1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Fax Machine
  5. AR-FX12
  6. Service manual

Sharp AR-FX12 Service Manual

Hide thumbs Also See for AR-FX12:

Quick Links

See also: Operating Manual
[1]
PRODUCT OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
[2]
CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
[3]
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
[4]
[5]
UNPACKING AND INSTALLATION. . . . . . . . . . . . . . . . . . . . . . 5 - 1
[6]
SIMULATIONS, FAX SOFTWARE SWITCH. . . . . . . . . . . . . . . 6 - 1
[7]
MACHINE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1
[8]
ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1
Parts marked with "
" are important for maintaining the safety of the set.
Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
LASER PRINTER OPTIONS
FAX EXPANSION KIT

(For North America)

MODEL
OPTION
CONTENTS
SHARP CORPORATION
CODE : 00ZARFX12/A1E
AR-FX12
AR-MM9
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
loading

Related Manuals for Sharp AR-FX12

Summary of Contents for Sharp AR-FX12

  • Page 1: Table Of Contents

    CODE : 00ZARFX12/A1E LASER PRINTER OPTIONS FAX EXPANSION KIT (For North America) AR-FX12 MODEL OPTION AR-MM9 CONTENTS PRODUCT OUTLINE ....... . 1 - 1 CONFIGURATION .
  • Page 2 CONTENTS [1] PRODUCT OUTLINE ......1-1 [6] SIMULATIONS, FAX SOFTWARE SWITCH 1. Entering the simulation mode ....6-1 2.

  • Page 3: Product Outline

    Machines to install this unit : •AR-M355U/M455U •AR-M351U/M451U •AR-M355N/M455N •AR-M351N/M451N [2] CONFIGURATION Extended memory * Installed to FAX I/F PWB. FAX I/F PWB FAX Interface cable FAX-BOX unit *1) Installed to the machine MFP controller PWB. AR-FX12 PRODUCT OUTLINE • CONFIGURATION 1-1...

  • Page 4: Specifications

    Receive Automatic receive --- Resend Calls the previous destination. function Manual receive Reduction Calls the destination registration number by 10-key Memory receive destination input. Fixed size selection reduction receive Specified size zoom receive Rotational receive --- AR-FX12 SPECIFICATIONS 3-1...
  • Page 5 Sender table O (Sender registration Listed on the key operation table) list. Confidential box O (Integrated check table with the memory box table). Interface group O (Integrated table with the memory box table). Program table AR-FX12 SPECIFICATIONS 3-2...

  • Page 6: External Views And Internal Structures

    This key is also used to cancel resolution, paper size and special mode settings. ] key This is used to produce tone signals when you are on a pulse dial line. 8 [START] key Press to begin scanning an original for fax transmission. AR-FX12 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-1...

  • Page 7: Fax Mode (Condition Setting Screen)

    When a special mode such as polling or dual page scan is selected, a special mode icon appears here. * Can only be used on the AR-M355N/AR-M455N. The AR-M355U/AR-M455U models do not have this function. AR-FX12 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-2...
  • Page 8 When the network scanner option is installed and a destination other than a fax numbers is stored in a one-touch key, one of the following icons will appear. : Scan to E-mail destination : Internet fax destination : Scan to FTP destination : Scan to Desktop destination : Multiple destinations (Scan to E-mail, fax, etc.) AR-FX12 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-3...

  • Page 9: Pwb

    Supplies power to the FAX unit. 4 TEL/LIU PWB TEL line communication control 5 FAX I/F PWB (Installed to the machine side) Connection between FAX and MFP controller 6 FAX extended memory (Installed to FAX I/F PWB) AR-FX12 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-4...

  • Page 10: Unpacking And Installation

    Remove the two screws that secure the FAX I/F cover of the control PWB unit and remove the FAX I/F cover. • For installation of AR-FX12, the control PWB unit and the scanner unit must have been installed. • Start installation after checking that the COMMUNICATION indictor on the operation panel is neither lit nor blinking.
  • Page 11 10)Turn on the power switches of the main unit. Insert the power plug of the main unit to the outlet and turn on the power switch of the main unit and the fax power switch of the box unit. AR-FX12 UNPACKING AND INSTALLATION 5-2...
  • Page 12 <2>Use the 10-key pad to enter [66] in the main code entry screen and press the [START] key. <3>Use the 10-key pad to enter [10] in the sub-code entry screen and press the [START] key. AR-FX12 UNPACKING AND INSTALLATION 5-3...

  • Page 13: Simulations, Fax Software Switch

    16 Used to adjust the print density in the FAX mode Adjustment Picture (Ultra Fine mode). (Only when FAX is installed.) quality Data transfer Used to adjust laser power (absolute value) in the FAX Adjustment Operation reception mode. (Only when FAX is installed.) AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-1...
  • Page 14 19 Used to backup the Address data into the flash Memory Setup Operation (Option FAX memory:AR-MM9) (Only when FAX is installed.) 20 Used to restore the backup data (SIM 66-19) to Address data. Setup Operation (Only when FAX is installed.) AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-2...
  • Page 15 43 To execute this simulation, FAX program writing must be allowed. (Jumper and DIP switch which differ depending on the model)The adjustment value of PIC are changed and written. The current setting is highlighted beside the item. AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-3...

  • Page 16: Detail Of Simulations

    1. PRINT START When "1" is selected, press [START] key. Press [CUSTOM SETTINGS] key or [START] key SIMULATION 22-6 DATA PRINT MODE.. EXECUTING TRAY SELECT auto only (no selection) PRINT START AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-4...
  • Page 17 FAX SEND: Number of times of FAX sending FAX RECEIVE: Number of times of FAX reception FAX OUTPUT: FAX print quantity SEND IMAGES: Sending quantity SEND TIME: Time for sending RECEIVE TIME: Time for reception AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-5...
  • Page 18 Press [START] key or press [START] key. Press [CUSTOM SETTINGS] key SIMULATION 46-12 EXP. LEVEL SETUP FAX (AUTO SET). SELECT 1-5, AND PRESS START. (FEED TRAY) 1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4 5.BPT AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-6...
  • Page 19 Press [START] key or press [START] key. Press [CUSTOM SETTINGS] key SIMULATION 46-13 EXP. LEVEL SETUP FAX(NORMAL). SELECT 3-8, AND PRESS START. (EXP. LEVEL SELECT) 3. AUTO 4. 1.0 5. 2.0 6. 3.0 7. 4.0 8. 5.0 AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-7...
  • Page 20 EXP. LEVEL SETUP FAX(FINE). SELECT 3-14, AND PRESS START. (EXP. LEVEL SELECT) 3. AUTO 4. 1.0 5. 2.0 6. 3.0 7. 4.0 8. 5.0 9. AUTO(H) 10. 1.0(H) 11. 2.0(H) 12. 3.0(H) 13. 4.0(H) 14. 5.0(H) AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-8...
  • Page 21 EXP. LEVEL SETUP FAX(SUPER FINE). SELECT 3-14, AND PRESS START. (EXP. LEVEL SELECT) 3. AUTO 4. 1.0 5. 2.0 6. 3.0 7. 4.0 8. 5.0 9. AUTO(H) 10. 1.0(H) 11. 2.0(H) 12. 3.0(H) 13. 4.0(H) 14. 5.0(H) AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-9...
  • Page 22 EXP. LEVEL SETUP FAX(ULTRA FINE). SELECT 3-14, AND PRESS START. (EXP. LEVEL SELECT) 3. AUTO 4. 1.0 5. 2.0 6. 3.0 7. 4.0 8. 5.0 9. AUTO(H) 10. 1.0(H) 11. 2.0(H) 12. 3.0(H) 13. 4.0(H) 14. 5.0(H) AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-10...
  • Page 23 Operation/Procedure Set the Fax soft switch. Transfer from HDD to SRAM. If, however, a FAX memory or an (For details of the soft SW, refer to the AR-FX12 option memory (for FAX) is installed, the contents of the FAX Specifications.) memory are also transferred as well as the contents of HDD.
  • Page 24 MFP SRAM (MFP control PWB) SRAM MFP FLASH (FAX I/F PWB) FLASH Memory MFP OP.FLASH (FAX I/F PWB) FLASH Memory (AR-MM9) MODEM EEPROM (FAX PWB) MODEM SRAM(G/A) (FAX PWB) MODEM SDRAM1 (FAX PWB) MODEM SDRAM 2(FAX PWB) AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-12...
  • Page 25 15.2.4 V34 16.14.4 V33 17.12.0 V33 18.14.4 V17 19.12.0 V17 20.9.6 V17 21.7.2 V17 22.9.6 V29 23.7.2 V29 24.4.8 V27t 25.2.4 V27t 26.0.3 FLG 27.CED 2100 28.CNG 1100 29.0.3 V21 30.ANSam 31.RINGER 32.No RBT AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-13...
  • Page 26 15.2.4 V34 16.14.4 V33 17.12.0 V33 18.14.4 V17 19.12.0 V17 20.9.6 V17 21.7.2 V17 22.9.6 V29 23.7.2 V29 24.4.8 V27t 25.2.4 V27t 26.0.3 FLG 27.CED 2100 28.CNG 1100 29.0.3 V21 30.ANSam 31.RINGER 32.No RBT AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-14...
  • Page 27 MESSAGE2 MESSAGE2 MESSAGE3 MESSAGE3 MESSAGE4 MESSAGE4 MESSAGE5 MESSAGE5 MESSAGE6 MESSAGE6 MESSAGE7 MESSAGE7 MESSAGE8 MESSAGE8 MESSAGE9 MESSAGE9 MESSAGE10 MESSAGE10 MESSAGE11 MESSAGE11 MESSAGE12 MESSAGE12 MESSAGE13 MESSAGE13 MESSAGE14 MESSAGE14 MESSAGE15 MESSAGE15 ALARM ALARM RINGER RINGER EXT.TEL.RINGER EXT.TEL.RINGER AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-15...
  • Page 28 19.RINGER 20.EXT.TEL.RINGER IMAGE MEMORY CLEAR. EXECUTING... ++++++ Press [CUSTOM SETTINGS] key. During execution of image memory clear, "+" is displayed. When one block or a certain unit of area is cleared, "+" is added. AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-16...
  • Page 29 Press [CUSTOM SETTINGS] key. Press [CUSTOM SETTINGS] key. NO SIGNAL No signal NO SIGNAL No signal 11111 11111 11110 11110 00000 00000 010101 010101 00001 00001 AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-17...
  • Page 30 [1.MAKE TIME] Press [CUSTOM SETTINGS] key. SIMULATION 66-14 DIAL TEST(10PPS). EXECUTING... 1.MAKE TIME Execution Dial pulse make time setup (0 - 15) Dial is send with the setup value of +29ms. AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-18...
  • Page 31 SIMULATION 66-18 DTMF SIGNAL OUTPUT.(SOFT SW) INPUT 0 9,* ,#, AND PRESS START. Press [START] key. Press [CUSTOM SETTINGS] key. SIMULATION 66-18 DTMF SIGNAL OUTPUT.(SOFT SW) EXECUTING... 1 - 9, 0, *, # AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-19...
  • Page 32 However, data backed up in the Tiger series cannot be restored to the machine. If an option Flash ROM backed up in the Tiger series is installed, the data in the option Flash ROM are deleted. AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-20...
  • Page 33 Operation/Procedure 1) Select with 10 digit key pad and press START to execute the following. 1: Address data clear 2: Address data not clear SIMULATION 66-29 ADDRESS DATA CLEAR. ARE YOU SURE ? 1. YES 2. NO AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-21...
  • Page 34 Image quality Normal SIMULATION 66-35 Density Thin MODEM PROGRAM RELOAD. LOADER...OK MODEM...COMPLETE Sender record COMPLETE Writing completed Check sum error Write error Delete error Verify error Due to loader error AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-22...
  • Page 35 Data line repeat MFPC -> MDMC Data line repeat MFPC <- MDMC Command line once only MFPC -> MDMC Command line once only MFPC <- MDMC Command line repeat MFPC -> MDMC Command line repeat AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-23...
  • Page 36 (Because of FAX program write protection, etc.) 2) When YES is selected, the adjustment values are collectively written into the PIC installed to the FAX box. Normal completion of writing: "WRITING OK" In case of an error:"NG" AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-24...

  • Page 37: Fax Software Switch

    Remote switch Remote reception instruction SW 14-1 Remote switch inhibit setup Notification to external telephone in remote SW 14-2 switch Remote switch operation allowed SW 14-3 Remote switch is made when calling from external telephone. AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-25...
  • Page 38 To print after reception of each page 11 x 17 paper reception width setup SW 37-3 To print 11x17 document as B4 width Reception size specification SW 37-1~2 To limit the reception size. (Indicates reception capacity.) AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-26...
  • Page 39 Sender's number and send request allow number are collated each other. In this machine, Sharp's unique collating of system number ID number is not performed. 1: Not protected...
  • Page 40 Used to set whether B5R document is transmitted in A4 width (B5R) or the scan Rotate Send setup (B5R image is rotated and transmitted in B4 width (B5). (16K 16KR) 1: Send as A4 width 0: Send as B4 width document (B5R) document (B5) with without rotating rotating AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-28...
  • Page 41 Used to set the number of pages of scanning at the dial ringing timing in quick 1 page ringing in quick online online transmission. Can be set in the range of 1~15 pages by binary input. transmission 1-6 Not used AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-29...
  • Page 42 When set to "C" (BCD) or above, same as setting to the initial value of "5" (BCD). 55 (Japan) 5* (Outside Japan) Remote reception Used to set YES/NO of remote switch from an external telephone. instruction 1: NO (remote switch 0: YES (Remote switch disable) enable) AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-30...
  • Page 43 3,4 Coding capacity in send/ Used to set the coding capacity to transmit to the remote machine in V.34 JBIG/MMR/ receive communication. MR/MH (V.34 communication) Bit No. (Reflected on DIS/DCS/ JBIG/MMR/MR/MH DTC.) MMR/MR/MH MR/MH AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-31...
  • Page 44 3,4 Timer setup between Used to set the timer between Flag and address when receiving FSK signal in a 6sec flag and address communication other than V.34. (V.21-FSK) Bit No. 6sec 15sec 30sec 120sec Not used AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-32...
  • Page 45 When, for example, FINE is received, the threshold value is doubled. DCS-TCF interval time Used to set the time interval (sec) from DCS sending to TCF signal sending. 75msec 1: 150msec 0: 75msec The ITU-T standard is 75 ± 20ms. AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-33...
  • Page 46 Used to set how many EOL's are sent as RTC when sending Phase C. 6 times send 1: 12 times 0: 6 times When the other party cannot detect the RCP, it becomes easy to detect RCP. AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-34...
  • Page 47 Used to set the ID No. when the PBX function is enabled. This setting is valid Initial set up (1st digit: When dial when "ID" is set in SW59-7-8.If the set value is outside the specified range, the inputting or dialing) default (0) is used. AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-35...
  • Page 48 3,4 Received data print Used to set selection of the optimum paper for received data printing. Receive condition setup setup Bit No. Optimum size/Large size/reduction Optimum size/Large size Optimum size/Large size/Division Optimum size/Large size/reduction AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-36...
  • Page 49 Date/sender information Used to set the print position of the date/sender information at the top of the Outside the Send setup print position setup transmitted document. document 1: Top of document 0: Outside of document AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-37...
  • Page 50 Used to set whether the communication report table is outputted or not when Not output (When canceling) transmission is canceled during transmission of document. 1: Communication report 0: Communication report table is printed. table is not printed. AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-38...
  • Page 51 V.34 mode function Used to set Enable/Disable of V.34 mode function in the machine when Enable (When call out and sending. polling) 1: V.34 mode function 0: V.34 mode function disable enable AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-39...
  • Page 52 FAX signal cannot be received (when the sound response from the remote machine is a telephone in no response) from the remote machine in remote machine in FAX FAX reception (call-in). reception 1: Error sound provided 0: No error sound AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-40...
  • Page 53 CFR signal from the machine in the reception procedure other 1.6sec. than V.34. Bit No. 1600 Other value than the above: Set value x 200ms. 5-6 Not used AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-41...
  • Page 54 Used to set the volume of transmission end sound from the speaker when FAX Sound NO volume transmission is completed. The sound volume is available in the following 4 kinds. Bit No. Sound NO Small Medium Large AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-42...
  • Page 55 7,8 Line monitor sound Used to set the sound level of "Medium" line monitor sound (key operation Sound volume "Medium" setup setup) from the speaker. volume 4 Bit No. Sound volume2 Sound volume3 Sound volume4 Sound volume5 AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-43...
  • Page 56 Not used Recall allow in busy Used to set whether recall is made or not when the other party is busy or does Recall Send setup not receive in transmission. 1: Recall 0: Not recall AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-44...
  • Page 57 5-8 Break time (10PPS) Used to set the break time when dialing at 10PPS. 60ms Adjustment setup The set range is 0 - 15 by binary input of N into "N +56ms" (56 - 71ms). value AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-45...
  • Page 58 The set range is 0 - 255 by binary input of N into "1ms x N" (50ms - 255ms).If set to outside the set range, it is set to the default (120ms). AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-46...
  • Page 59 250ms detection time frequency. To count a busy tone signal as 1 pulse, it must be detected for more (ON time) than the set time. Bit No. 250ms 150ms 450ms 350ms For CTR21, 150ms. AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-47...
  • Page 60 1 pulse. The lower limit of OFF time can be set in the range of 0 - 150ms by binary input of N (0 - 15) into "N x 100ms." AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-48...
  • Page 61 When CI signal of other pattern than the set pattern is detected, auto call-in is not made. Bit No. STANDARD Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 ON (Australia) ON (Newzealand) 78 1-8 Not used 79 1-8 Not used 80 1-8 Not used AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-49...
  • Page 62 5,6 File compression type in Used to set the file compression type in broadcast including the remote side of broadcast (Including the Scan to E-mail. remote side in Scan to Bit No. E-mail) MR does not function. AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-50...
  • Page 63 Not used Switch from the image Used to set whether the image send display is switched to the copy display or Switch send display to the copy not. display 1: Switch 0: Not switch AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-51...
  • Page 64 FTP backup of iFAX receive data. The set range is 0 - 7 times by binary input. When set to "0," re-backup is not performed. 4-8 Not used From Not used AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-52...

  • Page 65: Machine Operation

    (recall:1/2* - 14time interval:1 - 3* - 15min) Quick on line sending Enable*/ Disable When the network scanner option is installed When extension phone is connected This setting is only effective if the other machine is a G3 machine that supports ECM AR-FX12 MACHINE OPERATION 7-1...

  • Page 66: Originals That Can Be Faxed

    8-1/2" x 11" (A4) 8-1/2" x 11"R (A4R) 1 : 0.5 (1 : 0.5) A document can also be faxed without reducing its size. In this case, the left and right edges will not be transmitted. AR-FX12 MACHINE OPERATION 7-2...

  • Page 67: Own Number Sending

    The top edge of the scanned data will be cut off by the sender's information; however, when both the sender and the receiver use the same size of paper, the printed fax will neither be reduced nor split up and printed on two pages. AR-FX12 MACHINE OPERATION 7-3...

  • Page 68: Trouble Codes

    The FAX-BOX PWB is not one for the AR- FX12(FAX detection). A. Details of trouble codes Details The Modem controller PWB of the FAX-BOX is not for the AR-FX12. MAIN SUB Cause Because the FAX-BOX modem controller Content Communication trouble (ICU detection) PWB information (hard detection) is not for between ICU and FAX.
  • Page 69 Registered contents are deleted. Register the deleted contents again. Cancel the U2 trouble with SIM16. Replace the HD PWB. Replace the ICU PWB. AR-FX12 MACHINE OPERATION 7-5...
  • Page 70 In confidential sending, the remote party does not have confidential function. remote party) (Including other company's machines) <1>The NSF signal has not "Confidential function" bit. <2>The NSF is not a Sharp machine. (Confidential not received) <1>In confidential sending, DCN is received for NSS. (Confidential BOX NO NG) <1>In confidential reception, a confidential box number which is not registered is...
  • Page 71 In E-mail/FTP , internet FAX send, the send data size exceeds the upper limit of send data. REJECTED In e-mail receive, a sender is registered in receive reject address/domain. NG85XXXX* In e-mail receive, an error occurs in communication with POP3 server. •Header acquisition error. •Time-out during mail receive AR-FX12 MACHINE OPERATION 7-7...
  • Page 72 V.34 MODE COMMUNICATION V.34 MODE COMMUNICATION EOR-Q V.34 MODE COMMUNICATION PPS-PRI-Q V.34 MODE COMMUNICATION V.8Phase-1 V.8Phase-1 V.34 MODE COMMUNICATION V.8Phase-2 V.8Phase-2 V.34 MODE COMMUNICATION V.8Phase-3 V.8Phase-3 V.34 MODE COMMUNICATION •For report codes 16 ~ 31, V.34 MODE COMMUNICATION. AR-FX12 MACHINE OPERATION 7-8...
  • Page 73 The TIFF type of the attached file in received e-mail cannot be recognized. Tag parameter error The TIFF type of the attached file in received e-mail cannot be recognized. Header size error The TIFF type of the attached file in received e-mail cannot be recognized. Data error AR-FX12 MACHINE OPERATION 7-9...
  • Page 74 In SMTP e-mail receive, an attached file cannot be stored in memory. Cannot be stored in memory. *1: Does not occur in Tiger and Dragon. When the sub code is 08 or 30, if the communication report is OK, the report code is 00 or 16. AR-FX12 MACHINE OPERATION 7-10...

  • Page 75: Electrical Section

    [8] ELECTRICAL SECTION 1. Block Diagram AR-FX12 ELECTRICAL SECTION 8-1...

  • Page 76: Actual Wiring Diagram

    2.Actual Wiring Diagram AR-FX12 ELECTRICAL SECTION 8-2...

  • Page 77: Circuit Diagram

    3.Circuit Diagram FAX I/F PWB (1/5) AR-FX12 ELECTRICAL SECTION 8-3...
  • Page 78 FAX I/F PWB (2/5) AR-FX12 ELECTRICAL SECTION 8-4...
  • Page 79 FAX I/F PWB (3/5) AR-FX12 ELECTRICAL SECTION 8-5...
  • Page 80 FAX I/F PWB (4/5) AR-FX12 ELECTRICAL SECTION 8-6...
  • Page 81 FAX I/F PWB (5/5) AR-FX12 ELECTRICAL SECTION 8-7...
  • Page 82 MDMC PWB (1/8) AR-FX12 ELECTRICAL SECTION 8-8...
  • Page 83 MDMC PWB (2/8) AR-FX12 ELECTRICAL SECTION 8-9...
  • Page 84 MDMC PWB (3/8) AR-FX12 ELECTRICAL SECTION 8-10...
  • Page 85 MDMC PWB (4/8) AR-FX12 ELECTRICAL SECTION 8-11...
  • Page 86 MDMC PWB (5/8) AR-FX12 ELECTRICAL SECTION 8-12...
  • Page 87 MDMC PWB (6/8) AR-FX12 ELECTRICAL SECTION 8-13...
  • Page 88 MDMC PWB (7/8) AR-FX12 ELECTRICAL SECTION 8-14...
  • Page 89 MDMC PWB (8/8) AR-FX12 ELECTRICAL SECTION 8-15...
  • Page 90 TEL/LIU PWB(USA) (1/3) AR-FX12 ELECTRICAL SECTION 8-16...
  • Page 91 TEL/LIU PWB(USA) (2/3) AR-FX12 ELECTRICAL SECTION 8-17...
  • Page 92 TEL/LIU PWB(USA) (3/3) AR-FX12 ELECTRICAL SECTION 8-18...

  • Page 93: Part Layout

    4.Part Layout A. FAX I/F PWB_U AR-FX12 ELECTRICAL SECTION 8-19...
  • Page 94 B.MDMC PWB_U AR-FX12 ELECTRICAL SECTION 8-20...
  • Page 95 AR-FX12 ELECTRICAL SECTION 8-21...
  • Page 96 C.TEL/LIU PWB_U AR-FX12 ELECTRICAL SECTION 8-22...

  • Page 97: Parts Guide

    拡張キット 拡張キット 拡張キット FAX拡張キット DIGITAL LASER COPIRER/ PRINTER OPTION FAX EXPANSION KIT AR-FX12 MODEL CONTENTS 1 FAX BOX ﾕﾆｯﾄ (FAX BOX UNIT) 2 梱包及び付属品 (Packing material&Accessories) 3 TEL/LIU 基板 (TEL/LIU PWB U)…JAPAN 4 TEL/LIU 基板 (TEL/LIU PWB U)…USA,CANADA 5 TEL/LIU 基板 (TEL/LIU PWB U)…EUROPE 6 TEL/LIU 基板...

  • Page 98: Fax Box ﾕﾆｯﾄ (Fax Box Unit)

    補修部品のランク付 市場における補修部品の在庫管理が、適正に運営出来る手助けとなることを、目的とします。 Aランク : メンテナンスパーツ、メンテナンスパーツには入っていないがメンテナンスパーツに近い消耗パーツ。 Bランク : 性能・機能パーツ（センサー、クラッチ等の電気パーツ） 、消耗パーツ。 Eランク : 基板含むユニットパーツ。 Dランク : 整備パーツ（外装、パッキング、同梱パーツ） 。 Cランク : 上記ランク以外のパーツ（基板の子部品を除いたもの） 。 DEFINITION Rank A : Maintenance parts, and consumable parts which are not included in but closely related to maintenance parts Rank B : Performance/function parts (sensors, clutches, and other electrical parts), consumable parts Rank E : Unit parts including PWB Rank D : Preparation parts (External fitting, packing, parts packed together)
  • Page 99 FAX BOX ﾕﾆｯﾄ (FAX BOX UNIT) PRICE RANK PART PARTS CODE DESCRIPTION MARK RANK 41 LHLDW2087SCZZ [Japan] ﾐﾆｸﾗﾝﾌﾟ Wire holder 43 LX-BZ0938FCZZ FAX ﾎﾙﾀﾞｰﾋﾞｽ FAX holder screw 45 LX-WZ0443FCZZ ｱｰｽ用平ﾜｯｼｬ Washer 46 XBPS726P08000 ﾋﾞｽ Screw(2.6×8) CPLTM5788FCE9 [Japan] FAX 電源ﾕﾆｯﾄ FAX power supply unit CPLTM5788FCF0 [100V series] FAX 電源ﾕﾆｯﾄ...

  • Page 100: 梱包及び付属品 (Packing Material&Accessories)

    梱包及び付属品 (Packing material & Accessories) PRICE RANK PART PARTS CODE DESCRIPTION MARK RANK 1 SPAKA6150FCZZ FAX ｷｯﾄｱﾄﾞ FAX kit add 2 SSAKA3640QCZZ ﾎﾟﾘ袋 Vinyl bag(320×690mm) 3 SPAKA6151FCZZ FAX ｷｯﾄｽﾍﾟｰｻｰ FAX kit spacer TCADZ1696FCZZ [Japan] FAX 設置手順書 FAX inst.manual TCADZ1697FCZZ [except Japan] FAX 設置手順書 FAX inst.manual TINSJ2785FCZZ [Japan] FAX 取扱説明書...
  • Page 101 TEL/LIU 基板 (TEL/LIU PWB U)…JAPAN PRICE RANK PART PARTS CODE DESCRIPTION MARK RANK 1 QCNCM1156FCZZ [CN3] ｺﾈｸﾀｰ Connector(S03B-XASK-1) 2 QCNCW1155FCZZ [CN2] ｺﾈｸﾀｰ Connector(30FE-BT-VK-N) 3 QJAKT0001FCZZ [MJ1] ﾓｼﾞｭﾗｰｼﾞｬｯｸ Modular Jack(MJ62J-RD315) 4 QJAKT0002FCZZ [MJ2] ﾓｼﾞｭﾗｰｼﾞｬｯｸ Modular Jack(MJ66J-RD315) 5 QSOCD0081FCZZ [CN1] ｿｹｯﾄ Socket(MD-S6350-90) 6 RCILZ0089FCZZ [L12] ｺｲﾙ...
  • Page 102 TEL/LIU 基板 (TEL/LIU PWB U)…JAPAN PRICE RANK PART PARTS CODE DESCRIPTION MARK RANK Resistor(1/16W 3.3KΩ ±5%) 79 VRS-CZ1JD332J [R19] 抵抗 Resistor(1/16W 36KΩ ±5%) 80 VRS-CZ1JD363J [R47] 抵抗 Resistor(1/16W 3.9KΩ ±5%) 81 VRS-CZ1JD392J [R55] 抵抗 Resistor(1/16W 39KΩ ±5%) 82 VRS-CZ1JD393J [R18] 抵抗 Resistor(1/16W 4.7KΩ...
  • Page 103 TEL/LIU 基板 (TEL/LIU PWB U)…USA,CANADA PRICE RANK PART PARTS CODE DESCRIPTION MARK RANK Resistor(1/16W 10KΩ ±5%) 52 VRS-CZ1JD103J [R1,R27,R31,R32,R41,R60,R61] 抵抗 Resistor(1/16W 11KΩ ±1%) 53 VRS-CZ1JD113F [R74] 抵抗 Resistor(1/16W 11KΩ ±5%) 54 VRS-CZ1JD113J [R75] 抵抗 Resistor(1/16W 15KΩ ±5%) 55 VRS-CZ1JD153J [R72] 抵抗 Resistor(1/16W 18KΩ...

  • Page 104: Tel/Liu 基板 (Tel/Liu Pwb U)

    TEL/LIU 基板 (TEL/LIU PWB U)…EUROPE PRICE RANK PART PARTS CODE DESCRIPTION MARK RANK Resistor(1/4W 10Ω ±5%) 50 VRD-HT2EY100J [R19,R24] 抵抗 Resistor(1/4W 10KΩ ±5%) 51 VRD-HT2EY103J [R35] 抵抗 52 VRD-HT2EY113J Resistor(1/4W 11KΩ ±5%) [R22] 抵抗 Resistor(1/4W 12Ω ±5%) 53 VRD-HT2EY120J [R30] 抵抗 Resistor(1/4W 12KΩ...

  • Page 105: Tel/Liu 基板 (Tel/Liu Pwb U)

    TEL/LIU 基板 (TEL/LIU PWB U)…Australia,New Zealand PRICE RANK PART PARTS CODE DESCRIPTION MARK RANK 36 VHEMTZJ4R7B-1 [ZD3,ZD4,ZD9,ZD10] ﾂｪﾅｰﾀﾞｲｵｰﾄﾞ Zener diode(MTZJ4R7B) 37 VHEMTZJ6R8B-1 [ZD6] ﾂｪﾅｰﾀﾞｲｵｰﾄﾞ Zener diode(MTZJ6.8B) 38 VHIBU4066BCF1 IC(BU4066BCF1) [IC5] IC 39 VHINJM3414M-1 IC(NJM3414M) [IC1,IC2] IC 40 VHINJM4558MF1 IC(NJM4558MF1) [IC4] IC 41 VHITHS56F//-1 IC(THS56F) [IC3] IC...

  • Page 106: ﾓﾃﾞﾑｺﾝﾄﾛｰﾙ基板 (Modem Control Pwb U)

    ﾓﾃﾞﾑｺﾝﾄﾛｰﾙ基板 (Modem control PWB U) PRICE RANK PART PARTS CODE DESCRIPTION MARK RANK 1 QCNCM1069ACZZ [CN8] ｺﾈｸﾀｰ Connector(6pin) 2 QCNCM7014SC0B [CN5] ｺﾈｸﾀｰ Connector(2pin) 3 QCNCM7014SC0C [CN7] ｺﾈｸﾀｰ Connector(3pin) 4 QCNCW1155FCZZ [CN6] ｺﾈｸﾀｰ Connector(30FE-BT-VK-N) 6 QSOCN0082FCZZ [CN1] ｿｹｯﾄ Socket(DX10G1M26SE) 7 QSOCZ0094FCPZ [CN4] ROM ｿｹｯﾄ...
  • Page 107 ﾓﾃﾞﾑｺﾝﾄﾛｰﾙ基板 (Modem control PWB U) PRICE RANK PART PARTS CODE DESCRIPTION MARK RANK Resistor(1/16W 0Ω ±5%) VRS-CZ1JD000J [R180,R181,R189,R190,R191,R192,R193,R210,R211,R212] 抵抗 Resistor(1/16W 0Ω ±5%) VRS-CZ1JD000J [R215,R217,R228,R246] 抵抗 Resistor(1/16W 100Ω ±5%) 64 VRS-CZ1JD101J [R141,R223,R255] 抵抗 Resistor(1/16W 1.0KΩ ±5%) VRS-CZ1JD102J [R10,R15,R65,R66,R67,R109,R111,R113,R114,R116,R139] 抵抗 Resistor(1/16W 1.0KΩ ±5%) VRS-CZ1JD102J [R140,R149,R174,R195,R243,R244] 抵抗...

  • Page 108: Fax ｲﾝﾀｰﾌｪｰｽ基板 U(Fax Interface Pwb U)

    FAX ｲﾝﾀｰﾌｪｰｽ基板 U(FAX interface PWB U) PRICE RANK PART PARTS CODE DESCRIPTION MARK RANK 1 QCNCW1180FCZZ [CN3] ｺﾈｸﾀｰ Connector(100R2.8JXKS) 2 QSOCN0082FCZZ [CN1] ｿｹｯﾄ Socket(DX10G1M26SE) 3 QSOCZ0092FCZZ [CN2] ｿｹｯﾄ Socket(177827-1) 4 RC-KZ0008QCZZ [C1,C2,C7,C8,C12,C13,C14,C15] ｺﾝﾃﾞﾝｻｰ Capacitor(50WV 0.1µF) 5 VCEASM1CM106M [C24] ｺﾝﾃﾞﾝｻｰ Capacitor(16WV 10µF) 6 VCKYCZ1CF104Z [C3,C4,C5,C6,C9,C10,C11,C17,C25] ｺﾝﾃﾞﾝｻｰ...
  • Page 109 FAX AC 電源基板 (FAX AC power supply unit)…100V series PRICE RANK PART PARTS CODE DESCRIPTION MARK RANK 56 0FT23538923// [R37] ﾁｯﾌﾟ抵抗器 Resistor(RK73K2ATD 3.9KΩJ) 57 0FT23538974// [R7] ﾁｯﾌﾟ抵抗器 Resistor(RK73K2ATD 2.7KΩJ) 58 0FT23538982// [R23] ﾁｯﾌﾟ抵抗器 Resistor(RK73K2ATD 47ΩJ) 59 0FT23541509// [D11] ﾁｯﾌﾟﾂｪﾅｰﾀﾞｲｵｰﾄﾞ Zener diode(RD8.2M-B2) 60 0FT23546047// [R57] ﾁｯﾌﾟ抵抗器...
  • Page 110 FAX AC 電源基板 (FAX AC power supply unit)…100V series PRICE RANK PART PARTS CODE DESCRIPTION MARK RANK 136 0FT23429199// [D14] ﾀﾞｲｵｰﾄﾞ Diode(AK04V0) 137 0FT23484661// [R84] 酸化金属被膜抵抗器 Resistor(RSMF12TS 0.22ΩJ) 138 0FT23486796// [C11] ｾﾗﾐｯｸｺﾝﾃﾞﾝｻ Capacitor(DE0905-979R471K2K) 139 0FT23486850// [C12] ﾌｨﾙﾑｺﾝﾃﾞﾝｻ Capacitor(ECQ-B1H473KF4) 140 0FT23486850// [C16] ﾌｨﾙﾑｺﾝﾃﾞﾝｻ...

  • Page 111: Ffax Ac 電源基板 (Fax Ac Power Supply Unit)

    FAX AC 電源基板 (FAX AC power supply unit)…200V series PRICE RANK PART PARTS CODE DESCRIPTION MARK RANK 1 0FT23581330// [CX1] ﾁｯﾌﾟｾﾗﾐｯｸｺﾝﾃﾞﾝｻ Capacitor(GRM40R104K25PT (1RL=3000)) 2 0FT23581330// [CX2] ﾁｯﾌﾟｾﾗﾐｯｸｺﾝﾃﾞﾝｻ Capacitor(GRM40R104K25PT (1RL=3000)) 3 0FT23415570// [RX1] ｶｰﾎﾞﾝ抵抗器 Resistor(RDMF14 TS 1 K OHMJ) 4 0FT23536106// [RX2] ﾁｯﾌﾟ抵抗器...
  • Page 112 FAX AC 電源基板 (FAX AC power supply unit)…200V series PRICE RANK PART PARTS CODE DESCRIPTION MARK RANK 88 0FT33529090// [L] ﾌｧｽﾄﾝ端子 Terminal(85163 #250) 89 0FT33684207// [L1] ﾘｱｸﾄﾙ Reactle(LF-4ZA-E183) 90 0FT23642925// [L4] ﾘｱｸﾄﾙ Reactor(TG0113MADS SK) 91 0FT33529090// [L1F] ﾌｧｽﾄﾝ端子 Terminal(85163 #250) 92 0FT33529090// [N] ﾌｧｽﾄﾝ端子...
  • Page 113 FAX AC 電源基板 (FAX AC power supply unit)…200V series PRICE RANK PART PARTS CODE DESCRIPTION MARK RANK 167 0FT35866337// [T2] 変圧器 Transformer(EXT43441-009A) 168 0FT33673027// [TH1] ｻｰﾐｽﾀ Thermister(SCK-104) 169 0FT23671666// IC(UPC78M12AHF) [Z1] IC 170 0FT23665429// IC(UPC78M24AHF) [Z2] IC 171 0FT33603762// IC(PQ12RF1) [Z3] IC 172 0FT33331673// [Z4] IC ﾚｷﾞｭﾚｰﾀ...

  • Page 114: 索引 (Index)

    索引 (Index) PRICE R. PARTS CODE NEW P/R PRICE R. QSOCZ0092FCZZ AR EQ PARTS CODE NEW P/R QSOCZ0094FCPZ QSW-C9295QCZZ 1- 15 CPLTM5788FCE9 1- 501 RADPA0001QSZZ CPLTM5788FCF0 2- 19 AQ EQ 1- 501 CPLTM5788FCF2 RADPA0002TSZZ 1- 501 2- 19 RC-EZ0362FCPZ CPWBN1619FCE1 1- 34 3- 18 AC DD...
  • Page 115 PRICE R. PRICE R. PARTS CODE PARTS CODE NEW P/R NEW P/R TINSE2786FCZZ VHDS1ZB60//-1 BD GN 6- 30 TINSE2787GHZZ VHEHZS2C1//-1 3- 38 TINSE2791FCZZ BE GN " 4- 28 TINSF2789GHZZ " 5- 36 TINSG2788GHZZ " 6- 33 TINSJ2785FCZZ VHEMTZJ30B/-1 5- 37 TINSW2790GHZZ "...
  • Page 116 PRICE R. PRICE R. PARTS CODE PARTS CODE NEW P/R NEW P/R VRD-HT2EY113J VRS-CZ1JD223J 5- 52 AA DD 4- 58 AA DD VRD-HT2EY120J " 5- 53 AA DD 5- 67 AA DD VRD-HT2EY123J 5- 54 AA DD " 6- 62 AA DD VRD-HT2EY124J VRS-CZ1JD243J...
  • Page 117 PRICE R. PRICE R. PARTS CODE PARTS CODE NEW P/R NEW P/R VS2SD592A//-1 0FT23415651// 7- 97 9- 132 VS2SD592A-S-1 0FT23415716// 3- 96 AK DX 9- 133 " 4- 73 AK DX 0FT23415740// 10- 143 VSDTA114EUA-1 " 7- 98 9- 134 VSDTC143ZKA-1 0FT23415899// 3- 97...
  • Page 118 PRICE R. PRICE R. PARTS CODE NEW P/R PARTS CODE NEW P/R 0FT23549119// 10- 42 0FT23624293// 10- 118 " " 10- 43 9- 80 " 0FT23625591// 9- 62 10- 134 " " 9- 63 10- 138 " " 9- 64 9- 81 "...
  • Page 119 PRICE R. PRICE R. PARTS CODE NEW P/R PARTS CODE NEW P/R 0FT33213581// 10- 182 AP EQ " 9- 175 AP EQ 0FT33213786// AK DX " AK DX " 9- 162 AK DX " 9- 163 AK DX 0FT33258410// 10- 94 0FT33262132// 10- 95 AP EQ...
  • Page 120 CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
  • Page 122 COPYRIGHT 2004 BY SHARP CORPORATION All rights reserved. All rights reserved. All rights reserved. Printed in Japan. Printed in Japan. Printed in Japan. No part of this publication may be reproduced, No part of this publication may be reproduced, No part of this publication may be reproduced,...

This manual is also suitable for:

Ar-mm9