Available languages
Available languages
Quick Links
DEH-P6800MP
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.
Printed in Thailand
Imprimé en Thaïlande
Connecting the Units
Note:
• This unit is for vehicles with a 12-volt battery and
• When an external power amp is being used with
negative grounding. Before installing it in a recre-
this system, be sure not to connect the blue/white
ational vehicle, truck, or bus, check the battery
lead to the amp's power terminal. Likewise, do not
voltage.
connect the blue/white lead to the power terminal
• To avoid shorts in the electrical system, be sure to
of the auto-antenna. Such connection could cause
disconnect the ≠ battery cable before beginning
excessive current drain and malfunction.
installation.
• To avoid a short-circuit, cover the disconnected
• Refer to the owner's manual for details on
lead with insulating tape. Insulate the unused
connecting the power amp and other units, then
speaker leads without fail. There is a possibility of
make connections correctly.
a short-circuit if the leads are not insulated.
• Secure the wiring with cable clamps or adhesive
• To prevent incorrect connection, the input side of
tape. To protect the wiring, wrap adhesive tape
the IP-BUS connector is blue, and the output side
around them where they lie against metal parts.
is black. Connect the connectors of the same
colors correctly.
• Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake and
• If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
seat rails. Do not route wiring in places that get
switch, the red lead of the unit should be connected
hot, such as near the heater outlet. If the insulation
to a terminal coupled with ignition switch ON/OFF
of the wiring melts or gets torn, there is a danger of
operations. If this is not done, the vehicle battery
the wiring short-circuiting to the vehicle body.
may be drained when you are away from the vehi-
• Don't pass the yellow lead through a hole into the
cle for several hours. (Fig.1)
engine compartment to connect to the battery. This
will damage the lead insulation and cause a very
dangerous short.
• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.
• When replacing the fuse, be sure to only use a fuse
ACC position
No ACC position
of the rating prescribed on this unit.
• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
the left and right ≠ speaker leads are common.
• Speakers connected to this unit must be high-
• The black lead is ground. Please ground this lead
power with minimum rating of 50 W and imped-
separately from the ground of high-current prod-
ance of 4 to 8 ohms. Connecting speakers with out-
ucts such as power amps.
put and/or impedance values other than those
If you ground the products together and the ground
noted here may result in the speakers catching fire,
becomes detached, there is a risk of damage to the
emitting smoke or becoming damaged.
products or fire.
• When this product's source is switched ON, a con-
trol signal is output through the blue/white lead.
• Cords for this product and those for other products
Connect to an external power amp's system remote
may be different colors even if they have the same
control or the car's Auto-antenna relay control ter-
function. When connecting this product to another
minal (max. 300 mA 12 V DC). If the car features
product, refer to the supplied manuals of both
a glass antenna, connect to the antenna booster
products and connect cords that have the same
power supply terminal.
function.
7 When not connecting a rear speaker lead to a Subwoofer
Antenna jack
15 cm (5-7/8 in.)
Front output
This product
Subwoofer output
Jack for the Wired Remote Control
Please see the Instruction Manual for the
Wired Remote Control (sold separately).
Yellow/black
If you use an equipment with Mute function, wire this
lead to the Audio Mute lead on that equipment. If not,
keep the Audio Mute lead free of any connections.
Yellow
To terminal always supplied with power regardless of
ignition switch position.
Fig. 1
Red
To electric terminal controlled by ignition switch (12
V DC) ON/OFF.
Orange/white
To lighting switch terminal.
Black (ground)
To vehicle (metal) body.
With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.
Perform these connections when using the
optional amplifier.
Connecting cords with RCA pin
plugs (sold separately)
Rear output
16 cm (6-1/4 in.)
IP-BUS input (Blue)
Fuse
(10 A)
Multi-CD player
IP-BUS cable
(sold separately)
Blue/white
To system control terminal of the power amp or
Auto-antenna relay control terminal (max. 300
mA 12 V DC).
System remote control
+
Front speaker
≠
White
+
Front speaker
≠
White/black
Gray/black
Left
Green
+
Rear speaker
≠
Green/black
Violet/black
+
Rear speaker
≠
+
Subwoofer
≠
Power amp
(sold separately)
Power amp
(sold separately)
Power amp
(sold separately)
+
Front speaker
≠
Gray
+
Front speaker
≠
Right
Violet
+
Rear speaker
≠
+
Rear speaker
≠
+
Subwoofer
≠
Fig. 2
Related Manuals for Pioneer DEH P6800MP
Summary of Contents for Pioneer DEH P6800MP
- Page 1 Connecting the Units Note: • This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recre- ational vehicle, truck, or bus, check the battery voltage. • To avoid shorts in the electrical system, be sure to disconnect the ≠...
-
Page 2: Connecting The Units
Connecting the Units 7 When using a Subwoofer without using the optional amplifier Antenna jack Subwoofer output 15 cm (5-7/8 in.) 16 cm (6-1/4 in.) Front output This product Subwoofer output IP-BUS input (Blue) Fuse (10 A) Jack for the Wired Remote Control Please see the Instruction Manual for the Multi-CD player Wired Remote Control (sold separately). -
Page 3: Din Rear-Mount
Installation DIN Rear-mount Fixing the front panel Installation using the screw holes on the side of the unit 1. Remove the frame. (Fig. 8) Frame To remove the frame, extend top and bottom of the frame outwards in order to unlock it. (When reattaching the frame, point the side with a groove downwards and attach it.) •... -
Page 4: Raccordements Des Appareils
Raccordements des appareils Raccordements des appareils Remarque: 7 Lorsque l’on ne connecte pas de câble de liaison au haut-parleur d’extrêmes graves • Cet appareil est destiné aux véhicules avec une • Quand la source de ce produit est positionnée sur batterie de 12 V, avec pôle négatif à... -
Page 5: Montage Din Avant/Arrière
Raccordements des appareils 7 Lors de l’utilisation d’un haut-parleur d’extrêmes graves sans l’amplificateur optionnel Sortie pour haut-parleur Jack d’antenne d’extrêmes graves 15 cm 16 cm Sortie avant Ce produit Sortie pour haut-parleur Entrée IP-BUS d’extrêmes graves Fusible (Bleu) (10 A) Prise pour la têléommande câblée Lecteur de CD à... -
Page 6: Montage Din Arrière
Installation Montage DIN arrière Fixation de la face avant Si vous n’utilisez pas la fonction de dépose et pose de la face avant, utilisez la vis de fixation fournis et fixez la face avant à l’appareil. Installation en utilisant les trous de vis sur les côtés de l’appareil 1.