1. Manuals
  2. Brands
  3. Emerson Manuals
  4. Measuring Instruments
  5. Rosemount 3051
  6. Quick start manual

Emerson Rosemount 3051 Quick Start Manual

Flowmeters / pressure transmitters
Hide thumbs Also See for Rosemount 3051:
Table of Contents

Quick Links

See also: Reference Manual , Manual
Quick Start Guide
00825-0200-4774, Rev BC
August 2016
™
Rosemount
3051 Pressure Transmitter
and Rosemount 3051CF Series Flowmeters
™
with F
Fieldbus Protocol
OUNDATION
Note
Before installing the transmitter, confirm the correct device driver is loaded on the host systems.
See
"System readiness" on page
3.
Table of Contents
loading

Related Manuals for Emerson Rosemount 3051

Summary of Contents for Emerson Rosemount 3051

  • Page 1 Quick Start Guide 00825-0200-4774, Rev BC August 2016 ™ Rosemount 3051 Pressure Transmitter and Rosemount 3051CF Series Flowmeters ™ with F Fieldbus Protocol OUNDATION Note Before installing the transmitter, confirm the correct device driver is loaded on the host systems. “System readiness”...

  • Page 2: Table Of Contents

    August 2016 Quick Start Guide NOTICE This guide provides basic guidelines for Rosemount 3051 Transmitters. It does not provide instructions for configuration, diagnostics, maintenance, service, troubleshooting, Explosion-proof, Flameproof, or intrinsically safe (I.S.) installations. Refer to the Rosemount 3051 F Fieldbus...

  • Page 3: System Readiness

    Download the correct device driver at your host vendor download site,  EmersonProcess.com or fieldbus.org. Rosemount 3051 device revisions and drivers Table 1 provides the information necessary to ensure you have the correct device driver and documentation for your device.

  • Page 4: Transmitter Installation

    August 2016 Quick Start Guide 2.0 Transmitter installation 2.1 Mount the transmitter Liquid applications Coplanar In-line 1. Place taps to the side of the line. 2. Mount beside or below the taps. Flow 3. Mount the transmitter so that the drain/vent valves are oriented upward.
  • Page 5 Quick Start Guide August 2016 Figure 2. Panel and Pipe Mounting Panel mount Pipe mount Coplanar flange Traditional flange Rosemount 3051T panel bolts are customer supplied.
  • Page 6 Use only bolts supplied ™ with the transmitter or sold by Emerson Process Management as spare parts. Figure 3 on page 6 illustrates common transmitter assemblies with the bolt length required for proper transmitter assembly.
  • Page 7 Quick Start Guide August 2016 Table 2. Torque Values for the Flange and Flange Adapter Bolts Bolt material Head markings Initial torque Final torque 300 in-lb 650 in-lb Carbon Steel (CS) Stainless Steel (SST) 150 in-lb 300 in-lb O-rings with flange adapters Failure to install proper flange adapter O-rings may cause process leaks, which can result in death or serious injury.
  • Page 8 August 2016 Quick Start Guide In-line gage transmitter orientation The low side pressure port (atmospheric reference) on the in-line gage transmitter is located in the neck of the transmitter, behind the housing. The vent path is 360° around the transmitter between the housing and sensor. (See Figure Keep the vent path free of any obstruction, including but not limited to paint, dust, and lubrication by mounting the transmitter so fluids can drain away.

  • Page 9: Tagging

    Quick Start Guide August 2016 2.2 Tagging Commissioning (paper) tag To identify which device is at a particular location use the removable tag provided with the transmitter. Ensure the physical device tag (PD Tag field) is properly entered in both places on the removable commissioning tag and tear off the bottom portion for each transmitter.

  • Page 10: Consider Housing Rotation

    August 2016 Quick Start Guide 2.3 Consider housing rotation To improve field access to wiring or to better view the optional LCD display: 1. Loosen the housing rotation set screw using a -in. hex wrench. 2. Rotate the housing clockwise to the desired location. 3.

  • Page 11: Wire, Ground, And Power Up

    Quick Start Guide August 2016 Figure 7. Simulate and Security Switches A. Simulate disabled position D. Security locked position B. Simulate switch E. Security switch C. Simulate enabled position (default) F. Security unlocked position (default) 2.5 Wire, ground, and power up Use of copper wire of sufficient size to ensure the voltage across the transmitter power terminals does not drop below 9 Vdc.
  • Page 12 Quick Start Guide Note The Rosemount 3051 power terminals are polarity insensitive, which means the electrical polarity of the power leads does not matter when connecting to the power terminals. If polarity sensitive devices are connected to the segment, terminal polarity should be followed.

  • Page 13: Configure

    DD methods for configuration and to display data consistently across platforms. There is no requirement that a host or configuration tool support these features. Use the following block examples to do basic configuration to the transmitter. For more advanced configurations, see the Rosemount 3051 F Fieldbus OUNDATION Reference Manual.
  • Page 14 August 2016 Quick Start Guide Figure 9. Configuration Flowchart Start 6. Set Low Cutoff: 1. Verify Device Tag: Device Configuration LOW_CUT PD_TAG Here 7. Set Damping: 2. Check Switches and PRIMARY_VALUE_ Software Write Lock DAMPING 8. Set up LCD Display 3.
  • Page 15 Fieldbus Diagnostics Suite Option Code D01 is enabled, these OUNDATION additional channels are available. Channel 12 is the SPM mean.  Channel 13 is the SPM standard deviation.  To configure SPM, refer to the Rosemount 3051 F Fieldbus Reference OUNDATION Manual.
  • Page 16 August 2016 Quick Start Guide Note Step 3 through Step 6 are all performed in a single step by step method under guided setup, or on a single screen using manual setup. Note If the L_TYPE selected in Step 3 is “Direct”, Step Step 5...
  • Page 17 Quick Start Guide August 2016 Note Guided setup will automatically go through each step in the proper order. Enter the desired damping value in seconds. The permitted range of  values is 0.4 to 60 seconds. b. To use manual setup: Navigate to Configure>Manual Setup>Process Variable.
  • Page 18 August 2016 Quick Start Guide Enable software write lock 1. Navigate from the Overview screen. a. Select Device Information. b. Select the Security and Simulation tab. 2. Perform Write Lock Setup to enable software write lock. AI block configuration parameters Use the pressure, DP Flow, and DP Level examples for guides.

  • Page 19: Zero Trim The Transmitter

    Quick Start Guide August 2016 DP Level example Parameters Enter data Channel L_Type Indirect XD_Scale 0–300 inH O @ 68 °F Note Select only the units that are supported by the device. Out_Scale 0–25 ft Display pressure on the LCD display Select the Pressure check box on the Display Configuration screen.

  • Page 20: Product Certifications

    Care must be taken into account during installation and use to prevent impact and friction. 2. The Rosemount 3051 Transmitter with the transient terminal block (Option code T1) will not pass the 500 Vrms dielectric strength test and this must be taken into account during installation.
  • Page 21 Quick Start Guide August 2016 C6 Canada Explosionproof, Dust-Ignitionproof, Intrinsic Safety and Nonincendive Certificate: 1053834 Standards: ANSI/ISA 12.27.01-2003, CSA Std. C22.2 No. 30-M1986, CSA Std. C22.2 No.142-M1987, CSA Std. C22.2. No.157-92, CSA Std. C22.2 No. 213-M1987 Markings: Explosionproof for Class I, Division 1, Groups B, C and D; Suitable for Class I, Zone 1, Group IIB+H2, T5;...
  • Page 22 August 2016 Quick Start Guide I1 ATEX Intrinsic Safety and Dust Certificate: BAS97ATEX1089X; Baseefa11ATEX0275X Standards: EN60079-0:2012, EN60079-11:2012, EN60079-31:2009 II 1 G Ex ia IIC T5/T4 Ga, T5(–60 °C ≤ T ≤ +40 °C), Markings: HART: T4(–60 °C ≤ T ≤ +70 °C) II 1 G Ex ia IIC Ga T4(–60 °C ≤...
  • Page 23 Quick Start Guide August 2016 N1 ATEX Type n and Dust Certificate: BAS00ATEX3105X; Baseefa11ATEX0275X Standards: EN60079-0:2012, EN60079-15:2010, EN60079-31:2009 II 3 G Ex nA IIC T5 Gc (–40 °C ≤ T ≤ +70 °C); Markings: 105 °C Da (–20 °C ≤ T ≤...
  • Page 24 August 2016 Quick Start Guide Special Conditions for Safe Use (X): 1. If the apparatus is fitted with optional 90 V transient suppressor, it is not capable of withstanding the 500 V insulation test required by IEC60079-11. This must be taken into account when installing the apparatus.
  • Page 25 Quick Start Guide August 2016 2. In case of repair, contact the manufacturer for information on the dimensions of the flameproof joints. 3. The capacitance of the wrap around label, being 1.6 nF, exceeds the limit in Table 9 of ABNT NBR IEC 60079-0.
  • Page 26 August 2016 Quick Start Guide 3.7 China E3 China Flameproof Certificate: GYJ14.1041X; GYJ15.1368X [Flowmeters] Standards: GB12476-2000; GB3836.1-2010, GB3836.2-2010, GB3836.20-2010 Markings: Ex d IIC T6/T5 Ga/Gb, T6(–50 °C ≤ T ≤ +65 °C), T5(–50 °C ≤ T ≤ +80 °C) Special Conditions for Safe Use (X): 1.
  • Page 27 Quick Start Guide August 2016 3. Intrinsically Safe parameters: Parameter HART Fieldbus/PROFIBUS FISCO Voltage U 30 V 17.5 V Current I 200 mA 300 mA 380 mA Power P 0.9 W 1.3 W 5.32 W 0.012 μF 0 μF Capacitance C <5 nF <10 μH Inductance L...
  • Page 28 August 2016 Quick Start Guide 3.9 Technical Regulations Customs Union (EAC) EM EAC Flameproof Certificate: RU C-US.GB05.B.01197 Markings: Ga/Gb Ex d IIC T5/T6 X, T5(–60 °C ≤ T ≤ +80 °C), T6(–60 °C ≤ T ≤ +65 °C) Special Condition for Safe Use (X): 1.
  • Page 29 Quick Start Guide August 2016 Table 12. Thread Adapter Thread Sizes Female thread Identification mark 1.5–6H –14 NPT –14 NPT Special Conditions for Safe Use (X): 1. When the thread adapter is used with an enclosure in type of protection increased safety “e”...
  • Page 30 August 2016 Quick Start Guide Figure 11. Rosemount 3051 EC Declaration of Conformity...
  • Page 31 Quick Start Guide August 2016...
  • Page 32 August 2016 Quick Start Guide...
  • Page 33 Quick Start Guide August 2016...
  • Page 34 August 2016 Quick Start Guide Rosemount 3051 China RoHS List of Rosemount 3051 Parts with China RoHS Concentration above MCVs / Hazardous Substances Hexavalent Polybrominated Polybrominated Part Name Lead Mercury Cadmium Chromium biphenyls diphenyl ethers (Pb) (Hg) (Cd) (Cr +6)
  • Page 35 Quick Start Guide August 2016...
  • Page 36 +65 6777 0947 Standard Terms and Conditions of Sale can be found at www.Emerson.com/en-us/pages/Terms-of-Use.aspx [email protected] The Emerson logo is a trademark and service mark of Emerson Electric Co. Middle East and Africa Regional Office AMS, DeltaV, Rosemount, and Rosemount logotype are Emerson Process Management trademarks of Emerson Process Management.

This manual is also suitable for:

Rosemount 3051 cf series

Table of Contents