Craftsman 81338 Operator's Manual

Drawer cabinet
Table of Contents
Available languages

Available languages

Quick Links

OPERATOR’S MANUAL
R
MOdEL # 81338 36” (7)-dRAwER CAbiNET
MOdEL # 2915 46” (13)-dRAwER CAbiNET
service parts
call 800.366.7278 for service parts. Refer to Service
Parts drawing for full listing of Service Parts.
locatiNG moDel # iNformatioN
Model numbers and other information required for service parts is
located on a label on the interior right side of the top most drawer.
capacities
• Empty weight of 36” cabinet is 308 lbs.
• Empty weight of 46” cabinet is 472 lbs.
• The maximum product weight, including contents, for the 36”
model should be no more than 1800 pounds.
• The maximum product weight, including contents, for the 46”
model should be no more than 3000 pounds.
• The maximum weight for each (2) inch deep drawer is (120)
pounds.
• The maximum weight for each (3) inch deep drawer is (200)
pounds.
• The maximum weight for each (4) - (6) inch deep drawer is
(320) pounds.
• The maximum weight for each drawer (9) inches deep or more
is (400) pounds.
maiNteNaNce
• For casters, use high quality bearing grease, (yearly).
• Lubricate the slides with grease or equivalent,(twice yearly.)
• Lubricate lock and locking system components with graphite,
(yearly).
distributed by Sears brands Management Corporation, Hoffman Estates, iL 60179
ball bearing slides
Friction slides
• Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mild detergent and water.
• Auto wax will preserve the unit’s luster finish. Apply the wax as to
a car. The wax will also help protect the unit against scratches.
• Grease and oil can be removed with most standard cleaning
fluids. For safety, use a nonflammable cleaning fluid.
• if drawer liners are supplied, it is recommended they are used
to protect the finish inside the drawers and to make the drawers
easier to clean. The drawer liners may be cleaned with soap and
water.
safety
DaNGer
is used to indicate a hazardous situation which,
if not avoided, will result in serious injury or death.
WarNiNG
indicates a hazardous situation which, if not
avoided, could result in serious injury or death.
cautioN is used to indicate a hazardous situation which, if not
avoided, may result in minor injury, moderate injury, or property
damage.
cautioN: Read and follow all Safety Rules and Operating
instructions before first use of this product.
DaNGer
• Do Not stand on this product. You may fall or cause product
to tip.
• Do Not open more than one drawer. The product may be-
come unstable and tip.
• Do Not step in the drawers. You may fall or cause product to
tip.
• Do Not mount this product on a truck bed or any other moving
object.
• Do Not move the product prior to closing and locking all the
drawers. The drawers could come open and make the product
unstable and tip.
WarNiNG
• Wear safety Glasses when removing or repositioning
the slides.
• Do Not pull this product when moving it. Push the product to
prevent personal injury.
• use the braKes when not moving this product. This will
prevent the product from rolling.
• Do Not alter this product in any manner. For example, do not
weld external lockbars or attach electrical equipment.
• Keep the product on level surfaces. The product may become
unstable and tip if stored or moved on an uneven surface.
• be careful when closing the cover. Remove hands before
the cover closes completely.
cautioN
• This product is not designed to be directly lifted with a fork lift,
or to be towed with any mechanical devices.
• The maximum weight for each drawer should never be ex-
ceeded.
• Only transport this product empty. Properly secure when
transporting.
• Do Not exceed maximum product weight, including contents.
See Operations Sections: Capacities for more information.
use aDequate maNpoWer WheN liftiNG or mov-
iNG the chest or cabiNet.
Rev A - F1848
Table of Contents
loading

Summary of Contents for Craftsman 81338

  • Page 1 OPERATOR’S MANUAL ball bearing slides Friction slides MOdEL # 81338 36” (7)-dRAwER CAbiNET • Periodically the drawer fronts, drawer trim, and other surfaces MOdEL # 2915 46” (13)-dRAwER CAbiNET should be cleaned with a mild detergent and water. • Auto wax will preserve the unit’s luster finish. Apply the wax as to a car.
  • Page 2: Carton Contents

    harDWare assembly siDe haNDle iNstallatioN Hardware and other included contents can be found in the bottom drawer (unless otherwise noted). items Needed: 1/4 - 20 x 1-1/2" Hex Screw (Qty: 4) tools requireD: Handle (Qty: 1) 3/8” wrench 1/2” wrench 3/8-in wrench 5/16"...
  • Page 3: Operation

    DiviDer iNstallatioN items Needed: 10-24 x 5/16 Hex Screw (Qty: 8) dividers (Qty: 6) 5/16" wrench process: • decide which position and in which drawers they would best serve your needs. • The dividers are cut to fit right to left in the drawers. if you prefer to run them front to back, they may be trimmed in length to do so.
  • Page 4 friction style - Fully extend the drawer. insert screwdriver operatioN into the slot in the side and push in on the stop until it removiNG aND iNstalliNG DraWers clears the lance. Pull drawer just past lance before releasing stop. Repeat the process for the other slide. •...
  • Page 5: Troubleshooting

    reiNstall DraWers removiNG aND iNstalliNG sliDes slide removal - ball bearing slide - Pull slides and slide carrier out to fully • The drawers in these units can be rearranged to fit your extended position (see illustration.) Hold the slide on the specific needs.
  • Page 7: Piezas De Servicio

    MANUAL dE USUARiO Cojinetes de bolas Correderas de friccion MOdELO NO 81338 GAbiNETE dE 36iN (91,4 CM) • Lubrique la cerradura y la fijación de componentes de sistema con el CON (7) CAjONES grafito, (anualmente). MOdELO NO 2915 GAbiNETE dE 46iN (116,8 CM) •...
  • Page 8 ferreterÍa eNsamblaJe El hardware y otros contenido incluidos pueden ser encontrados iNstalaciÓN De la maNiJa lateral en el ajuar (a menos que se indique lo contrario). elementos necesarios: herramieNtas Necesarias: Tornillo Hexagonal de 1/4-20 X 1 1/2 (Cant.: 4) Llave inglesa de 3/8” Manija (Cant.: 1) Llave inglesa de 5/16”...
  • Page 9 iNstalaciÓN De los Divisores elementos necesarios: Tornillo hexagonal de 10-24 x 5/16 (Cant.: 24) divisores (Cant.: 6) Llave inglesa de 5/16” Proceso: • decida qué posición y en cuáles gavetas se adaptarán mejor a sus necesidades. • Los divisores están cortados para encajar de derecha a izqui- erda en las gavetas.
  • Page 10 estilo fricción - extienda completamente la gaveta. inserte el REMOCiÓN E iNSTALACiÓN dE GAVETAS destornillador en la ranura del costado y presione el tope hasta • Vacíe la gaveta. que libere el rejón. Hale la gaveta justo después del rejón antes •...
  • Page 11: Solución De Problemas

    iNstalaciÓN De Gavetas quitaNDo e iNstalaciÓN De Diapositivas remoción de la corredera - correderas de rodamientos esféricos - hale hacia • Las gavetas de estas unidades pueden disponerse de otro afuera las correderas y el soporte de las correderas hasta que modo para que se adapten a sus necesidades específicas.

This manual is also suitable for:

2915

Table of Contents