Table of Contents
- 1 Clock Window
- 2 Two Year Limited Warranty
- 3 Reset Key
- 4 Battery Door
- 5 Battery Replacement
- 6 Reception of Radio Controlled Time Signal
- 7 Daylight Savings Time (Dst)
- 8 Signal Strength Indicator
- 9 Time Zone Setting
- 10 Time and Calendar Setting
- 11 Viewing the Channel
- 12 Alarm Time Setting
See also:
Instruction Manual
Table of Contents
Related Manuals for Sharp SPC900
Summary of Contents for Sharp SPC900
- Page 1 C8318A (WWVB) PD09025M Size: 105 x 130 (mm) RADIO CONTROLLED WIRELESS THERMO CLOCK USER’S INSTRUCTIONS P178318GB010...
- Page 2 Thank you for your purchase of this delicate Wireless Thermo reasonable protection against harmful interference in a clock. The utmost care has gone into the design and residential installation. This equipment generates, uses and manufacture of your clock. Please read these instructions can radiate ratio frequency energy and, if not installed and carefully and keep the manual well for future reference.
-
Page 3: Clock Window
Printed in China SPC900 SHARP, registered in the U.S. Patent and Trademark Office This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and... -
Page 4: Two Year Limited Warranty
4. TIME key: - In normal time mode, press it to enter alarm1 and TWO YEAR LIMITED WARRANTY alarm2 time mode. - Press and hold it for 2 seconds to enter the normal M.Z. Berger & Company warrants the original consumer time setting mode. -
Page 5: Reset Key
8. ALM ON/OFF key: RF transmission frequency: 915 MHz - In normal time mode, press it to turn on/off alarm1 & alarm2. No. of remote unit: up to 2 units - In alarm time mode, press it to turn on/off alarm and temperature pre-alarm. - Page 6 13. WALL-MOUNTING HOLDER: - Use it to support the main unit in the wall mounting. 14. TABLE STAND: - Use it to stand the clock on the desktop. 15. BATTERY DOOR TRANSMITTER SPECIFICATIONS MAIN UNIT Recommended operating range: 0 °C to 45 °C 32 °F to 113 °F Resolution: 0.1°C (above -9.9°C)
-
Page 7: Battery Door
5. BATTERY DOOR For the transmitter, fix the separate wall-mounting stand outside in the area protected from direct rain by the screw. 6. WALL-MOUNTING HOLDER: Once the stand is mounted, place the transmitter into the - Use it to support the transmitter on the wall. stand on the wall. -
Page 8: Battery Replacement
BATTERY REPLACEMENT OPERATING THE TRANSMITTER Remove the transmitter from the stand and open the If the low battery indicator “ ” appears beside the outdoor battery door. temperature of main unit, it indicates that you should replace Insert 2 AA size batteries into the battery compartment batteries of transmitter at once. -
Page 9: Daylight Savings Time (Dst)
DAYLIGHT SAVINGS TIME (DST) HOW TO READ TEMPERATURE RECORDS Change the temperature unit to °C for Celsius or °F for The clock has been programmed to automatically switch Fahrenheit by pressing “°C/°F” key. when the daylight savings time is in effect. Your clock will show “DST”... -
Page 10: Time Zone Setting
The temperature pre-alarm can sound 30 minutes earlier than the alarm only when the outdoor temperature is below 26.0°F (-3.0°C). If no key is pressed during the alarm period, the clock will enter the snooze mode automatically. Besides, TIME ZONE SETTING you can also press “SNOOZE”... -
Page 11: Alarm Time Setting
Repeat the above operations (point 3, 4) to set the Press “UP” or “DOWN” key to change its value. below items in this order: Date > Hour > Minute > Press “ALM ON/OFF” key once until the alarm Minute Second > Day language > +/-23 hours time difference. digit flashes.