Related Manuals for GE druck dpi 104
Summary of Contents for GE druck dpi 104
- Page 1 99 Washington Street GE Industrial Melrose, MA 02176 Fax 781-665-0780 Sensing TestEquipmentDepot.com Druck DPI 104 Digital pressure indicator User manual - K394...
- Page 2 A1.1 A1.2 A1.3 Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 FAX 781.665.0780 - TestEquipmentDepot.com...
-
Page 3: Table Of Contents
Table of Contents Introduction The Druck DPI 104 is a digital pressure indicator that Introduction ................. 1 measures the pressure of liquid, gas or vapour and shows Safety ..................1 the pressure value on a liquid crystal display (LCD). It also Marks and symbols on the DPI 104 ........ -
Page 4: To Start
To Start Item Description To start - Location of items Mode indication. Item Description Voltage output (Vout) mode - On. 8-pin connector for external power supplies, RS232 connection. The data transmit/receive function RS232/UPM connections and signal input/output. is active. • Power on button Switch mode - On. -
Page 5: Menu Operation
To start - Menu operation Menu Description Steps Result/Subsequent steps = Power supply: OFF only Power goes off unitS = Set units: (A2: item 14). Pressure value changes to the applicable units: psi, mbar, bar ... t OFF = Set tare: Set to On or OFF. tA 00.000 : Set a tare value (Refer to Table 4) = Monitor maximum/minimum: Monitor function is set on or off... -
Page 6: Installation
Installation This section shows how to install and connect the DPI 104. a) 1/4 NPT: Before you start: < Pressure 1000 bar (15000 psi) • Read and understand the “Safety” section. • Do not use a damaged DPI 104. Installation - Battery A1.2 A1.3 b) G1/4:... -
Page 7: Operation
Operation To make sure that there is an indication of the correct pressure while tare is On, the analogue dial and % This section shows how to use the DPI 104. Before you indication show values calculated from the calibrated start: range without the tare adjustment. -
Page 8: Menu: Monitor A Pressure Switch
Operation - Menu: Monitor a pressure switch Low/high alarm - Set up and use Use this function to measure the performance of a Menu: Set this function to On (Refer to “To start - Menu pressure switch (mechanical operation and hysteresis). operation”). -
Page 9: Menu: Set Vout Scale Factor
Operation - Menu: Set lock code Pin 1 (+), 2 (GND) Use the lock function to prevent accidental changes to the 12- 24V dc configuration. There are two options: • Lock code < 500: This locks the menu and the tare Vout: 0 to 5V function. -
Page 10: Menu: Set Fso Low/High Registers
Operation - Menu: Set FSO low/high registers PC: 9-way, D-type Use the FSO low/high registers to set a different range for connector these functions: analogue display, % indication, low/high alarm. 12- 24V dc Initially, these register values are set to the factory calibration values. -
Page 11: Maintenance
To stop and make changes to a value, press this button. Calibration To return to the normal display, wait eight seconds. Note: GE can provide a calibration service that is traceable to international standards. Calibration - C0 (Zero offset) We recommend that you return the DPI 104 to the... - Page 12 Calibration - C2 (two-point pressure calibration) Calibration - V2 (two-point voltage calibration) Point 1 (P1) - The DPI 104 shows these displays: Point 1 (P1) - The DPI 104 shows these displays: 1. The calibration point to be used for C2 - Point 1. This 1.
-
Page 13: Specification Data
Specification data Specification - General Operating temperature -10 to 50°C (14 to 122°F) Storage temperature -20 to 70°C (-4 to 158°F) Ingress Protection IP65 (Dust-tight, jets of water) Materials Case: Acrylonitrile Butadiene Styrene (ABS) Refer also to Media notes. Humidity 0 to 95% without condensation (Def Stan 66-31, 8.6 cat III) Shock/Vibration...