Honeywell Thor VM3 User Manual

Honeywell Thor VM3 User Manual

Vehicle-mount rugged pc with microsoft windows embedded compact 7.0
Hide thumbs Also See for Thor VM3:
Table of Contents
Thor VM3
Vehicle-Mount Computer
with Microsoft® Windows® Embedded Compact 7.0
User Guide
Table of Contents
loading

Summary of Contents for Honeywell Thor VM3

  • Page 1 Thor VM3 Vehicle-Mount Computer with Microsoft® Windows® Embedded Compact 7.0 User Guide...
  • Page 2 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.
  • Page 3: Table Of Contents

    Additional Connectors...........................14 Components..............................15 Front View - Thor VM3 ..........................15 Back View - Thor VM3 ..........................16 Access Panels - Thor VM3 ........................17 Front View - Dock ............................17 Back View - Dock ............................18 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 4 External AC Power Supply ........................27 Uninterruptible Power Supply ......................27 Backup Battery ............................29 Fuse ................................29 Power Management Modes........................29 Power Controls............................32 External Connectors ............................34 Serial Connector (COM1 and COM2) ....................34 USB Connector(s) .............................35 Ethernet Connector ..........................35 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 5 Procedure - RAM Mount Assembly....................58 Install U Bracket Mount..........................69 Components - U Bracket Mounting Assembly................69 Procedure - U Bracket Assembly ......................70 Connect Cables ..............................73 Strain Relief Cable Clamps ........................73 Connect Power............................74 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 6 Windows Embedded Compact Operating System................133 General Windows Embedded Compact Keyboard Shortcuts..........133 Save Changes to the Registry ......................134 Software Load..............................135 Software Applications .......................... 135 ActiveSync..............................135 RFTerm (Optional) ..........................135 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 7 Advanced..............................144 Thor VM3 OS Upgrade ..........................145 Introduction ............................. 145 Preparation............................... 145 Procedure..............................146 BIOS................................... 146 Accessing the BIOS Setup........................147 Control Panel ..............................148 About................................150 Accessibility ............................. 152 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 8 Stylus ................................206 System................................ 207 Terminal Server Client Licenses ...................... 209 Volume and Sounds..........................210 ZoomZone ..............................212 Automatic Firmware Update Utility....................... 215 Firmware Distribution Files ....................... 215 Update Process............................215 viii Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 9 Tasks ................................231 Status................................231 Profile List..............................231 Admin Login............................. 232 Browse Nearby Wireless Networks....................233 Creating a Profile ........................... 234 Advanced Profile Configuration....................... 235 Roam Management ..........................257 Advanced Settings..........................261 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 10 VM3D and VMXD Enhanced Dock....................300 Environmental Specifications......................... 301 Thor VM3 and Dock..........................301 Network Card Specifications ........................302 WLAN - Qualcomm Atheros 802.11a/b/g/n ................302 WPAN - Bluetooth..........................302 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 11 USB2 Connector............................. 307 CANbus / Audio Connector ....................... 310 Hat Encoding ..............................313 Licenses of Third Party Software ......................315 Appendix C - Thor VM3 Agency Information............365 Label Locations ............................365 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 12 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 13: Chapter 1 - Customer Support

    CHAPTER CUSTOMER SUPPORT Product Service and Repair Honeywell International Inc. provides service for all of its products through service cen- ters throughout the world. To obtain warranty or non-warranty service, please visit www.honeywellaidc.com/locations to find contact information for your region’s service center.
  • Page 14: Limited Warranty

    These warranties are non-transferable. The duration of the limited warranty for the Thor VM3 is 1 year. The duration of the limited warranty for the Thor VM3 Dock is 1 year. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 15 The duration of the limited warranty for the Thor VM3 Vehicle Mount Assembly is 1 year. The duration of the limited warranty for the Thor VM3 internal UPS battery is 1 year. The duration of the limited warranty for the Thor VM3 AC power supply and cables is 1 year.
  • Page 16 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 17: Chapter 2 - Getting Started

    The Thor VM3 contains a UPS battery which, when fully charged, can power the Thor VM3 for a minimum of 30 minutes. This can be when the Thor VM3 is not attached to a dock or when the Thor VM3 is attached to a dock but the vehicle power is interrupted, such as when the vehicle battery is being changed.
  • Page 18: About This Guide

    • RAM or U-Bracket vehicle mount kit If you ordered additional accessories for the Thor VM3, verify they are also included with the order. Keep the original packaging material in the event the Thor VM3 should need to be returned for service. For details, see Product Service and Repair.
  • Page 19: Initial Setup For Thor Vm3

    8. Press the Power Button on the Thor VM3. Note: After the initial power on, the Thor VM3 can be configured to automatically power on, either when power is attached or the vehicle ignition is turned on. 9. Perform touch screen Calibration.
  • Page 20: Software Setup

    Speaker Volume. 4. Configure Bluetooth Printing Bluetooth Scanning. 5. Set wireless client parameters using the WLAN Wireless Configuration Utility (WCU). 6. Set terminal emulation parameters. Save Changes to the Registry. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 21: Dock

    VMXD Enhanced Dock for Off-Vehicle Use All docks provide: • A mount for the Thor VM3 computer. The dock attaches to a vehicle via a RAM or U- bracket mount or to a RAM table stand for use in an office environment. •...
  • Page 22: Vm1D Standard Dock

    USB port provides host connection via an adapter cable. This port also supports Honeywell external keyboards. Ethernet CANbus CANbus connection via an adapter cable Audio Headset connection via an adapter cable Screen Supported via COM1 and COM2 connectors. Blanking Ignition Supported Control Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 23: Vm3D Enhanced Dock

    RJ-45 Ethernet connection on top of dock. CANbus CANbus connection via an adapter cable Audio Headset connection via an adapter cable Screen Supported via COM1 and COM2 connectors. Blanking Ignition Supported Control Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 24: Vmxd Enhanced Dock

    Caution: This dock is designed for DC power vehicle-mounted applications only. This dock is designed for use when the Thor VM3 is replacing a Thor VX8 or Thor VX9. This dock utilizes the existing vehicle wiring from the earlier computer and supports screen blanking through that wiring.
  • Page 25: Vmxd Enhanced Dock For Off-Vehicle Use

    RJ-45 Ethernet connection on top of dock. CANbus CANbus connection via an adapter cable Audio Headset connection via an adapter cable Screen Supported via COM1 and COM2 connectors. Blanking Ignition Supported Control Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 26: Additional Connectors

    Additional Connectors External antenna connectors may be present on the back of the Thor VM3. The connec- tors may include: • 802.11 antenna connectors, used when the Thor VM3 is not equipped with internal antennas. • External GPS antenna connector, when the Thor VM3 is equipped with GPS.
  • Page 27: Components

    Components Front View - Thor VM3 Microphone Power Ambient Button Light Sensor Speakers Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 28: Back View - Thor Vm3

    Back View - Thor VM3 External Antenna Connectors WWAN Antenna Cable Access Panel Card mSATA Access Panel Provision for Dock Provision for Padlock Quick Release Handle Contact Laptop Security Pads Cable Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 29: Access Panels - Thor Vm3

    SIM card slots Front View - Dock Standard Dock Dock Contact Pads Enhanced Dock The Enhanced Dock has a foam surround around the dock contact pad. Dock Contact Pads Foam Surround Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 30: Back View - Dock

    COM2 port on the dock. If a screen blanking box is not connected via the power cable, the COM1 port on the dock is available for a serial device Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 31: Top View - Enhanced Dock

    3. Press the Blue key to exit Blue mode. Refer to the Screen Control panel for the current display brightness level. Screen Blanking The Thor VM3 can be configured to blank (blackout) the display while the vehicle is in motion. Refer to ZoomZone for information.
  • Page 32: Keypad Backlight

    Power Up If a USB drive, such as a thumb drive is attached to the Thor VM3, the device may attempt to boot from the USB drive. Remove the USB drive and power up the Thor VM3 again.
  • Page 33: Rebooting The Thor Vm3

    • Use the P1 + P7 + Orange key press sequence to reboot the Thor VM3. The keys must be pressed in sequence; they do not need to be held down simultaneously. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 34: Tapping The Touch Screen With A Stylus

    Clearing Persistent Storage / Reset to Default Settings Use the Registry control panel Load Factory Defaults button to set the Thor VM3 regis- try back to factory defaults. No other clearing is available or necessary. Tapping the Touch Screen with a Stylus Note: Always use the point of the stylus for tapping or making strokes on the touch screen.
  • Page 35: Setup Terminal Emulation Parameters

    Note: These instructions are for components made of glass. If there is a removable protective film sheet on the display, remove the film sheet before cleaning the screen. Keep rough or sharp objects away from the Thor VM3 touch screen and, if installed, the bar code reader scanning aperture.
  • Page 36 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 37: Chapter 3 - Hardware Overview

    CHAPTER HARDWARE OVERVIEW System Hardware 802.11a/b/g/n Wireless Client The Thor VM3 has an 802.11a/b/g/n network card that supports diversity with two internal or external antennas. Power management for the network card is configured with the WLAN Wireless Configuration Utility (WCU).
  • Page 38: Video Subsystem

    When a headset is plugged into the adapter cable, the main speakers are disabled. A microphone is located at the upper right of the Thor VM3 display, near the Thor VM3 emblem. When a headset is plugged into the adapter cable, the internal microphone is disabled.
  • Page 39: Power

    Universal Input Power Supply can be used to convert AC wall power to an appropri- ate DC level. AC to DC power input for the Thor VM3 is delivered to the dock via an optional external power supply and adapter cable. See External AC/DC Power Supply.
  • Page 40 Move the Thor VM3 to a different location to charge the UPS battery. When the Thor VM3 is operated in an environment where the UPS battery is not able to charge due to temperature extremes, the Thor VM3 should be removed to a location within the safe charging temperature range during off hours.
  • Page 41: Backup Battery

    Power Management Modes On Mode (D0) When the Thor VM3 is attached to either vehicle power or an external power supply or is operating from the UPS battery and the power button is pressed, the Thor VM3 is in the On mode.
  • Page 42 By default power is turned off to the USB port when the Thor VM3 is in Suspend. The Thor VM3 can be configured to provide power to the USB port in Suspend using the Options control panel.
  • Page 43 Touch on the touch screen System Primary Events A System Primary Event allows the Thor VM3 to transition to D2 (System Idle) but the Thor VM3 does not enter D3 (Suspend) as long the system event occurs. System primary events include: •...
  • Page 44: Power Controls

    Please refer to the Power Configuration Mode control panel for complete details. For information on the Ignition input signal see Vehicle 10-60VDC Direct Power Connection Auto-On Control Wiring Diagram. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 45 AC/DC The Thor VM3 is designed to power on whenever external power is attached. Due to the presence of external power, longer default power management timeouts are used. Ignition Control The Thor VM3 is configured to power on when the vehicle ignition is switched on. When the vehicle ignition is on, longer default power management timeouts are used.
  • Page 46: External Connectors

    Power the Thor VM3 off before attaching a cable to any port (serial, USB, Audio/CAN, etc.). The external I/O connectors for the Thor VM3 are located on the right side of the dock (when viewed from the back). Power Supply Connector is on the left side of the dock (when viewed from the back).
  • Page 47: Usb Connector(S)

    An additional USB host port is located on the top of the Enhanced Dock. Lift the cover to access the USB port. Ethernet Connector An Ethernet port is located on the top of the Enhanced Dock. Lift the cover to access the Ethernet port. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 48: Canbus / Audio Connector

    See Dock for details. Power Supply Connector for connector pin- Standard Dock Enhanced Dock out detail. See Connect Power for more infor- mation on connecting power to the Thor VM3. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 49: Antenna Connections

    1. WI-FI (MAIN) 802.11 Main Exter- nal Antenna Con- nector The Thor VM3 is equipped with an 802.11 radio and can be 2. WAN (MAIN) (Blue ordered with internal antennas, external antennas or exter- label) Main WWAN nal remote mount antennas. When the Thor VM3 is ordered...
  • Page 50: Keyboard Options

    The integrated keypad backlight and the display share the same timer, which is configured in the Power control panel. • The integrated keypad backlight can be disabled via the Misc tab of the Options control panel. Keypad LEDs Keyboard LEDs for details. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 51: Usb Keyboards

    Ctrl Enter The Thor VM3 uses an optional rugged QWERTY 95 key keyboard, designed for ease of use with the Windows operating system. The USB keyboard connects directly to the D9 USB connector (Standard Dock) or USB1 connector (Enhanced Dock).
  • Page 52 Since the keyboard is a USB device, by default the external keyboard backlight is turned off when the Thor VM3 enters Suspend. This behavior can be changed by enabling USB power in Suspend on the Misc tab of the Options control panel.
  • Page 53: Ps/2 Keyboards

    PS/2 Keyboards Legacy PS/2 keyboards can be used with the Thor VM3 via a USB to PS/2 adapter cable. PS/2 keyboards are available in 60-key and 95-key versions and were used with the VX6, VX7, Thor VX8 or Thor VX9.
  • Page 54 However these keys send distinctly different scan codes when the keys are pressed. The default codes for the Thor VM3 number keys cor- respond to the numeric keypad on standard keyboards. In order to duplicate the codes sent when the alphanumeric key is pressed, the hidden keystroke must be used.
  • Page 55 F4 and F5 keys are not used as the display brightness is adjusted via the buttons on the Thor VM3. • The 2 functions of the F6 and F7 keys are not used as the Thor VM3 has TFT LCD screen with no provision for contrast adjustments. • The 2 functions of the F8 and F9 keys are not used as the sound volume on the Thor VM3 is controlled with the Sound icon in the Microsoft Windows System Tray.
  • Page 56: Usb Keyboard / Mouse

    USB Keyboard / Mouse A standard USB keyboard or mouse can be attached to the Thor VM3 using the appro- priate adapter cable. The Y cable attaches to the Thor VM3 and provides a USB connector. Please refer to documentation provided with the USB keyboard or mouse for more information on their operation.
  • Page 57: Led Functions

    Green blinking very slowly • Suspend External power present (1/2 sec. on, 4 1/2 sec. off) • External power present • Suspend External power not present • • SuspendOff External power not present Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 58 (1/8 sec. on, 1/8 sec. off) • Charge timeout • UPS is not installed SSD (Solid State Drive) LED LED Behavior Status Flashing Green SSD read or write activity No SSD read or write activity Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 59: Connection Leds

    Indicates a connection with an IP address to an Access Point Indicates no connection to an Access Point Bluetooth LED LED Behavior Status Bluetooth hardware is on Bluetooth hardware has been turned off Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 60: Keyboard Leds

    Orange mode is not invoked. Programmable LED The Programmable LED is available for user applications. The LED defaults to Off unless activated by user application. The LED behavior is controlled by the NLedDriverSetDevice API. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 61: Display

    Technical Assistance for availability. Note: If the touch screen is disabled or loses calibration on a Thor VM3, you must use a USB mouse or keyboard attached to the Thor VM3 to access the control panel to re-enable or recalibrate the touch screen unless a programmable key has been assigned to that function.
  • Page 62: Display Backlight Control

    Display Backlight Control The display brightness on a Thor VM3 equipped with an outdoor display can be config- ured to automatically adjust depending on the ambient light level via Screen Control. Note: When automatic brightness control is enabled, the user can still manually adjust brightness.
  • Page 63: Chapter 4 - Vehicle Mounting And Accessory Installation

    For an AC powered application: Use an AC/DC power supply and the VMXD off- vehicle enhanced dock. The Thor VM3 is designed to be mounted to a dock in a vehicle with either a RAM mount or U Bracket system. A power cable is provided with the Thor VM3 dock. An optional 21 key numeric or 95 key laptop-style USB keyboard and keyboard mounts are available.
  • Page 64: Prepare For Vehicle Mounting

    Quick Start The following list outlines, in a general way, the process to follow when mounting the Thor VM3 in a vehicle. Refer to the following sections in this document for more details. Install RAM Mount Install U Bracket Mount to the vehicle.
  • Page 65: Maintenance - Vehicle Mounted Devices

    1. Locate the notch on the upper rear of the Thor VM3. 2. Slide this notch over the top lip of the dock. Slide the Thor VM3 from side to side on the dock to make sure it fully engages on the lip of the dock. If the Thor VM3 cannot be slid side to side, the lip is engaged.
  • Page 66 When the Thor VM3 is placed in the dock, the following may happen: • If the Thor VM3 is off and power is connected to the dock, the Thor VM3 may boot when placed in the dock. The behavior depends on the Power Configuration Mode selected.
  • Page 67: Dock I/O Pin Cover

    Dock I/O Pin Cover. The dock contains a tethered I/O Pin Cover to protect the I/O pins on the dock when a Thor VM3 is not mounted in the dock. • When the Thor VM3 is not installed in the dock, use the I/O Pin Cover to protect the pins on the dock as shown.
  • Page 68: Install Ram Mount

    In addition to the kits below, individual RAM mounting components are also available. Mounting Kits without Keyboards Each mounting kit contains: RAM Ball (Size D) for back of Thor VM3 dock with hardware (screws and washers) to attach RAM ball to dock...
  • Page 69 Hardware (cone washers and nuts) to attach Ball to Plate Mounting Kits with Integrated Keyboard Mounting Additionally, the kits for the Thor VM3 with an integrated 95 key keyboard mount include: Thor VM3 Keyboard Mounting Bracket RAM Ball (Size C) with hardware (nuts) to attach RAM ball...
  • Page 70: Procedure - Ram Mount Assembly

    Equipment Needed: Sockets, screwdriver and a Torque wrench capable of measuring to 50 inch pounds (5.64±.56 N/m). Note: Torquing tool is not supplied by Honeywell. Tools needed to attach the RAM Clamp Mount to the vehicle are not supplied by Honeywell.
  • Page 71 1. Determine the position for mounting the RAM ball base. Be sure to position the RAM bracket to allow access to the switches and ports on the bottom of the Thor VM3. 2. Attach the RAM ball base to the vehicle mounting surface using three or four 1/4 bolts (not included) or equivalent fasteners.
  • Page 72 2” (50.8 mm) thick. The clamp may be attached to a thicker beam by substituting longer bolts (not included). Be sure to position the RAM clamp mount to allow access to the switches and ports on the bottom of the Thor VM3. Bolts...
  • Page 73 1. Determine the position for mounting the RAM ball plate. Be sure to position the RAM plate to allow access to the switches and ports on the bottom of the Thor VM3. 2. Attach the RAM ball plate to the vehicle mounting surface using four 1/4 bolts (not included) or equivalent fasteners.
  • Page 74 3. If using the external keyboard mount, position the Keyboard Bracket and the Size D RAM ball on the rear of the Thor VM3 dock, aligning the holes on the back of the Thor VM3 dock with the holes on the bracket and the RAM ball base.
  • Page 75 Step 3 – Attach Thor VM3 Assembly to RAM Mount 1. Slip the Size D RAM arm over the ball on the vehicle RAM mount (RAM Ball mount shown). 2. Insert the ball on the dock into the RAM arm and tighten the knob on the RAM arm using the supplied RAM wrench.
  • Page 76 Step 4 – Place the Thor VM3 into the Dock If the Thor VM3 is not already mounted to the dock, Place Thor VM3 in the Dock If the optional external keyboard is not used, the mounting process is complete.
  • Page 77 Step 5 – Attach Alphanumeric Keyboard to Mounting Plate (Optional) Note: This step is only for a Thor VM3 with the optional external keyboard. If using the optional integrated keyboard mount, attach the keyboard to keyboard mounting plate, using four #8 screws, flat washers and lock washers.
  • Page 78 Note: This step is only for a Thor VM3 with the optional external keyboard. 1. Slip the Size C RAM arm over the ball on the Thor VM3 Keyboard Bracket. 2. Slip the ball on the Keyboard Mounting Plate into the other end of the Size C RAM arm.
  • Page 79 3. Slip the RAM arm over the accessory RAM ball. 4. Slip the RAM ball on the keyboard into the RAM arm. 5. Tighten the knob on the RAM arm while adjusting to the desired angle. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 80 3. Slip the RAM arm over the accessory RAM ball. 4. Slip the RAM ball on the scanner holder into the RAM arm. 5. Tighten the knob on the RAM arm while adjusting to the desired angle. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 81: Install U Bracket Mount

    With a U Bracket included for new vehicle installations • Without a U Bracket for installing the Thor VM3 in place of a previous Honeywell vehicle mounted computer, such as a VX6 or VX7. U Bracket (only necessary for new installations)
  • Page 82: Procedure - U Bracket Assembly

    The adapter bracket can be mounted in a high or low position, depending on viewing position, as shown below. Additionally, the slotted U bracket allows the Thor VM3 to be mounted vertically or tilted forward or backward for best viewing angle.
  • Page 83 4. 1.02 in / 25.9 mm 5. 3.38 in / 85.85 mm 6. Vehicle Mount Footprint 7. 0.406 in / 10.312 mm 8. 0.88 in / 22.3 mm 9. 1.25 in / 31.75 mm Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 84 Step 2 - Remove RAM Ball If the Thor VM3 dock has a RAM ball attached, the RAM ball must be removed from the dock to use the U Bracket mount. Remove the RAM ball. The hardware used to attach the RAM ball to the dock is not reused for the U bracket mount.
  • Page 85: Connect Cables

    Connect Cables There are many cables available for the Thor VM3 including power cables, and data/ communication cables. Strain Relief Cable Clamps Equipment Required: Phillips screwdriver (not supplied by Honeywell) There are five strain relief cable clamps secured to the Standard Dock.
  • Page 86: Connect Power

    - For applications where a Thor VM3 (with a VMXD Enhanced Dock) replaces a previously installed Thor VX8 or Thor VX9. When using the Thor VM3 with AC power, use the VMXD Enhanced Dock for Off-Vehi- cle Use and: •...
  • Page 87: Power Cable Routing

    The power cable is less flexible in low temperature environments. Avoid sharp bends. Caution: Regularly inspect power cable for damage, especially in low temperature environments. Contact Technical Assistance replacement cable options. Power Cable Routing Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 88 Note: Correct electrical polarity is required for safe and proper installation. See the figures below for additional wire color-coding specifics. The Thor VM3 DC input wires (Red, Red/White DC+ and Black, Black/White DC-) and the Blue ignition input wire are galvanically isolated. The Green ground input is used for electrostatic discharge (ESD) protection.
  • Page 89 Vehicle 10-60VDC Direct Power Connection 1. The Thor VM3 must not be mounted in the dock. The power switch on the dock must be turned Off. The power cable must be UNPLUGGED from the dock. 2. While observing the Fuse Requirements, connect the power cable as close as possible to the actual battery terminals of the vehicle (if using unswitched power).
  • Page 90 12VDC. • For 24VDC input, use the 6A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than 24VDC. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 91 For 48VDC input, use the 3A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than 48VDC. Note: For North America, a UL Listed fuse is to be used. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 92 12VDC. • For 24VDC input, use the 6A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than 24VDC. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 93 For 48VDC input, use the 3A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than 48VDC. Note: For North America, a UL Listed fuse is to be used. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 94 12VDC. • For 24VDC input, use the 6A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than 24VDC. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 95 For 48VDC input, use the 3A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than 48VDC. Note: For North America, a UL Listed fuse is to be used. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 96 These instructions are for use with VM1D Standard Dock VM3D Enhanced Dock only. This option requires DC/DC external power supply Honeywell Part no. 9000313PWR- SPLY. Shown With Lid Attached Shown With Lid Removed • Lid is secured with screws on the •...
  • Page 97 Wiring Diagram, before beginning power cable install. 2. The Thor VM3 must not be mounted in the dock. The power switch on the dock must be turned Off. The power cable must be UNPLUGGED from the dock. 3. Route the cable from the Thor VM3 to the DC/DC power supply. Route the power cable the shortest way possible.
  • Page 98 + and V - terminals. 8. Connect the ground (green) wire from the Thor VM3 to the GND terminal on the input side of the DC/DC power supply. 9. Route the wiring from the DC/DC power supply to the vehicle’s electrical system. Do not connect to vehicle power at this time.
  • Page 99 17. Connect the watertight connector end of the power cable to the Thor VM3 dock power connector by aligning the connector pins to the power connector; push down on the watertight connector and twist it to fasten securely.
  • Page 100 For all voltages, use the 3A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than the vehicle input voltage. Note: For North America, a UL Listed fuse is to be used. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 101 The power supply should be mounted in a dry location within the vehicle or placed in a suitable protective enclosure. Caution: Use caution when routing the power cable. See Power Cable Cautions. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 102 Wiring Diagram, before beginning power cable install. 2. The Thor VM3 must not be mounted in the dock. The power switch on the dock must be turned Off. The power cable must be UNPLUGGED from the dock. 3. Route the cable from the Thor VM3 to the DC/DC power supply. Route the power cable the shortest way possible.
  • Page 103 14. Use proper electrical and mechanical fastening means for terminating the cable. Properly sized “crimp” type electrical terminals are an accepted method of termination. Select electrical connectors sized for use with 18AWG (1mm conductors. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 104 16. Connect the watertight connector end of the power cable to the Thor VM3 dock power connector by aligning the connector pins to the power connector; push down on the watertight connector and twist it to fasten securely.
  • Page 105 For all voltages, use the 3A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than the vehicle input voltage. Note: For North America, a UL Listed fuse is to be used. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 106 Enhanced Dock only. An adapter cable is available to attach the Thor VM3 to a vehicle previously equipped with a VX6/VX7 DC power cable. The adapter cable has a 5-pin connector to match with the VX6/VX7 power supply cable on one end and a 6-pin connector to match to the Thor VM3 on the other end.
  • Page 107 VM3 on the other end. The cable also has bare wires for ground and ignition sense con- nection plus a D9 cable to connect to a COM port on the Thor VM3 dock to provide a screen blanking signal. This section assumes the VX8/VX9 power cable is properly con- nected to vehicle power.
  • Page 108 7. Connect the watertight connector end of the power cable to the Thor VM3 dock power connector by aligning the connector pins to the power connector; push down on the watertight connector and twist it to fasten securely.
  • Page 109 CV61 DC power cable. The adapter cable has a 5-pin connector to match with the VV61 power supply cable on one end and a 6-pin connector to match to the Thor VM3 on the other end. This section assumes the CV61 power cable is properly connected to vehicle power.
  • Page 110 Honeywell Screen Blanking Box Cable An optional Honeywell Screen Blanking Box Cable is available. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 111 Connected to Screen Blanking Box, switched Gray (see note) side Note: Wire colors only apply to optional Honeywell Screen Blanking Box Cable, VM1080CABLE. Wire colors may vary in a user-supplied cable. The optional Honeywell Screen Blanking Box Cable, VM1080CABLE, is installed as fol-...
  • Page 112 To pin 7 of COM1 or COM2 To pin 8 of COM1 or COM2 Note: The black and gray wire colors in the illustration only apply to the optional Honeywell Screen Blanking Box Cable, VM1080CABLE. The wire colors may be different in a user- supplied cable.
  • Page 113 To pins 7 and 8 of COM1 or COM2 port on dock Pins 7 and 8 must be connected as shown in the illustration above. No other pins are to be connected. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 114 VX8/VX9 power cable and screen blanking box to be used when the VX8/VX9 is replaced by a Thor VM3 computer. These instructions are for this dock model only! The Ignition Control feature is not available when this dock is used.
  • Page 115 DC/DC Supplied Power Cable Power (Shielding to be trimmed) Supply Caution: For battery powered vehicles: • + is connected to battery positive. • - must be connected to battery negative. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 116 Caution: For internal combustion engine powered vehicles: • + is connected to battery positive. • - is connected to battery negative. • is connected to the vehicle chassis ground, which can also be battery negative. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 117 Caution: For battery powered vehicles: • + is connected to battery positive. • - must be connected to battery negative. • GND must be connected to the vehicle chassis ground. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 118 Caution: For internal combustion engine powered vehicles: • + is connected to battery positive. • - is connected to battery negative. • GND is connected to the vehicle chassis ground, which can also be battery negative. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 119 5. Press the Power Switch on the back of the Thor VM3 dock. 6. Press the Power Button on the front of the Thor VM3 to turn on the Thor VM3. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 120 Table Stand When the Thor VM3 is used in an office environment, it can be mounted in a table stand. To use the table stand: 1. Attach the RAM ball to the RAM Metal Table Stand with the supplied screws and nuts.
  • Page 121: Connect Usb Keyboard

    1. Seat the keyboard cable connector over the USB or USB1 connector on the dock. 2. Tighten the thumbscrews in a clockwise direction. Do not over tighten. 3. Secure the cable to the Thor VM3 with Strain Relief Cable Clamps. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 122: Connect Ps/2 Keyboard

    A legacy PS/2 keyboard (used with VX6, VX7, Thor VX8 or Thor VX9), available in either 60-key or 95-key versions can be used with the Thor VM3 via a PS/2 to USB adapter cable. This function is only supported with the VM3D or VMXD Enhanced Docks. It is not supported with the VM1D Standard Dock.
  • Page 123 5. Secure the cable to the Thor VM3 with Strain Relief Cable Clamps. The strain relief must capture the keyboard cable. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 124: Connect Usb Host

    USB Client Connector USB and USB1 Connector for connector pinouts. Note: The USB client connection is not available on the Thor VM3. 1. Seat the D9 connector firmly over the USB (Standard Dock) or USB1 (Enhanced Dock) connector on the dock.
  • Page 125 USB scanner, it may be necessary to unplug the scanner and plug it back into the USB port in order for the auto-detect function to display the scanner settings. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 126: Connect Usb Client

    Connect USB Client Note: The USB client connection is not used on the Thor VM3. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 127: Connect Serial Device

    1. The scanner cable is attached to either the COM1 or COM2 port on the dock. 2. Connect the serial cable for the scanner as directed above. 3. When the Thor VM3 is powered on, it provides power to the serial scanner. 4. Configure the Data Collection (DC) Wedge to manipulate scanned data as desired.
  • Page 128 3. Slide the cable ends together until they click shut. Do not twist or bend the connectors. The Thor VM3 internal microphone and speakers are automatically disabled when the headset is connected. Adjust Headset / Microphone and Secure Cable The headset consists of an earpiece, a microphone, a clothing clip and a cable.
  • Page 129: Connect Canbus Cable

    Connect CANbus Cable The CANbus/Audio connector supports a headset adapter cable or a CANbus Y cable. The Thor VM3 does not support connecting audio and CANbus simultaneously. CANbus / Audio Connector for connector pinouts. 1. Seat the D15 cable end connector firmly over the CANbus/Audio Connector on the dock.
  • Page 130: Install Remote Antenna

    The Vehicle Remote Mount Antenna cannot be used by devices with an internal antenna. Components and Mounting Diagram Washer Washer Bracket To antenna Antenna To antenna Bracket To antenna connector on computer Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 131 6. Connect the cable to the antenna connector (Wi-Fi Main or Wi-Fi Aux) on the Thor VM3. If only one antenna is used, be sure to connect it to the Wi-Fi Main connector. 7. Repeat the steps above for the second 802.11 antenna. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 132 5. Attach the one end of the coaxial cable to the antenna and the other end to the Mobile Net WWAN connector on the vehicle mounted Thor VM3. 6. Use cable ties to secure the coaxial cable to the vehicle as necessary. Make sure the cable is routed so it is not damaged by any moving parts of the vehicle.
  • Page 133 5. Use cable ties to secure the coaxial cable to the vehicle as necessary. Make sure the cable is routed so it is not damaged by any moving parts of the vehicle. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 134: Apply Touch Screen Protective Film

    Apply Touch Screen Protective Film The optional Thor VM3 touch screen protective film is shipped in packs of 10. The pro- tective film is flexible and treated with an anti-glare coating on the outer surface. The protective film is slightly larger than...
  • Page 135: Removal

    2. Lift up on the edge of the protective film so it does not slide between the touch screen and display housing when the protective film is slid back to the center. 3. Repeat until all edges are free and remove the protective film. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 136: Disconnect Ups Battery

    Torquing tool capable of measuring inch pounds • #2 Phillips screwdriver bit Disconnect Procedure 1. For convenience, the Thor VM3 can be removed from the dock, though it is not nec- essary. 2. If the Thor VM3 remains in the dock, disconnect the power cable from the dock.
  • Page 137: Install Msata Drive

    Torquing tool capable of measuring inch pounds • mSATA card Installation Procedure Note: Install any SIM cards before installing the mSATA drive. 1. Place the Thor VM3 in Suspend by pressing the Power button. 2. Remove the Thor VM3 from the dock. Disconnect UPS Battery.
  • Page 138 10. Reinstall the Thor VM3 in the dock. 11. Restart the Thor VM3. 12. When using Windows explorer to view My Computer, the mSATA expansion card is identified as System2. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 139: Install Sim Card(S)

    VM3 WWAN Connection Manager for software configuration. Note: The SIM card is not hot-swappable. After installing or removing a SIM card, the Thor VM3 must be rebooted for the change to take effect. Equipment Required The following equipment is user-supplied: •...
  • Page 140 10. Lower the SIM holder to back to its flat position. 11. Slide the silver retainer clip back toward the outside edge of the Thor VM3. This locks the SIM card in place. 12. Reattach the access panel, torquing the screws to 7.0 ± 0.5 inch pounds.
  • Page 141 15. Restart the Thor VM3 (Start > Settings > Control Panel > Registry and tap the Restart button). Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 142: Replace Front Panel

    Replace Front Panel Front Panel Options The front panel of the Thor VM3 is field replaceable. The front panel assembly contains the keypad, touch screen and optional defroster. Should any of these components fail, the front panel assembly can easily be replaced to reduce downtime. The replacement front panel is available in these configurations: •...
  • Page 143 #2 Phillips bit and torque the screws to 7 ± 0.5 inch pounds. 10. Reinstall the Thor VM3 in the dock. 11. When the Thor VM3 is placed in the powered dock, the UPS battery automatically reconnects.
  • Page 144 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 145: Chapter 5 - Software

    Your Thor VM3 operating system is Microsoft Windows Embedded Compact 7. The Thor VM3 operating system revision is displayed on the Desktop. This is the default set- ting for the Desktop Display Background. Windows Embedded Compact Operating System This segment assumes the system administrator is familiar with Microsoft Windows options and capabilities loaded on most standard Windows computers.
  • Page 146: Save Changes To The Registry

    UPS charge reaches a critically low level and external power is not available. The registry save process takes 0 – 3 seconds. If nothing has been changed, nothing is saved (e.g., 0 seconds). Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 147: Software Load

    • Network and Device Drivers • Bluetooth Note: Please contact Honeywell Technical Assistance for software updates and CAB files as they are released by Honeywell. Software Applications The following applications are included: •...
  • Page 148: Enterprise Te (Optional)

    Music Player is supported on the VM3. However, the Save function should not be used due to an issue within this Microsoft product. Enterprise Client Pack There are several components of the Enterprise Client Pack installed on the Thor VM3. For more information on these programs visit the Thor VM3 product page at www.honeywellaidc.com.
  • Page 149: Thor Vm3 Utilities

    Order is used to force a sequence of events. Order=0 is first, and Order=99 is last. Order must be greater than 4 for the Thor VM3. Two items which have the same order will be installed in the same pass, but not in a predictable sequence.
  • Page 150: Launch.exe And Persistent Storage

    System\Desktop copied to Windows\Desktop System\Favorites copied to Windows\Favorites System\Fonts copied to Windows\Fonts System\Help copied to Windows\Help System\Programs copied to Windows\Programs AppMgr copied to Windows\AppMgr Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 151: Regedit.exe

    1 each time the PrtScrn function is activated. The command is not case-sensitive. Desktop The Thor VM3 Desktop appearance is similar to that of a desktop PC running a Windows operating system. At the bottom of the screen is the Start button. Tapping the Start Button causes the Start Menu to display.
  • Page 152: Desktop Icons

    Desktop Icons At a minimum, the desktop displays icons for My Device, Internet Explorer and the Recycle Bin. Following are a few of the other icons that may be on the Thor VM3 Desk- top. Contact Technical Assistance about the latest updates and upgrades for your oper- ating system.
  • Page 153: My Device Folders

    HTML5 Browser Lock-down menu software. Launcher Browser for web applications. Settings Access to all Control Panels, a shortcut to the Network and Dialup Control Panel and access to Taskbar options. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 154: Communication

    Windows PC Microsoft Media Player options. After the Media Player application is running, click the ? button to access Media Player Help. File Viewers The following applications are included: • JETCET PDF Viewer Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 155: Microsoft Wordpad

    There are few changes in the Windows Embedded Compact version of Remote Desktop as it relates to the general desktop Windows PC Microsoft Remote Desktop options. If installed, Remote Desktop on the Thor VM3 can be accessed by Start > Programs > Remote Desktop.
  • Page 156: Taskbar

    Tap the checkbox to have the Control Panel folders appear in drop down menu format from the Settings > Control Panel menu option. Clear Contents of Document Folder Tap the ton to remove the contents of the Document folder. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 157: Thor Vm3 Os Upgrade

    Refer to Start > Help for an explanation of standard Windows Embedded Compact task- bar icons. Following are a few of the Thor VM3 taskbar icons that may appear in the Taskbar. These icons are in addition to the Windows Embedded Compact taskbar icons.
  • Page 158: Procedure

    Maintain an uninterrupted AC/DC power source to the Thor VM3 throughout this process. • The mSATA card with the OS and systems files must be present for the Thor VM3 to boot. • Always perform OS updates when the Thor VM3 has a dependable external power source connected to the Thor VM3.
  • Page 159: Accessing The Bios Setup

    By default, the first device in the boot order is USB Hard Drive. The boot drive can also be selected at bootup. Press P5 from the Thor VM3 keypad or press F5 from an external keyboard. Use the arrows on the external keypad to make a selection.
  • Page 160: Control Panel

    Control Panel Start > Settings > Control Panel or My Device > Control Panel Tap the ? button for Help when changing Thor VM3 Control Panel options. Option Function About Software, hardware, versions and network IP. No user intervention allowed.
  • Page 161 Select a server client license from a drop down list. Licenses Volume and Sounds Enable / disable volume and sounds. Set volume parameters and assign sound WAV files to events. ZoomZone Configures screen blanking. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 162: About

    Thor VM3. The Image line displays the revision of the system soft- ware installed. Refer to the last three digits to determine the revision level.
  • Page 163 64K byte text box lim- itation. Network IP MAC Address The Network IP tab displays the MAC address of the network card(s) such as the WLAN radio and the Bluetooth module. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 164: Accessibility

    Accessibility Start > Settings > Control Panel > Accessibility Customize the way the Thor VM3 keyboard, sound, display, mouse, automatic reset and notification sounds function. There are a few changes from general Windows desktop Accessibility options. Contents Keyboard Sticky Keys - Disabled (cannot be enabled).
  • Page 165: Battery

    50%, 25%. At a point below 25% the gas gauge icon will turn red indicating the battery is low. The battery gauge icon is enabled by default, but can be disabled on the Thor VM3 Battery control panel. The UPS LED turns red when there is approximately 2 minutes of run time remaining.
  • Page 166: Bluetooth Printing

    Note: The printer can also be specified by taping the Manual button and entering the MAC address of the printer. 4. A list of available Bluetooth printers is displayed. Note: By default only printers are displayed in the search results. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 167 Dismiss the error. • Return to the Bluetooth Printing control panel and repeat the process starting with step 3. 8. The Bluetooth printer is shown. Print a test page if desired. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 168: Bluetooth Scanning

    Quick Connect Bar Code Sample Using Quick Connect with Preprinted Labels Scan the applicable bar code as indicated below: Use the LnkB bar code on either side of the Thor VM3 to connect the following scan- ners: • Honeywell/LXE 8650 family of Bluetooth ring scanners...
  • Page 169 Honeywell Granit 1911i Bluetooth scanner • Honeywell Granit 1981i Bluetooth scanner • LXE 88x0 family of Bluetooth scanners Use the bar code Quick Connect bar code on either side of the Thor VM3 to connect the following scanners: • Intermec SF51 Bluetooth scanner •...
  • Page 170 1. Select Bluetooth Scanning from the Control Panel (either large or small icon view option must be selected). 2. Tap Add Device. 3. Select Search. 4. Tap Next. 5. Select the scanner from the devices shown. 6. Tap Next. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 171: Troubleshooting

    Connect feature (depending on firmware installed). If Quick Connect does not work, use the other options to connect these scanners. • If the Honeywell Granit 1911i and Granit 1981i scanners cannot be found with the Search option, scan the PDAs/Mobility Systems Devices bar code from the scanner manual and search again.
  • Page 172: Certificates

    Start > Settings > Control Panel > Certificates Manage digital certificates used for secure communication. Note: Digital certificates are date sensitive. If the date on the Thor VM3 is incorrect, wireless authentication will fail. The Certificates stores tab lists the certificates trusted by the Thor VM3 user.
  • Page 173: Date / Time

    Date / Time Start > Settings > Control Panel > Date/Time - or - Time in Desktop Taskbar Use this Thor VM3 panel to set Date, Time, Time Zone, and assign a Daylight Savings location. Factory Default Settings Time Zone...
  • Page 174: Dialing

    Dialing Start > Settings > Control Panel > Dialing Set dialup properties for internal modems (not supplied or supported on the Thor VM3). Factory Default Settings Location Work Area Code Tone Dialing Enabled Country/Region Disable Call Waiting Disabled (blank) Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 175: Display

    Start > Settings > Control Panel > Display The display might also called the touch screen. Select the desktop background image and appearance scheme for the Thor VM3. Using the options on the Backlight tab, set the display backlight and keypad backlight timers when running on battery or external power.
  • Page 176 The default value for external power varies by the scheme selected on the Power control panel (and for Ignition Control, the status of the vehicle ignition). The default value is 1 minute when operating on the internal UPS battery. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 177: Enterprise Settings

    Keep scanner settings • Enable scanner port (On by default, see note below) Tethered Scanner (COM1) • Symbologies • Symbology Options • Scanner Settings • Scanner port Settings • Decode Security Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 178 Hardware information (no user entry) Printers Parameters Information Printer Configlet Version Memory The settings that appear in these menus depend on the printer paired with the Thor VM3. The printer must be using the Bluetooth Display Printing application. Print Engine Media...
  • Page 179 Identity information (hardware version, firmware version, OS version, etc.) (read-only) Administrator Administrator settings (name, phone, and email) Location Location settings (country, state, city, campus, and detail) Information Device Notes (read-only Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 180 Enterprise Terminal Emulation • HTML5 Browser Enterprise Browser Program Version Browser Engine General Menu Options Security Privacy Appearance Menu and Toolbar Actions HTML5 Browser Program Version General Security Privacy Appearance Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 181 Bluetooth icon in the system tray. USB Scanners When a HID enabled USB scanner is connected to the Thor VM3 the scanned data is transmitted to the active windows as keystroke messages. Any data handling to be applied to the scanned data (for example to strip leading or trailing characters) must be programmed into the scan engine.
  • Page 182: Error Reporting

    Error Reporting Start > Settings > Control Panel > Error Reporting By default, error reporting is enabled (requires Internet connection). Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 183: Input Panel

    Input Panel Start > Settings > Control Panel > Input Panel Set the current Thor VM3 keys and data input method. Factory Default Settings Input Panel Input Method Keyboard Allow applications to change input panel state Enabled Options button Keys...
  • Page 184: Internet Options

    Use LAN Disabled Autodial Name None Proxy Server Disabled Bypass Proxy Disabled Security Internet Default site Advanced Stylesheets Enabled Theming Support Enable Multimedia All options enabled Security All options enabled Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 185 Security Tab: Use the Settings button to set ActiveX control, scripting and plug-in behavior for each zone (Internet, Local Intranet, Trusted Sites, Restricted Sites). Use the Site button to add sites to each zone. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 186: Keyboard

    Start > Settings > Control Panel > Keyboard Set keypad key map, keypad key repeat delay, and key repeat rate. Factory Default Settings Repeat character Enable Repeat Delay Short Repeat Rate Slow Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 187: Keyboard Remapper

    Keys Keyboard Remapper is designed to remap keys on the integrated keypad (P1 thought P7) or keys on an attached USB keyboard (such as the Honeywell 21-key numeric key- board). If programming both the integrated programmable keys and keys on a USB keyboard, follow the process below.
  • Page 188 5. If the import is not successful (i.e.: an invalid file name or location was specified) an error message is displayed. Otherwise the keymap has been exported. Restore Defaults Tap Restore Defaults to apply the default values for all keys. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 189 For example, if the integrated programmable keys on the Thor VM3 were remapped then a USB keyboard was attached only they remapped keys on the USB keyboard would be reset to default values. Remove the USB keyboard and relaunch the remapper utility to restore defaults to the integrated programmable keys.
  • Page 190: Mixer

    Mixer Start > Settings > Control Panel > Mixer The Thor VM3 has two speakers (located at the bottom front of the unit) and one micro- phone (located at the top front of the unit). Use the settings on these panels to adjust the master volume, record gain and sidetone.
  • Page 191 Use the radio buttons to enable or disable the sidetone. Tap and hold the Record Gain or Sidetone sliders and move either left or right, or tap the left and right arrows, to adjust the levels. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 192: Mouse

    Mouse Start > Settings > Control Panel > Mouse Use this option to set the double-tap sensitivity for stylus taps on the Thor VM3 touch screen. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 193: Network And Dialup Connections

    Network and Dialup Connections Start > Settings > Control Panel > Network and Dialup Connections Set Thor VM3 network driver properties and network access properties. Select a con- nection to use, or create a new connection. Create a New Connection 1.
  • Page 194 You can activate the connection by double-tapping on the specific connection icon in the Remote Networking window, but this will only start an RAS (Remote Access Ser- vices) session, and does not start ActiveSync properly. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 195: Network Capture

    If the log file is stored in \System, all previous data is saved across the warmboot. • If Netlog is enabled across the warmboot, a series of brief popups may be displayed during the boot cycle. No user interaction is required. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 196 3. Select options from the Commands list, enter the new packet size in the Options list and click the Run cmd button. NDISLog NDISLog creates a .TXT file that can be viewed with any text editor program that sup- ports .TXT files. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 197 Stops logging network traffic. file Specifies the name of the file to which NDISLog information is stored. Save File Stores the file name. Run cmd Performs the selected start or stop command. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 198: Options

    Options Start > Settings > Control Panel > Options It may be necessary to warmboot the Thor VM3 after making desired changes. A pop up window indicates if a warmboot is required. Communication Options on this tab configure communication options for the Thor VM3.
  • Page 199 Note: If the touch screen is disabled on a Thor VM3, you must use a USB mouse or keyboard attached to the Thor VM3 to access this tab to re-enable the touch screen unless a key has...
  • Page 200 Check this box to enable it. It is recommended that the Wakeup Timer be enabled. Screen Resolution By default screen resolution is set to 1024x768. A restart is required to change resolu- tion. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 201: Owner

    Owner Start > Settings > Control Panel > Owner Set the Thor VM3 owner details. The Network ID is used when logging into a remote net- work. Factory Default Settings Identification Name Blank Company Blank Address Blank Telephones Blank Display owner ID at power-on...
  • Page 202 Enter user name, password and domain to be used when logging into network resources. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 203: Password

    Check the box to enable the password, enter a timeout and select a password type. Enter the password in the Password text box, then press Tab and type the password again to confirm it. A changed/saved password is in effect immediately. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 204 Hint Use this screen to enter a hint in case the password is forgotten. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 205: Pc Connection

    Tap the Change button to change the direct connect setting. Tap the drop-down box to view a list of preconfigured connection settings. The Thor VM3 does not support a USB client connection. ActiveSync is only available via serial connection. In order to use a serial port for ActiveSync, the port must be disabled in...
  • Page 206: Peripherals

    Tap the Test button to determine the presence of the defroster. Use this button when the front panel of the Thor VM3 has been swapped. For example, if the Thor VM3 did not contain a defroster but a new front panel with a defroster is installed, tap the Test but- ton to update the defroster presence status on this tab.
  • Page 207: Power

    The Display > Backlight setting is synchronized with the User Idle setting in the Schemes tab in the Power control panel. Factory Default Settings The default Power Scheme selected for the Thor VM3 depends on: • if external power is connected to the Thor VM3, •...
  • Page 208 UPS Power Scheme is used. This Power Scheme has much shorter timeout values designed to shut down the Thor VM3 before the UPS battery is depleted. Because of the cumulative effect, if the Thor VM3 is operating from the UPS, for exam- ple: •...
  • Page 209: Power Configuration Mode

    AC/DC Mode This is the default power mode. In AC/DC mode the Thor VM3 is turned On when power is connected. Ignition input is ignored when AC/DC Mode is enabled.
  • Page 210 Note: When the UPS battery has been depleted or disconnected (the Thor VM3 is first powered out of the box, the front panel has been replaced, etc.) power the Thor VM3 manually by pressing the power button. After the initial power up, the Thor VM3 powers on automatically when the Ignition Control Mode is enabled and the ignition is turned on.
  • Page 211 Ignition switched to Active. An example of this case would be a Thor VM3 that is running on UPS and is then mounted on a dock that has truck power and the ignition switch is already On.
  • Page 212 The Thor VM3 boots and follows the UPS power scheme with power management tim- ers reset at boot up. Conditions The Thor VM3 is Off and the power button is pressed the Thor VM3 and at least one of the following conditions are met: •...
  • Page 213: Regional Settings

    Start > Settings > Control Panel > Regional Settings Set the appearance of numbers, currency, time and date based on regional and lan- guage settings. Set the Thor VM3 user interface language and the default input lan- guage. Factory Default Settings...
  • Page 214: Registry

    Note: When the Thor VM3 is set to user defaults, a second reboot must be performed to load the WLAN driver. When the Thor VM3 has finished booting, return to the Registry panel and tap Restart,...
  • Page 215: Remove Programs

    Files stored in the My Documents folder are not removed using this option. Note: Do not remove factory installed programs using this option. Contact Technical Assistance if factory installed programs must be deleted. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 216: Screen Control

    Note: There is no default value for Ambient Light % as it varies depending on the level of light where the Thor VM3 is located. If the Thor VM3 has an indoor display it does not have an ambient light sensor and the Ambient Light % is always 0.
  • Page 217: Storage Manager

    Start > Settings > Control Panel > Storage Manager Installed storage devices are listed by device name in the drop-down box. To view infor- mation about the disk or perform store operations, select a device from the list. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 218: Stylus

    Press the Enter key to keep the new calibration setting or press the Esc key to revert to the previous calibration settings. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 219: System

    128 MB may only report 99 MB memory, since 29 MB is used by the operating system. This is actual DRAM memory, and does not include internal flash used for storage. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 220: Device Name

    The device name and description can be changed by the user. Enter the name and description using either the keypad or the Input Panel and tap OK to save the changes. This information is used to identify the Thor VM3 to other computers and devices. Copyrights This screen is presented for information only.
  • Page 221: Terminal Server Client Licenses

    Terminal Server Client Licenses Start > Settings > Control Panel > Terminal Server Client Licenses Any licenses stored on the Thor VM3 appear in the drop-down list. Select a license and tap the Close button. The license is available for use immediately.
  • Page 222: Volume And Sounds

    You can also select / deselect sounds for key clicks and screen taps and whether each is loud or soft. As the volume scrollbar is moved between Loud and Soft, the Thor VM3 emits a tone each time the volume increases or decreases.
  • Page 223 GOOD.WAV and SCANBAD.WAV. These are unprotected WAV files and can be replaced by a WAV file of the user’s choice. By default a good scan sound on the Thor VM3 is a single beep, and a bad scan sound is a double beep.
  • Page 224: Zoomzone

    Motion Detection Method Select the motion detection method. The Thor VM3 supports the screen blanking box to determine motion. Select the port (COM1 or COM2) to which the blanking box is attached. Note: By default, COM1 and COM2 ports are used by Enterprise Data Collection. To use a COM...
  • Page 225 Set Zoom Area The ZoomArea can be selected from the current active desktop display. To set the zoom area: 1. Display the desired content on the Thor VM3 desktop. 2. Open the ZoomZone interface. 3. Tap the Set Zoom Area button.
  • Page 226 When finished, at the top of the display tap File > Exit to exit. Test Zoom Area Tap the Test Zoom Area button. The zoom image is displayed. When finished, at the top of the display tap File > Exit to exit. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 227: Automatic Firmware Update Utility

    UpdateFW.tag - The file that triggers the update utility to begin. Be sure to copy this file only after the .cab file has been copied. As soon as the Thor VM3 detects the presence of this file, the unit reboots in five seconds.
  • Page 228: Configuration Cloning Utility (Ccu)

    This utility provides an automated process to read the configuration settings from one Thor VM3 and then apply those settings to one or more other Thor VM3s with the same operating system. The Configuration Cloning Utility (CCU) is installed as part of the fac- tory software load.
  • Page 229: Menu Options

    CCU . ccf files are encrypted for security. Once a ccf file is created on one Thor VM3 it can be copied to other Thor VM3s to duplicate the configuration. An existing ccf file can be opened, modified, applied to the Thor VM3, saved, saved with a different name, etc.
  • Page 230 Tap No to apply the values from the ccf file and leave all other parameters as-is on the destination device. • Tap Cancel to exit with no changes to the destination device. Upon completion, exit the CCU and reboot the Thor VM3 so changes can take effect. User Selects the desired user access level: •...
  • Page 231 Pull-down list - A down arrow indicates the setting must be selected from a pull-down list of available values. Expand the list and select the desired setting from the list of options. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 232 Thor VM3. If the parameter setting changes should also be applied to this Thor VM3, select Regis- try > Import Settings. After importing the settings, a reboot is necessary for the changes to take effect on the Thor VM3.
  • Page 233 5. Tap Registry > Apply settings 6. Reboot the Thor VM3 for the new settings to take effect. 7. The ccf file can be used to configure another Thor VM3. See Example 4. Example 4: Clone settings to another device 1.
  • Page 234 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 235: Chapter 6 - Activesync

    ActiveSync with Windows Mobile Device Center. Using Microsoft ActiveSync, you can synchronize information on your desktop com- puter with the Thor VM3 and vice versa. Synchronization compares the data on your mobile device with your desktop computer and updates both with the most recent data.
  • Page 236: Initial Setup

    ActiveSync wizard. For more information about using ActiveSync on your desktop com- puter, open ActiveSync, then open ActiveSync Help. Initial Setup The Thor VM3 supports ActiveSync over a serial port. The Thor VM3 does not support a USB ActiveSync connection. Connect via Serial Port In order to use a serial port for ActiveSync: •...
  • Page 237: Configure Pc Connection Settings

    3. Verify that pane says Connect using ‘ActiveSync’. If necessary, tap the Change button to select the correct setting. Note: Do not use USB as this option is not supported on the Thor VM3. 4. Click OK to confirm settings and close the open window.
  • Page 238: Start The Activesync Connection

    9. On the Thor VM3, select Start > Run and type in the repllog.exe command and press Enter. Note: Do not use the ActiveSync link on the Thor VM3 desktop as this link attempts to connect to a server to synchronize emails.
  • Page 239: Reset And Loss Of Host Re-Connection

    ActiveSync Help ActiveSync on the host says that a device is trying to connect, but it cannot identify it Verify the cable is attached to the Thor VM3. Disconnect and reconnect the cable from the PC. Check that the correct connection is selected.
  • Page 240 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 241: Chapter 7 - Wireless Network Connections

    CHAPTER WIRELESS NETWORK CONNECTIONS Managing Wireless Connections The Thor VM3 has an 802.11 a/b/g/n WLAN radio and an optional WWAN radio. • The WLAN radio is configured using the WLAN Wireless Configuration Utility (WCU). • The WWAN radio is configured using the VM3 WWAN Connection Manager.
  • Page 242: Important Notes

    Important Notes It is important that all dates are correct on the Thor VM3 and host computers when using any type of certificate. Certificates are date sensitive and if the date is not cor- rect authentication will fail. When using the 802.11 radio, the U-NII 1 band is the preferred band for indoor oper- ation.
  • Page 243: Tasks

    All profiles that have been created are listed in this section. Profiles can be configured for auto connect or manual connect and are subdivided by connection type in this list. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 244: Admin Login

    The appearance of the icon indicates if the admin is logged in or not. To log in: 1. Tap the Admin Login icon. 2. Enter the password. The default password is Honeywell. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 245: Browse Nearby Wireless Networks

    Signal - A graphic representation of the signal strength plus (0 to 4 bars) plus a text description of signal strength. • Radio Type - The type of radio in the access point, i.e. 802.11a, 802.11g, etc. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 246: Creating A Profile

    4. Change the profile name if desired. 5. Tap Advanced security settings for additional configuration options including Security. 6. Tap OK to exit and save the profile or type Cancel to exit without creating a profile. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 247: Advanced Profile Configuration

    The options available on the security tab will depend on the security type and encryp- tion type selected. Review the appropriate section for configuring the WCU for network security: • Open (No Security) • • WPA2-Personal • PEAP-TLS • PEAP-MSCHAP Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 248 • PEAP-GTC • LEAP • EAP-FAST PEAP • EAP-FAST TLS • EAP-TLS • EAP-TTLS Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 249 1. Set Security Type to No authentication (Open). 2. Set Encryption Type to none. 3. Tap OK. 4. From the profile listing, make sure the desired profile is active. 5. Verify the connection using Status. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 250 3. Enter the Network Security Key. 4. Select the Key Index. 5. Tap OK. 6. From the profile listing, make sure the desired profile is active. 7. Verify the connection using Status. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 251 2. Set Encryption Type to AES. 3. Enter the Network Security Key. 4. Tap OK. 5. From the profile listing, make sure the desired profile is active. 6. Verify the connection using Status. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 252 3. Set network authentication method to Protected EAP (PEAP). 4. Tap the Settings button. 5. Select the Connection tab. 6. Select Validate server certificate. 7. Select the trusted root certificate from the listed certificates. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 253 12. Select EAP-TLS as the authentication method. 13. Tap OK to close any open windows. 14. From the profile listing, make sure the desired profile is active. 15. Verify the connection using Status. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 254 3. Set network authentication method to Protected EAP (PEAP). 4. Tap the Settings button. 5. Select the Connection tab. 6. Select Validate server certificate. 7. Select the trusted root certificate from the listed certificates. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 255 12. Select EAP-MSCHAPv2 as the authentication method. 13. Tap OK to close any open windows. 14. From the profile listing, make sure the desired profile is active. 15. Verify the connection using Status. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 256 3. Set network authentication method to Protected EAP (PEAP). 4. Tap the Settings button. 5. Select the Connection tab. 6. Select Validate server certificate. 7. Select the trusted root certificate from the listed certificates. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 257 11. Select EAP-GTC as the authentication method. 12. Tap OK to close any open windows. 13. From the profile listing, make sure the desired profile is active. 14. Verify the connection using Status. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 258 6. If saved username and password is selected, enter the credentials now. 7. The About tab provides Cisco copyright information. 8. Tap OK to close all open windows. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 259 Note: If the credentials are not entered when to window first pops up, the credentials window can become hidden behind other windows. 11. Verify the connection using Status. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 260 To configure for Cisco EAP-FAST PEAP: 1. Set Security Type to WPA2-Enterprise or CCKM. 2. Set Encryption Type to AES. 3. Set network authentication method to CISCO-FAST. 4. Tap the Settings button. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 261 7. If saved username and password is selected, enter the credentials now. 8. Tap the Authentication tab. 9. Select the desired authentication method. Any of the available options may be used. 10. The About tab provides Cisco copyright information. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 262 Note: If the credentials are not entered when to window first pops up, the credentials window can become hidden behind other windows. 14. Verify the connection using Status. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 263 To configure for Cisco EAP-FAST TLS: 1. Set Security Type to WPA2-Enterprise or CCKM. 2. Set Encryption Type to AES. 3. Set network authentication method to Cisco:EAP-FAST. 4. Tap the Settings button. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 264 8. The About tab provides Cisco copyright information. 9. Tap OK to close all open windows. 10. From the profile listing, make sure the desired profile is active. 11. Verify the connection using Status. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 265 4. Tap the Settings button. Note: If a user certificate has already been selected, the details would be populated on this screen. 5. Tap Select to select a user certificate on this computer. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 266 8. The selected certificate is displayed. 9. Tap OK to close any open windows. 10. From the profile listing, make sure the desired profile is active. 11. Verify the connection using Status. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 267 1. Set Security Type to WPA2-Enterprise or CCKM. 2. Set Encryption Type to AES. 3. Set network authentication method to EAP_TTLS. 4. Tap the Settings button. 5. Select the Connection tab. 6. Select Validate server certificate. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 268 Note: If the credentials are not entered when to window first pops up, the credentials window can become hidden behind other windows. 14. Verify the connection using Status. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 269: Roam Management

    Roam Management General The general tab provides information on the current connection. There are no user entries on this screen. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 270 Default -65 dBm, range is -80 to -55. Probe Request Interval The interval between roam probes. Default 5 seconds, range is 5 to 60. (sec) CCX Control Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 271 (MCS0 to MCS15). MCS0 (Modulation and Coding Scheme) 0 is slowest, MCS15 is fastest but subject to more errors. Default is disabled. Note: DataRate selection is reset to default (Disabled) after reboot. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 272 Diversity By default, diversity is on. Selection Adapter The adapter tab provides information on the radio card. There are no user entries on this screen. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 273: Advanced Settings

    After the client authenticates with one access point, it can roam to others under the same controller by handshaking rather than authentication. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 274: Certificates

    Note: Please refer to the Security Primer to prepare the Authentication Server and Access Point for communication. Note: It is important that all dates are correct on the Thor VM3 and host computers when using any type of certificate. Certificates are date sensitive and if the date is not correct authentication will fail.
  • Page 275 Click the Download a CA certificate, certificate chain or CRL link. Make sure the correct root CA certificate is selected in the list box. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 276 To download the CA certificate, click on the Download CA certificate link. Click the Save button and save the certificate. Make sure to keep track of the name and location of the certificate. Install the certificate on the Thor VM3. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 277: Install A Root Ca Certificate

    Install a Root CA Certificate Copy the certificate file to the Thor VM3. Import the certificate by navigating to Start > Control Panel > Certificates. Tap the Import button. Make sure From a File is selected and tap OK. Using the explorer buttons, browse to the location where you copied the certificate, select the certificate desired and tap OK.
  • Page 278: Generate A User Certificate

    This process saves a user certificate and a separate private key file. Windows Embedded Compact equipped devices such as the Thor VM3 require the private key to be saved as a separate file rather than including the private key in the user certificate.
  • Page 279 Click on the Create and submit a request to this CA link. For the Certificate Template, select User. Check the Mark keys as exportable and the Export keys to file checkboxes. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 280 When prompted for the private key password: • Click None if you do not wish to use a password, or • Enter and confirm your desired password then click OK. Click the Download certificate link. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 281: Install A User Certificate

    AAAUSER.CER. Install the user certificate. Install a User Certificate Copy the certificate and private key files to the Thor VM3. Import the certificate by navi- gating to Start > Control Panel > Certificates. Select My Certificates from the pull-down list.
  • Page 282 If the private key is present, the process is complete. • If the private key is not present, import the private key. To import the private key, tap OK to return to the Certificates screen. Tap import. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 283 Make sure the certificate and private key file have the same name, for example AAAuser.cer for the certificate and AAAuser.pvk for the private key file. If the file names are not the same, rename the private key file and import it again. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 284: Vm3 Wwan Connection Manager

    WWAN carriers, the connection manager must load carrier firmware and this can take several minutes. Connection troubleshooting: • If there is a connection issue, the first step in troubleshooting is to verify the APN on Connection Type tab. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 285: Home

    The active connection displays the IP address and signal strength (RSSI). Inactive con- nections show the status as Standby. If a WWAN connection is active, the roaming status (Home or Roam) is displayed. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 286: Link Settings

    (WCU). The WWAN networks, if any, are shown on this page. A WWAN network is only displayed if a SIM card has been installed for that network. The Thor VM3 supports two SIM cards. Install SIM Card(s) for SIM card installation instructions. A WWAN network can be enabled or disabled from this screen, however the connection is configured by tapping the applicable Network Settings button.
  • Page 287 To configure a WWAN network, tap the View Network Settings button. To configure the WLAN connection use the WLAN Wireless Configuration Utility (WCU). Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 288 An APN mismatch may generate an error message, however this is not always the case. The first step in diagnosing a connection error should be to verify the APN. After all entries are completed, tap the Save button. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 289 Next select the PIN/PUK tab. Note that the SIM card being configured (Sim1 or Sim2) is identified at the top of this tab. Enter the PIN or PUK and tap Save then tap Exit to return to the Connection Manager. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 290: System Settings

    Connected Not connected This icon is in addition to the connection icon in the system tray. By default the on-screen icon is disabled. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 291 The WWAN card supports firmware update over the air (Firmware Over The Air, or FOTA). By default, FOTA is disabled. See Using FOTA Restore Defaults Use this option to return all Connection Manager settings to the default value. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 292 Honeywell recommends distributing firmware via a WLAN connection rather than the WWAN connection. This requires an HTTP server which can be hosted on the Internet or the same Intranet (i.e.: the same network domain) as the Thor VM3. Honeywell tested FOTA using: •...
  • Page 293 5. Click on the Apache tab and select Access and Passwords > Folder www access and passwords. 6. Select Password Disabled and Local, Intranet and Internet Access. 7. Verify server setup: • Ping the sever from the Thor VM3 to verify connectivity between the devices. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 294 • Open the web browser on the Thor VM3 and verify the URL of the server can be accessed. Load Firmware Updates The firmware update is provided by Honeywell customer support. The update consists of a version string and a zip file. The version string is three numbers separated by peri- ods, i.e.: 1.0.0 or 3.1.12.
  • Page 295: Gps

    Tap the Start button to begin receiving GPS data. Once started, the button label changes to Stop and GPS data on screen is populated. Tap the Clear GPS Data button to erase the GPS data. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 296: About

    About The about screen has no user-configurable parameters. It identifies the firmware and hardware versions, the carrier selected, MEID, etc. for the WWAN radio. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 297: Appendix A - Key Maps

    CHAPTER KEY MAPS Integrated Keypad There are seven integrated programmable keys located on the Thor VM3 below the dis- play. Each programmable key can be modified by the Orange key for a total of 14 pro- grammable keys. Keyboard Remapper to remap these keys.
  • Page 298 Default Key Value Increase display brightness Blue Increase display brightness Decrease display brightness Blue Decrease display brightness The Blue plus P3, P4 or P7 key press sequences cause no action. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 299: External 21-Key Keyboard

    • Pressing the backlight key (alone or after the Green or Yellow keys) cycles the keypad backlight through Low, Medium, High, Off then repeats. Yellow- Green- Non-Shifted Shifted Shifted Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 300 Yellow- Green- Non-Shifted Shifted Shifted Programmable Programmable Delete Backspace Backtab Left Left Left Left Right Right Right Right Down Down Down Down Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 301: External 95-Key Keyboard

    95-key PS/2 Keyboard. The key map table that follows lists the commands used for the Thor VM3. Note that since the Thor VM3 uses a Microsoft Windows operating system, no DOS Terminal Emulation keypress sequences are provided. There are 10 hidden keys on the 95 key keyboard. Each of the hidden keys is accessed by pressing the ...
  • Page 302: External 60-Key Keyboard

    The 2nd functions of the F4 and F5 keys are not used as the display brightness is adjusted via the buttons on the front of the Thor VM3. • The 2nd functions of the F6 and F7 keys are not used as the Thor VM3 has TFT LCD screen with no provision for contrast adjustments. •...
  • Page 303 Down Arrow Right Arrow Right Arrow Left Arrow Left Arrow Insert Bksp Delete (numeric) Home Left Arrow Right Arrow Page Up Up Arrow Page Down Down Arrow ScrollLock Shift Shift Shift Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 304 To get this Key / Press These Keys in this Order Function Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 305 / (numeric) Ctrl / (alpha) - (numeric) Ctrl - (alpha) + (numeric) Ctrl + (alpha) * (numeric) I (letter i) * (alpha) Ctrl I (letter i) : (colon) ; (semicolon) Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 306 To get this Key / Press These Keys in this Order Function _ (underscore) , (comma) ' (apostrophe) ~ (tilde) " & Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 307: Appendix B - Specifications And Reference Material

    Minimum loudness greater than 95dBm at 10 cm in front of unit Power Supply 10 to 60 VDC isolated Uninterruptible Power Supply Internal UPS battery, 30-minute life at -30°C (-22°F) Backup Battery (RCT) Internal lithium battery maintains Real Time Clock Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 308: Vm1D Standard Dock

    External Power Supply 50-150 VDC DC power supply available for vehicles over 60 VDC Note: Use dock VMX005VMCRADLE (VMXD Enhanced Dock of Off-Vehicle Use) in AC power applications. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 309: Vm3D Enhanced Dock

    9-pin female, USB connector supports USB host port via adapter cable Note: USB Client port may not be supported by the Thor VM3 operating system. USB 2 Connector 15-pin female, USB connector supports 2 USB host ports via adapter cable...
  • Page 310: Vmxd Enhanced Dock

    9-pin female, USB connector supports USB host port via adapter cable Note: USB Client port may not be supported by the Thor VM3 operating system. USB 2 Connector 15-pin female, USB connector supports 2 USB host ports via adapter cable...
  • Page 311: Vmxd Enhanced Dock For Off-Vehicle Use (Qm3Ac)

    9-pin female, USB connector supports USB host port via adapter cable Note: USB Client port may not be supported by the Thor VM3 operating system. USB 2 Connector 15-pin female, USB connector supports 2 USB host ports via adapter cable...
  • Page 312: Dimensions

    Note: The RAM ball is not included in the following measurements. Length 7.1” (18.0 cm) Width 6.1” (15.5 cm) Height 2.1” (5.4 cm), measurement includes strain relief cable clamps Weight 2.4 lb. (1.1 kg) Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 313: Environmental Specifications

    -22°F to 140°F (-30°C to 60°C) [non-condensing] Operating Humidity Up to 95% Water and Dust IEC 60529 compliant to IP66 15 kV air, 8kV direct contact Vibration MIL-STD-810F, composite wheeled vehicles. Crash SAE-J 1455 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 314: Network Card Specifications

    Operating Frequency 2.402 - 2.480 GHz QDID B013455 WWAN Device Software definable (data only), includes GPS Technology 4G radio: LTE/UMTS/HSPA+/GSM/GPRS/EDGE/ EV-DO Supports 2 SIM cards for hyper-roaming between WWAN carriers Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 315: Port And Connector Pinouts

    Screen Blanking Box - The white wire in the power cable must be connected to the unswitched side of the screen blanking box. See applicable wiring diagram below. Cable shell provides chassis ground connection. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 316 VMXD enhanced dock for off-vehicle use requires adapter cable VM1076CABLE to con- nect the dock to the AC/DC adapter. This cable is included in the AC kit for off-vehicle use. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 317: Com1 And Com2 Connector

    USB host 1; 5V output power PIN 9 PIN 6 Common ground Common ground USB_H1_D+ USB host 1 data signal USB_H1_D- USB host 1 data signal USBC_VBUS USB client 5V detect from attached host Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 318: D9 Male Connector

    PIN 4 USB_H1_D- USB D- PIN 1 USB_H1_D+ USB D+ USB Power Return Shell CGND Chassis Ground USB Client Connector The USB client connection is not supported on the Thor VM3. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 319: Usb2 Connector

    USB host 2 data signal Common ground Common ground USB_H3_PWR USB host 3 5V output power USB_H3_D+ USB host 3 data signal USB_H3_D- USB host 3 data signal Common ground Common ground Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 320 Common ground Common ground USB Host Connectors Signal Description 5V_USB USB Power, Current Limited PIN 4 USB_H2_D- USB D- PIN 1 USB_H2_D+ USB D+ USB Power Return Shell CGND Chassis Ground Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 321 PS/2 to USB Keyboard Adapter Cable Note: This cable is not supported when the Thor VM3 is used with the VM1D Standard Dock. D9 Male Connector - USB Signal Description Not Used PIN 5 PIN 1 Not Used Not Used...
  • Page 322: Canbus / Audio Connector

    Audio output Headset output Mic input Microphone input Mic return Microphone return Audio Return Optional ground CAN_SHLD CAN_H CAN_H bus line dominant high CAN reserved CAN_V+ Option CAN external Power Supply Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 323: Headset Adapter Cable

    Not used Not used Quick Connect Headset Connector Signal Description Mic input Microphone input PIN 4 Mic return Microphone return Audio output Headset output PIN 1 Audio return Headset return Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 324 J1939 Female J1939 Male CAN_V+ Option CAN external Power Supply CAN_H CAN_H bus line dominant high CAN_L CAN_L bus line dominant low CAN_SHLD Not used Not used Not used Not used Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 325: Hat Encoding

    Hat Encoding Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 326 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 327: Licenses Of Third Party Software

    Licenses of Third Party Software This product contains software provided by third parties, which may include the below listed components. The Honeywell product that includes this file does not necessarily use all of the third party software components referred to below.
  • Page 328 "recipients" may be individuals or organizations. To "modify" a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 329 The "Corresponding Source" for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 330 11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures. When you convey a covered work, you waive any legal power to forbid Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 331 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 332 Corresponding Source, you remain obligated to ensure that it is available for as long as needed to satisfy these requirements. e) Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and Corresponding Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 333 (and with an implementation available to the public in source code form), and must require no special password or key for Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 334 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 335 However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 336 In the following three paragraphs, a "patent license" is any express agreement or commitment, however denominated, not to enforce a patent Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 337 If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 338 APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 339 This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 340 As used herein, "this License" refers to version 3 of the GNU Lesser General Public License, and the "GNU GPL" refers to version 3 of the GNU General Public License. "The Library" refers to a covered work governed by this License, Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 341 (ten or fewer lines in length), you do both of the following: Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 342 GNU GPL, and only to the extent that such information is necessary to install and execute a modified version of the Combined Work produced by recombining or relinking the Application with a modified version of the Linked Version. (If Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 343 Library. Package(s) using Boost regex library License ============================ * The Boost C++ Libraries Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 344 Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 345 General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 346 0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 347 The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 348 GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 349 Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 350 Library" must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 351 You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 352 License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 353 To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 354 License Text (OpenSSL (Cisco EAP Security) License) -------------------------- LICENSE ISSUES ============== The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 355 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 356 * 4. If you include any Windows specific code (or a derivative thereof) from * the apps directory (application code) you must include an acknowledgement: * "This product includes software written by Tim Hudson ([email protected])" Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 357 1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 358 Contributor, the initial code and documentation distributed under this Agreement, and b) in the case of each subsequent Contributor: i) changes to the Program, and Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 359 Contributors all liability for damages, including direct, indirect, special, incidental and consequential damages, such as lost profits; Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 360 LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OR DISTRIBUTION OF THE PROGRAM OR THE EXERCISE OF ANY RIGHTS GRANTED HEREUNDER, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 361 * Copyright (c) 1998 CORE SDI S.A., Buenos Aires, Argentina. * All rights reserved. Redistribution and use in source and binary * forms, with or without modification, are permitted provided that * this copyright notice is retained. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 362 The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 363 * Neither the name of ekus.net nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 364 "Work" refers to the collection of files distributed by the Publisher, including the Source Code, Executable Files, binaries, data files, documentation, whitepapers and the Articles. "You" is you, an individual or entity wishing to use the Work and exercise your rights under this License. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 365 PUNITIVE OR EXEMPLARY DAMAGES ARISING OUT OF THIS LICENSE OR THE USE OF THE WORK OR OTHERWISE, EVEN IF THE AUTHOR OR THE PUBLISHER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Termination. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 366 1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 367 “NOTICE SPECIFIC TO SOFTWARE AVAILABLE ON THIS WEB SITE.” If you use such code (the “software”), you accept this license. If you do not accept the license, do not use the software. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 368 ============================ * blowfish License Text (blowfish License) -------------------------- // blowfish.cpp C++ class implementation of the BLOWFISH encryption algorithm // _THE BLOWFISH ENCRYPTION ALGORITHM_ // by Bruce Schneier // Revised code--3/20/94 Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 369 (a) that the initial Contributor has attached the notice described in Exhibit B to the Covered Software; or (b) that the Covered Software was made available under the terms of Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 370 You. For purposes of this definition, "control" means (a) the power, direct or indirect, to cause the direction or management of such entity, Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 371 This License does not grant any rights in the trademarks, service marks, or logos of any Contributor (except as may be necessary to comply with the notice requirements in Section 3.4). Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 372 License, or sublicense it under different terms, provided that the license for the Executable Form does not attempt to limit or alter the recipients' rights in the Source Code Form under this License. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 373 Software under this License. Except to the extent prohibited by statute or regulation, such description must be sufficiently detailed for a recipient of ordinary skill to be able to understand it. 5. Termination -------------- Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 374 * essential part of this License. No use of any Covered Software is * * authorized under this License except under this disclaimer. ************************************************************************ ************************************************************************ * 7. Limitation of Liability * -------------------------- * Under no circumstances and under no legal theory, whether tort Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 375 10.2. Effect of New Versions You may distribute the Covered Software under the terms of the version of the License under which You originally received the Covered Software, Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 376 You may add additional accurate notices of copyright ownership. Exhibit B - "Incompatible With Secondary Licenses" Notice --------------------------------------------------------- This Source Code Form is "Incompatible With Secondary Licenses", as defined by the Mozilla Public License, v. 2.0. Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide...
  • Page 377: Appendix C - Thor Vm3 Agency Information

    Label Locations Compliance labels are located in the dock well area on the back of the Thor VM3, as indicated by the shaded areas below. The Thor VM3 must be removed from the dock to view the labels.
  • Page 378 Honeywell 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com ™ VM3-WEC-UG Rev E 9/17...

Table of Contents