Hide thumbs Also See for 26HW9100D, 30HW9100D:

Quick Links

L05 User's Manual
091105.1833
26HW9100D/30HW9100D User's Manual
1
Table of Contents
loading

Summary of Contents for Philips 26HW9100D, 30HW9100D

  • Page 1 L05 User’s Manual 091105.1833 26HW9100D/30HW9100D User’s Manual...
  • Page 2: Safety Information

    L05 User’s Manual SAFETY INFORMATION Disconnect mains plug when: Ø the red light below the TV screen is flashing continuously. Ø a bright white line is displayed across the screen. Ø cleaning the TV screen. Never use abrasive cleaning agents. Use a slightly damp chamois leather or soft cloth.
  • Page 3: Before Calling Service

    L05 User’s Manual Before Calling Service A list of common symptoms is presented as follows. Before you call for service, perform these simple checks. Some of these symptoms can be readily corrected. Note: Please become familiar with the commercial features as described in TV Installation / Setup, because the effects of several of these features, if they are not thoroughly understood, might appear as faulty operation.
  • Page 4: Basic Television Connection

    L05 User’s Manual 091105.1833 Basic Television Connection Antenna Connection • Connect the antenna or RF cable signal to the 75-ohm RF ‘F’ connector socket located on the TV’s rear jack panel. Mains Connection • Verify that the mains voltage and frequency are correct.
  • Page 5: Rear Jack Panel Connections

    L05 User’s Manual Use And Care of Remote Control Rear Jack Panel Connections To load the supplied batteries into the remote control: Remo ve the battery compartment lid from the back of the remote control. Insert the correct type of batteries into the compartment.
  • Page 6: Remote Controls

    L05 User’s Manual REMOTE CONTROLS The following remote controls are applicable to the L05 HW-series television products. These can be used for setup and configuration purposes. RC2888/01 Guest Remote For the purpose of explanation, a guest remote, for the L04 series, similar to the illustration, is used.
  • Page 7: Guest Remote Control Keys

    L05 User’s Manual Guest Remote Control Keys Source Select To toggle between available video sources DVD PAUSE To Pause DVD playback Close Caption To activate Close Caption functionality DVD STOP To Stop DVD playback (if applicable) Menu To call up or exit the menus.
  • Page 8 L05 User’s Manual Consumer vs. Commercial Mode The television is shipped in Commercial mode; however, at times it may be necessary to operate the set in Consumer mode. To switch between Commercial Mode and Consumer Mode the following sequence should be followed: With the RC2573GR Master setup remote enter 024995 and press the Use the Right cursor button to switch the Mode of the set between Consumer and Commercial.
  • Page 9 L05 User’s Manual 1. Press the RECALL key to clear the menu. 2. Press 0 2 4 9 9 5. 3. Press M key and the TV Mode menu appears. 4. Press + or - to select Commercial mode. 5. Highlight STORE and press the 4 key to store the change. TV will then go to standby mode.
  • Page 10: Tv Setup Main Menu

    L05 User’s Manual TV Setup Main Menu LANGUAGE CHANNEL INSTALL CABLE TUNING FACTORY CH RESET USE CHANNEL TABLE DIGITAL OSD ENTER DIGITAL MENU BRIGHTNESS COLOR CONTRAST SHARPNESS TINT ROTATION DEFAULT FORMAT NOISE REDUCTION SOUND MODE BALANCE TREBLE BASS INCREDIBLE STEREO ULTRA BASS VOLUME BAR MIN VOLUME...
  • Page 11 L05 User’s Manual TV Setup Menu and Sub-Menus LANGUAGE When you first enter the TV SETUP menu, LANGUAGE is highlighted. You can scroll to the LANGUAGE item. Select the desired language with cursor up / cursor down. CHANNEL INSTALL The CANNEL INSTALL menu allows the user to configure the channels that can be accessed.
  • Page 12 L05 User’s Manual o Specify whether the current channel or input is to be SAVED to or DELETED from the channel ring (i.e., list of channels available for selection by means of a standard guest remote control). LABEL: o Input a maximum of 8 characters for the channel’s label. Cursor to the Right to start the first character.
  • Page 13 L05 User’s Manual CHANNEL INPUT MAJOR CHANNEL MINOR CHANNEL CHANNEL RING LABEL VIDEO BLANK AUDIO MUTE CHANNEL: o Select the channel or input you wish to configure. INPUT: o When DIGITAL is selected two additional entries are added to the menu to allow for mapping the digital channels.
  • Page 14 L05 User’s Manual USE CHANNEL TABLE When NO is selected the MAJOR channel in the Digital channel setup in the CHANNEL INSTALLATION menu refers to an RF channel (frequency). When YES is selected the Major channel refers to the Major channel listed in the Digital Channel Map. DIGITAL OSD Specify whether the consumer digital version of the OSD is displayed when MENU is pressed from a digital channel.
  • Page 15 L05 User’s Manual Note: The digital channels must be programmed using the Digital Menu to allow for the fastest possible channel change times. To exit the digital menu, press the BRIGHTNESS Adjust the respective picture setting, using left and right cursor. COLOR Adjust the respective picture setting, using left and right cursor.
  • Page 16: Noise Reduction

    L05 User’s Manual Using the different formats Select the preferred format from the DEFAULT FORMAT menu item in the setup screen, or (if applicable) use the Format button on the Remote Control to select the different modes: 4:3, Zoom 14:9, Zoom 16:9, Subtitle zoom, Super Zoom, and Widescreen.
  • Page 17 L05 User’s Manual SOUND MODE Select either STEREO or MONO (monaural) sound modes. Note: STEREO has no effect if the current audio signal is monaural. When SOUND MODE is changed, an on-screen display will appear, indicating the actual audio status (MONO or STEREO) Disable or enable the Automatic Volume Leveling feature, which minimizes variations in audio playback level.
  • Page 18 L05 User’s Manual MAX VOLUME Specify the highest volume setting possible by means of either the remote control, or the front panel (if it is not locked out). This setting cannot be less than MIN VOLUME (see MIN VOLUME) Note: The MAX VOLUME setting is effective whether the volume command is issued from the front panel (if it is not locked out), a standard guest- mode remote control, or an RC2573GR setup remote in setup mode.
  • Page 19 L05 User’s Manual Energy Saving Programmability. This feature enables the TV to automatically power- down after a specified period of time, if during any such period it receives no commands from the front panel or remote control. This is an energy-saving feature which assumes that the TV, after the specified period of inactivity, is no longer being viewed.
  • Page 20: Channel Guide

    L05 User’s Manual DISPLAY Cursor right or left to select NO to disable the WELCOME MESSAGE or YES to enable it. Note: If welcome message is enabled, and both LINE 1 and LINE 2 are blank (or consist entirely of space characters), no message will appear. LINE 1/LINE 2 Select message LINE 1 or LINE 2.
  • Page 21: Digit Entry

    L05 User’s Manual Note 2: Only RF (tuner) channels will be listed in the channel guide. Video inputs (AUX, S-VIDEO, CVI, FRONT A/V) will not appear in the channel guide. REMINDER When REMINDER = YES, the reminder feature provides a constant on-screen indication of the current channel or input, (e.g., TV 2, CVI, etc.), that channel’s or input’s label (if a label has been assigned in CHANNEL INSTALL), and the current MUTE status (i.e., if sound MUTE is active).
  • Page 22 L05 User’s Manual CC-2: CC-2-mode closed captioning will be displayed if it is present on the incoming signal. CC ON MUTE: If the television is in audio mute mode, CC-1-mode closed captioning will be displayed if it is present on the incoming signal. Note: When the television is powered down and back on again, the closed captioning setting will default to OFF, unless SAVE CC (see SAVE CC) is set to YES.
  • Page 23: V-Chip Set Up

    L05 User’s Manual DVI output, a DVI to HDMI converter is required for the video input to the television, and the analog audio can be configured on any of the listed audio inputs. V-CHIP MENU ITEM This feature provides the option to specify whether the V-CHIP SETUP menu item is present in the FEATURES MENU which appears when the remote control SLEEP or CC command is issued, or when a guest- mode remote control RECALL command is issued.
  • Page 24 L05 User’s Manual 091105.1833 television receives a remote control or front-panel command, whereas the ESP timer is reset whenever the television receives a command from a remote control or from the front panel. Note 2: If the SLEEPTIMER is in progress, the current SLEEPTIMER countdown timer value appears in the ITV / commercial SETUP MENU, as well as in the FEATURES MENU.
  • Page 25 L05 User’s Manual 091105.1833 26HW9100D Dimensions...
  • Page 26 L05 User’s Manual 091105.1833 30HW9100D Dimensions...

Table of Contents