.0 External Interface: Manual: 192.168.100.99 Netmask: 255.255.255.0...

  • Page 2: Advanced Settings

    You can configure the DHCP server using the setup wizard. Use the following table to record the IP address and netmask of the DFL-1000 DMZ interface if you are configuring it during installation.
  • Page 3 Make sure it has at least 1.5 in. (3.75 cm) of clearance on each side to allow for adequate air flow and cooling. The DFL-1000 can also be installed in a standard 19-inch rack. It requires 1 U of vertical space in the rack.

  • Page 4: Using The Firewall Setup Wizard

    Network activity at this interface. Amber No link established. 6. Using the Firewall Setup Wizard To run the Setup Wizard, you must connect to the DFL-1000 web- based manager. You require: • A management computer with an ethernet connection •...
  • Page 5 3. Start Internet Explorer version 4.0 or higher. Type https://192.168.1.99 into the Address field and press Enter. Your browser connects to the web- based manager and the DFL-1000 login page appears. 4. Type admin in the Name field and select Login.
  • Page 6 10. Set the default route to the Default Gateway IP address. For example to set the default route to 204.23.1.2 enter: set system route add 0.0.0.0 0.0.0.0 gw 204.23.1.2 dev external Once these addresses are set, you are ready to connect the DFL-1000 to your network.

  • Page 7: Advanced Configuration

    3. Optionally connect the DMZ interface to your DMZ network. 9. Advanced configuration You have completed the basic network setup of your DFL-1000. By default all traffic originating from your Internal network is allowed to reach the Internet, and all traffic originating from the Internet is blocked from reaching your internal network.

  • Page 8: 10. Troubleshooting

    This Quick Install Guide describes how to configure the DFL-1000 to run in Network Address Translation (NAT) mode. You can also configure the DFL-1000 to run in Transparent mode. Refer to the Transparent mode installation chapter of the DFL-1000 User Manual.
  • Page 9 Restarting the DFL-1000 At any time during the installation process if the DFL-1000 is not responding correctly, you can shut it down and restart it. Using the web-based manager: • Go to System > Status. • Select Restart. Using the CLI: •...

Table of Contents