Sony ZRD-1 Operating Instructions Manual
Display unit; display controller
Hide thumbs
Also See for ZRD-1:
- Service manual (102 pages) ,
- Operating instructions manual (23 pages) ,
- Installation manual (171 pages)
Table of Contents
Related Manuals for Sony ZRD-1
Summary of Contents for Sony ZRD-1
- Page 1 4-692-870-12 (1) Display Unit Display Controller Operating Instructions Before operating the unit, please read this manual and the supplied Before Using this Unit document thoroughly and retain it for future reference. ZRD-1 ZRCT-100 © 2016 Sony Corporation...
-
Page 2: Table Of Contents
• Sony assumes no responsibility for damages, loss of income, or any claims from a third party arising out of use of the system. -
Page 3: Please Read This First
Operating the product while condensation is present may damage the product. Security SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND RESULTING FROM A FAILURE TO IMPLEMENT PROPER SECURITY MEASURES ON TRANSMISSION DEVICES, UNAVOIDABLE DATA... -
Page 4: Overview
Overview You can connect the display units based on the installation location and intended use, convert the video content signals that are input to the display controller based on the array size, and output the signals onto the display units. 4K2K video can be controlled via a single display controller. -
Page 5: Parts Identification
Parts Identification ZRD-1 Display Unit Left / rear c - IN (AC power input) connector Caution Use a power cord (not supplied) to connect this connector to the - OUT (AC power output) Do not connect the OUT and IN connectors to a hub. The... -
Page 6: Zrct-100 Display Controller
f - OUT (AC power output) connector This connector is not used for the last display unit in Use a power cord (not supplied) to connect this the daisy-chain connection. connector to the - IN (AC power input) connector on the succeeding display unit in the daisy-chain connection. - Page 7 Rear Caution (earth) terminal Connect this to the earth conductor of the system. Do not connect the UNIT OUTPUT, LINK IN, and LINK OUT connectors to a hub. The input/output signals for Caution these connectors are unique to the product and are not Ethernet signals.
-
Page 8: Turning The Power On/Off
You can enter standby mode by pressing the power Turning the Power On/Off switch again while the indicator is still blinking red. Turn on the video source equipment. Turning the Power On Turning the power on via Display Control You can turn on the system’s power using one of three Software methods. -
Page 9: Turning The Power Off
Turning the Power Off Selecting the Video Input You can turn off the system’s power using one of two methods. Select the video signals that will be input. • Turning the power off via the display controller The settings configured on the primary controller will be •... -
Page 10: Changing The Display Starting Positions Of Pictures
DVI connector 1 DVI connector 3 Changing the Display Starting Positions of Pictures You can change the display positions for each picture. For example, you can move a low-resolution picture from the top left of the screen to the center. Click [Detailed Input Settings] in the [Input Settings] screen. -
Page 11: Adjusting The Picture Quality
[Gamma]: Select the gamma correction value. Adjusting the Picture Default value: 2.2 Quality Caution This product is not a medical device. The device Adjust the contrast, brightness, and other picture quality cannot be used for medical examinations, even settings. when [DICOM SIM] is selected. The settings configured on the primary controller will be applied to all the other display controllers, including the [Color Space]: Select the color space. -
Page 12: Displaying 3D Video
Note Displaying 3D Video Inversion and phase adjustments can be configured for both mixed L/R and separated L/R. The settings are Note reflected in the picture immediately after they are configured. In this document, the signals for the left and right eyes are referred to as the L and R signals respectively. -
Page 13: Troubleshooting
Be sure to conduct a check before requesting assistance. If clicking it and selecting [Controller Info.]. the problem persists, contact your local Sony representative. [Array Information] Displays the status of each display unit. - Page 14 Entering the forced standby mode If the controller PC hangs, for example, you can force display controllers and display units into standby mode. Press and hold the power switch on the display controller for at least 5 seconds. The forced standby mode is entered, and the POWER indicator lights red.
-
Page 15: Error Codes
UP Board (CELL_1 to CELL_12) Connection/ Connection_Error / RS485 Check that all cables are properly connected. If the problem communication Communication / Video Input Signal / persists, contact your local Sony representative. Connection_Error / RS485 Communication / Video Input Signal Warnings Warning Category... -
Page 16: Display Controllers
Check the installation, wiring, and Display Control Software mismatch warning settings, and if a problem does not exist, turn the power off and turn it on again. If the problem persists, contact your local Sony DIF signal connection warning / representative. -
Page 17: Cleaning And Storage
Cleaning and Storage Signal Formats The system supports the following video signals. Display Units DisplayPort (single input) Caution Resolution Input frame rate Input bit Input color length sampling Do not wet the surface of the display units. 3840 × 2160 60p/50p/30p/25p/ 8-/10-bit RGB 4:4:4... - Page 18 Sony Corporation...