Hitachi CP-WU8460 User Manual
Hide thumbs Also See for CP-WU8460:
Projector
CP-X8170/CP-WX8265/CP-WU8460
User's Manual (concise)
Thank you for purchasing this projector.
Please read through this manual before using this product, in order to use safely
and utilize well the product.
WARNING
product. After reading them, store them in a safe place for future reference.
NOTE
means this projector and all the accessories came with the projector.
Contents
............................................ 2
Important safety instruction ..............................2
Regulatory notices .............................. 3
Contents of package........................... 4
Arrangement ....................................... 6
Connecting power supply ................... 8
Turning on the power .......................... 9
Adjusting the lens position ................ 10
Displaying the picture ....................... 11
Turning off the power ........................ 12
Replacing the lamp ........................... 13
Using the CD manual ....................... 17
............... 8
................................... 18
.. 15
1
Table of Contents
loading

Summary of Contents for Hitachi CP-WU8460

  • Page 1: Table Of Contents

    Projector CP-X8170/CP-WX8265/CP-WU8460 User's Manual (concise) Thank you for purchasing this projector. Please read through this manual before using this product, in order to use safely and utilize well the product. WARNING product. After reading them, store them in a safe place for future reference.
  • Page 2: Entries And Graphical Symbols Explanation

    First of all Entries and graphical symbols explanation The following entries and graphical symbols are used for the manuals and the product as follows, for safety purpose. Please know their meanings beforehand, and heed them. WARNING This entry warns of a risk of serious personal injury or even death. CAUTION This entry warns of a risk of personal injury or physical damage.
  • Page 3: Regulatory Notices

    Regulatory notices About Electro-Magnetic Interference This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. This product may cause interference if used in residential areas. Such use must be avoided unless the user takes special measures to reduce electromagnetic emissions to prevent interference to the reception of radio and television broadcasts.
  • Page 4: About Waste Electrical And Electronic Equipment

    Regulatory notices (continued) About Waste Electrical and Electronic Equipment The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE). The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorted municipal waste, but use the return and collection systems available.
  • Page 5: Preparing For The Remote Control

    Holding the hook part of the battery cover, remove it. Align and insert the two AA batteries (HITACHI MAXELL ENERGY, Part No.LR6 or R6P) according to their plus and minus terminals as indicated in the remote control.
  • Page 6: Arrangement

    Arrangement Refer to tables T-1 to T-3 at the back of this manual as well as the following to determine the screen size and projection distance. The values shown in the table are calculated for a full size screen. Ⓗ × Ⓥ : Screen size ⓐ...
  • Page 7: Connecting With Your Devices

    Connecting with your devices the required accessories, such as a cable in accord with the signal of the device. Consult your dealer when the required accessory did not come with the product or the accessory is damaged. After making sure that the projector and the devices are turned off, perform the gures F-1 to F-4 at the back of this manual.
  • Page 8: Connecting Power Supply

    Fastening the adapter cover sure to connect the adapter to the further USB TYPE A port from the LAN port and use the supplied adapter cover. Loosen the screw (marked with triangle) on the bottom left of the USB TYPE A ports. Insert the tab of the cover into the hole at the upper right of the USB TYPE A ports in the direction of the arrow.
  • Page 9: Turning On The Power

    Turning on the power projector and the outlet. POWER indicator Make sure that the POWER indicator is lighted in steady orange. Then remove the ON button lens cover. Press the STANDBY/ON button on the projector or the ON button on the remote control.
  • Page 10: Adjusting The Projector's Elevator

    Adjusting the projector’s elevator When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally. Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the projector within 9 degrees.
  • Page 11: Displaying The Picture

    Displaying the picture Activate your signal source. Turn the signal source on, and make it send the signal to the VOL + / - projector. buttons Press the INPUT button on the projector. Each time you press the button, the projector switches its input port in turn.
  • Page 12: Turning Off The Power

    Turning off the power POWER indicator Press the STANDBY/ON button on the STANDBY projector or the STANDBY button on button the remote control. on the screen for about 5 seconds. Press the STANDBY/ON or STANDBY button again while the message appears.
  • Page 13: Replacing The Lamp

    Replacing the lamp the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, make contact with your dealer and tell the lamp type number.
  • Page 14 Replacing the lamp (continued) HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE WARNING The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
  • Page 15 Please check and cle purchasing a new one. Type number : UX38242 Turn the projector off, and unplug the power down. Use a vacuum cleaner on and around the take it off. Press up slightly the bottom side knobs off. Extra knobs of the projector and the outer side of the...
  • Page 16 in the EASY MENU. (1) Press the MENU button to display a menu. cursor buttons, then press the cursor (or the ENTER / the RESET) button. A dialog will appear. WARNING projector. the projector. NOTE...
  • Page 17: Using The Cd Manual

    Using the CD manual The other manuals for this product are written into the included CD-ROM titled to ensure the proper use. System requirements The system for using the CD-ROM requires the following. Windows ® OS:Windows ® XP, Windows Vista ®...
  • Page 18 Item Product name Liquid crystal projector CP -X8170: 786,432 pixels (1024 horizontal x 768 vertical) CP -WX8265: Liquid Crystal 1,024,000 pixels (1280 horizontal x 800 vertical) Panel CP -WU8460: 2,304,000 pixels (1920 horizontal x 1200 vertical) Lamp 365W UHP Power supply, AC100-120 V: 5.1 A, AC220-240 V: 2.5 A Rated current Power...
  • Page 19 Item COMPUTER IN1 ......D-sub 15 pin mini jack x1 COMPUTER IN2 HDMI 1 ........... HDMI connector x1 HDMI 2 ........... HDMI connector x1 MONITOR OUT ......D-sub 15 pin mini jack x1 COMPONENT (Y, Cb/Pb, Cr/Pr) ....... RCA jack x3 S-VIDEO ..........
  • Page 20: Troubleshooting - Warranty And After-Service

    If this does not resolve the problem, please consult your dealer or service company. They will tell you what warranty condition is applied. for this projector. Product http://www.hitachi-america.us/projectors information and Manuals : Production http://www.hitachidigitalmedia.com information : http://www.hitachiserviceeu.com/support/guides/...

This manual is also suitable for:

Cp-wx8265Cp-x8170

Table of Contents